• 한국재료학회지
• /
• 제22권11호
• /
• pp.575-580
• /
• 2012

The purpose of this study is to investigate the crystalline structure and optical properties of (GaZn)(NO) powders prepared by solid-state reaction between GaOOH and ZnO mixture under $NH_3$ gas flow. While ammoniation of the GaOOH and ZnO mixture successfully produces the single phase of (GaZn)(NO) solid solution within a GaOOH rich composition of under 50 mol% of ZnO content, this process also produces a powder with coexisting (GaZn)(NO) and ZnO in a ZnO rich composition over 50 mol%. The GaOOH in the starting material was phase-transformed to ${\alpha}$-, ${\beta}-Ga_2O_3$ in the $NH_3$ environment; it was then reacted with ZnO to produce $ZnGa_2O_4$. Finally, the exchange reaction between nitrogen and oxygen atoms at the $ZnGa_2O_4$ powder surface forms a (GaZn)(NO) solid solution. Photoluminescence spectra from the (GaZn)(NO) solid solution consisted of oxygen-related red-emission bands and yellow-, green- and blue-emission bands from the Zn acceptor energy levels in the energy bandgap of the (GaZn)(NO) solid solutions.

• Current Photovoltaic Research
• /
• 제2권3호
• /
• pp.88-94
• /
• 2014

The structural, optical and electrical properties of sputter-deposited CIGS films were directly influenced by the sputtering process parameters such as substrate temperature, working pressure, RF power and distance between target and substrate. CIGS thin films deposited by using a quaternary target revealed to be Se deficient due to Se low vapor pressure. This Se deficiency affected the overall stoichiometry of the films, causing the films to be Cu-rich. Current tends to pass through the Cu-Se channels which act as the shunting path increasing the film conductivity. The crystal structure of CIGS thin films depends on the substrate orientation due to the influence of surface morphology, grain size and stress of Mo substrate. The excess of Cu was removed from the CIGS films by KCN treatment, achieving a suitable Cu concentration (referred as Cu-poor) for the fabrication of solar cell. Due to high Cu concentrations on the CIGS film surface induced by Cu-Se phases after CIGS film deposition, KCN treatment proved to be necessary for the fabrication of high efficiency solar cells. Also during KCN treatment, dislocation density and lattice parameter decreased as excess Cu was removed, resulting in increase of bandgap and the decrease of conductivity of CIGS films. It was revealed that Cu-Se secondary phase could be removed by KCN wet etching of CIGS films, allowing the fabrication of high efficiency absorber layer.

• 대한전자공학회논문지SD
• /
• 제38권4호
• /
• pp.251-265
• /
• 2001

반도체 소자가 소형화 되면서 소자의 신뢰성을 유지하고 전력 소모를 줄이기 위해 기가-비트 DRAM의 동작 전압은 1.5V 이하로 줄어들 것으로 기대된다. 따라서 기가-비트 DRAM을 구현하기 위해 저전압 회로 설계 기술이 요구된다. 이 연구에서는 지금까지 발표된 저전압 DRAM 회로 설계 기술에 대한 조사결과를 기술하였고, 기가-비트 DRAM을 위해 4가지 종류의 저전압 회로 설계 기술을 새로이 제안하였다. 이 4가지 저전압 회로 설계 기술은 subthreshold 누설 전류를 줄이는 계층적 negative-voltage word-line 구동기, two-phase VBB(Back-Bias Voltage) 발생기, two-phase VPP(Boosted Voltage) 발생기와 밴드갭 기준전압 발생기에 대한 것인데, 이에 대한 테스트 칩의 측정 결과와 SPICE 시뮬레이션 결과를 제시하였다.

• 한국정보통신학회논문지
• /
• 제20권11호
• /
• pp.2085-2092
• /
• 2016

IC 기판의 가장 중요한 성질들의 하나는 넓은 영역에 걸쳐 균일해야만 한다는 것이다. 웨이퍼 결함 분석의 다양한 물리적 접근 방법 중에서 적외선 조사 기법에 특별한 관심이 모아지고 있다. 특히, 높은 공간적 분해력을 가지고 있는 근적외선 흡수 방법은 반-절연 GaAs 내의 결함들을 직접적으로 관찰하는데 이용되고 있다. 적외선 전송에 기초를 둔 이 기법은 신속하고 비파괴 적이다. 이 방법은, 직접적으로 GaAs 반도체의 적외선 영상은 결함의 광흡수 작용에 기인한 것임을 밝히고 있다. 반-절연 GaAs 내의 EL2에 관련된, 비 균일 적으로 분포된 결함들의 적외선 흡수 영상에서 콘트라스트가 반전되는 현상에 대해 새로운 모델을 제시하고 있다. 저온 포토퀀칭 실험은, 직접적인 방법으로, GaAs 웨이퍼의 콘트라스트 반전 영상은 밴드갭의 지엽적인 변동이나 전하 재분포에 의한 것이 아니라 흡수와 산란의 두 메커니즘에 의한 것임을 증명하고 있다.

