• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.34-36
• /
• 2007

A new soft switching boost converter is proposed in this paper. The conventional boost converter generates switching losses at turn on and off. Because of that, the whole system efficiency is reduced. The proposed converter utilizes soft switching method using an auxiliary switch and resonant circuit. Thus, the converter reduces switching losses lower than ones of hard switching method. The proposed soft switching boost converter can be applied to photovoltaic system, power factor correction circuit and so on.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.84-86
• /
• 2009

Isolated boost converter is desirable in the dc/dc converter applications where isolation is required and a large step up is needed. In this paper, it is proposed and analyzed the isolated boost converter which can step up low input voltage to high output voltage using transformer. Instead of using a conventional scheme, the proposed converter has the reset winding for volt-sec balance of transformer. Finally, the validity of the proposed isolated boost converter is verified by simulation.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.523-525
• /
• 2008

Novel zero-voltage switching(ZVS) dual inductor-fed DC-DC converter integrating a conventional dual inductor-fed boost converter(DIFBC) and a parallel bidirectional boost converter has been proposed. Most of current-fed type boost topologies including dual inductor schemes have crucial defects such as a high voltage spike on the main switch when it comes to turning off, an unattainable soft start-up due to the limited range of duty ratio, above 50%, and considerable switching losses due to the hard switching. By adding two auxiliary switches and an output capacitor on the conventional DIFBC, the proposed circuit can solve mentioned problems and improve the efficiency with simple methods. The operational principle and theoretical analysis of the proposed converter have been included. Experimental results based on a 42V input, 400V/1A output and 50kHz prototype are shown to verify the proposed scheme.

• Journal of Power Electronics
• /
• v.9 no.3
• /
• pp.430-437
• /
• 2009

This paper presents the dynamic characteristics of buck and buck-boost dc-dc converters with digital filters. At first, the PID, the minimum phase FIR filter and the IIR filter controls are discussed in the buck dc-dc converter. Comparisons of the dynamic characteristics between the buck and buck-boost converters are then discussed. As a result, it is clarified that the superior dynamic characteristics are realized in the IIR filter method. In the buck converter, the undershoot is less than 2% and the transient time is less than 0.4ms. On the other hand, in the buck-boost converter, the undershoot is about 3%. However, the transient time is approximately over 4ms because the output capacitance is too large to suppress the output voltage ripple in this type of converter.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1052-1054
• /
• 2001

This paper describes a boost converter to be operated at the boundary of continuous current mode(CCM) and discontinuous current mode(DCM) for power factor correction and low cost. A control method to be utilized in simulation is a average-current mode method in case of operating in CCM. The simulation results show that Better is the CCM converter then the DCM converter in harmonic content and input current waveform. And A Double-boost converter is superior to single-boost converter for input-current harmonic.

• Proceedings of the KIEE Conference
• /
• 2004.07e
• /
• pp.14-16
• /
• 2004

This paper describes a boost converter to be operated at the boundary of continuous current mode(CCM) and discontinuous current mode(DCM) for power factor correction and low cost. A control method to be utilized in simulation is a average Current mode method in case of operating in CCM. The simulation results show that Better is the CCM converter then the DCM converter in harmonic content and input current waveform. And A Double-boost converter is superior to single-boost converter for input-current harmonic.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2016-2023
• /
• 2016

This paper presents a simple input-constrained current controller for a DC/DC boost converter with stability analysis that considers the nonlinearity of the converter model. The proposed controller is designed to satisfy the inherent input constraints of the converter under a physically reasonable assumption, which is the first contribution of this paper. The second contribution is providing a rigorous proof of the proposed control law, which keeps the closed-loop system along with the internal dynamics stable. The performance of the proposed controller is demonstrated through an experiment employing a 20-kW DC/DC boost converter.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.1
• /
• pp.171-178
• /
• 2010

Resonant parametric perturbation (RPP) method is an effective non-feedback method for controlling chaos. In this paper, the above method is applied for the current programmed buck-boost dc-dc converter which exhibits chaotic for wide parameter variations. The different possible operating regimes leading to chaotic operation of the current mode controlled buck-boost converter is discussed and the control of chaos by RPP method is demonstrated through computer simulations and experimental studies. The converter is stabilized to period 1 operation practically.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.349-356
• /
• 2014

As the turns ratio of the tapped-inductor contributes to the step-up ratio, the tapped-inductor boost (TIB) converter has significantly increased level of difficulties in its analysis and design compared to the conventional boost converter where the duty ratio is the sole factor affecting the step-up ratio. In this paper, the operation of the continuous current mode TIB converter is briefly reviewed, the characteristics are analyzed in detail, and a design guideline optimizing the loss in the tapped-inductor is presented with a practical design example. Finally, experimental results from a 12V/120V prototype for 0.25A LED driver application are also presented to confirm the design.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.121-123
• /
• 2008

A high efficiency soft switching boost converter is proposed in this paper. The conventional boost converter generates switching losses at turn on and off. Because of those, the whole system efficiency is reduced. The proposed converter utilizes soft switching method using resonant circuit with an auxiliary switch. Therefore, the proposed converter reduces switching losses lower than the hard switching. The proposed soft switching boost converter can be applied to photovoltaic system, power factor correction circuit and etc.