• 한국재료학회지
• /
• 제22권7호
• /
• pp.352-357
• /
• 2012

$SnO_2$-mixed and Sn-doped $TiO_2$ nanoparticles were synthesized via a hydrothermal process. $SnO_2$-mixed $TiO_2$ nanoparticles prepared in a neutral condition consisted of anatase $TiO_2$ nanoparticles(diamond shape, ~25 nm) and cassiterite $SnO_2$ nanoparticles(spherical shape, ~10 nm). On the other hand, Sn-doped $TiO_2$ nanoparticles obtained under a high acidic condition showed a crystalline phase corresponding to rutile $TiO_2$. As the Sn content increased, the particle shape changed from rod-like(d~40 nm, 1~200 nm) to spherical(18 nm) with a decrease in the particle size. The peak shift in the XRD results and a change of the c-axis lattice parameter with the Sn content demonstrate that the $TiO_2$ in the rutile phase was doped with Sn. The photocatalytic activity of the $SnO_2$-mixed $TiO_2$ nanoparticles dramatically increased and then decreased when the $SnO_2$ content exceeded 4%. The increased photocatalytic activity is mainly attributed to the improved charge separation of the $TiO_2$ nanoparticles with the $SnO_2$. In the case of Sn-doped $TiO_2$ nanoparticles, the photocatalytic activity increased slightly with the Sn content due most likely to the larger energy bandgap caused by Sn-doping and the decrease in the particle size. The $SnO_2$-mixed $TiO_2$ nanoparticles generally exhibited higher photocatalytic activity than the Sn-doped $TiO_2$ nanoparticles. This was caused by the phase difference of $TiO_2$.

• 공업화학
• /
• 제32권2호
• /
• pp.125-131
• /
• 2021

일반적인 반도체 기반의 광촉매는 물질 고유의 밴드갭 때문에 자외선이나 가시광선에 의해서만 활성화될 수 있고, 태양광 에너지의 약 50%를 차지하는 근적외선 영역의 에너지는 활용할 수 없다. 따라서 기존의 반도체 광촉매의 성능을 향상시키기 위해서는 자외선에서 근적외선에 이르는 넓은 영역에서 더 많은 태양광 에너지를 활용할 수 있어야 한다. 태양광의 근적외선 영역을 활용하기 위해 기존 반도체 광촉매를 업컨버전 나노입자와 결합하는 연구들이 수행되고 있다. 업컨버전 나노입자는 근적외선 광자를 여러 개 흡수하여 자외선이나 가시광선으로 변환하여 광촉매를 활성화할 수 있다. 그리고 반도체 광촉매와 업컨버전 나노입자에 플라즈모닉 금속 나노입자를 함께 결합시키면 태양광에 의한 광촉매 활성을 더욱 향상시킬 수 있다. 본 총설은 업컨버전 나노입자를 이용하여 근적외선 영역의 태양광 에너지가 광촉매의 성능 향상에 기여할 수 있도록 하는 최근의 연구결과를 바탕으로 서술하였다.

• 한국표면공학회지
• /
• 제55권2호
• /
• pp.96-101
• /
• 2022

The effects of the growth temperature on the structural, optical, and morphological properties of BaWO₄:Sm³⁺ phosphor thin films were investigated. The BaWO₄:Sm³⁺ thin films were grown on quartz substrates at several growth temperatures by radio-frequency magnetron sputtering. All the thin films crystallized in a tetragonal structure with a main BaWO₄ (112) diffraction peak. The 830 nm-thick BaWO₄:Sm³⁺ thin films grown at 300 ℃ exhibited numerous polygon-shaped particles. The excitation spectra of BaWO₄:Sm³⁺ thin films consisted of a broad excitation band in the 200-270 nm with a maximum at 236 nm due to the O^2--Sm³⁺ charge transfer and two small bands peaked at 402 and 463 nm, respectively. Under 236 nm excitation, the BaWO₄:Sm³⁺ thin films showed an intense red emission peak at 641 nm due to the ⁴G_5/2→⁶H_9/2 transition of Sm³⁺, indicating that the Sm³⁺ ions occupied sites of non-inversion symmetry in the BaWO₄ host lattice. The highest emission intensity was observed for the thin film grown at 300 ℃, with a 51.8% transmittance and 5.09 eV bandgap. The average optical transmittance in the wavelength range of 500-1100 nm was increased from 53.2% at 200 ℃ to 60.8% after growing at 400 ℃. These results suggest that 300 ℃ is the optimum temperature for growing redemitting BaWO₄:Sm³⁺ thin films.

• 한국재료학회지
• /
• 제33권8호
• /
• pp.344-351
• /
• 2023

Cesium lead iodide (CsPbI₃) with a bandgap of ~1.7 eV is an attractive material for use as a wide-gap perovskite in tandem perovskite solar cells due to its single halide component, which is capable of inhibiting halide segregation. However, phase transition into a photo inactive δ-CsPbI₃ at room temperature significantly hinders performance and stability. Thus, maintaining the photo-active phase is a key challenge because it determines the reliability of the tandem device. The dimethylammonium (DMA)-facilitated CsPbI₃, widely used to fabricate CsPbI₃, exhibits different phase transition behaviors than pure CsPbI₃. Here, we experimentally investigated the phase behavior of DMA-facilitated CsPbI₃ when exposed to external factors, such as heat and moisture. In DMA-facilitated CsPbI₃ films, the phase transition involving degradation was observed to begin at a temperature of 150 ℃ and a relative humidity of 65 %, which is presumed to be related to the sublimation of DMA. Forming a closed system to inhibit the sublimation of DMA significantly improved the phase transition under the same conditions. These results indicate that management of DMA is a crucial factor in maintaining the photo-active phase and implies that when employing DMA designs are necessary to ensure phase stability in DMA-facilitated CsPbI₃ devices.

• Journal of Electrochemical Science and Technology
• /
• 제14권4호
• /
• pp.388-396
• /
• 2023

Photoelectrochemical (PEC) water splitting is a vital source of clean and sustainable hydrogen energy. Moreover, the large-scale H₂ production is currently necessary, while long-term stability and high PEC activity still remain important issues. In this study, a GaN-based photoelectrode was modified by an additional NH₃ treatment (900℃ for 10 min) and its PEC behavior was monitored. The bare GaN exhibited a highly crystalline wurtzite structure with the (002) plane and the optical bandgap was approximately 3.2 eV. In comparison, the NH₃-treated GaN film exhibited slightly reduced crystallinity and a small improvement in light absorption, resulting from the lattice stress or cracks induced by the excessive N supply. The minor surface nanotexturing created more surface area, providing electroactive reacting sites. From the surface XPS analysis, the formation of an N-Ga-O phase on the surface region of the GaN film was confirmed, which suppressed the charge recombination process and the positive shift of E_FB. Therefore, these effects boosted the PEC activity of the NH₃-treated GaN film, with J values of approximately 0.35 and 0.78 mA·cm^-2 at 0.0 and 1.23 V_RHE, respectively, and an onset potential (V_on) of -0.24 V_RHE. In addition, there was an approximate 50% improvement in the J value within the highly applied potential region with a positive shift of V_on. This result could be explained by the increased nanotexturing on the surface structure, the newly formed defect/trap states correlated to the positive V_on shift, and the formation of a GaO_xN_1-x phase, which partially blocked the charge recombination reaction.

• 전자공학회논문지
• /
• 제52권2호
• /
• pp.106-111
• /
• 2015

일반적으로 기준전압 생성기는 쌍안정성을 가지므로 이를 올바른 상태에서 동작시키기 위해서는 적절한 시동회로가 필요하다. 본 논문에서는 저전압 기준전압 발생기를 위한 새로운 시동회로를 제안한다. 제안한 시동회로는 기준전압발생기의 상태를 결정하기 위하여 기준전압 발생기의 BJT에 흐르는 전류를 측정한다. 기준전압발생기가 올바른 상태에 있을 때 이 전류가 가지는 값은 잘 정의되므로 이를 통하여 회로의 상태를 신뢰성 있게 결정할 수 있다. 전류는 내부에 오프셋 전압을 갖는 비교기를 이용하여 측정하였다. 130nm CMOS 공정을 이용하여 설계를 하였으며, 레이아웃에서 추출한 기생 성분을 포함하는 Monte-Carlo 시뮬레이션을 통해 회로의 성능을 검증 하였다. 제안된 시동회로를 사용하는 기준전압발생기에 850mV 이상의 전원 전압이 가해질 경우, 소자에 미스매치가 있더라도 안정적으로 기준전압 생성기가 시동하는 것을 확인하였다.