• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.130-133
• /
• 2002

Polyethylene pressure pipe has been used with a gas pipe material because of workability and stability etc.. Researches on characteristics of polyethylene pressure pipe are carried out, but there are rare. In this study, the tensile test was performed on polyethylene pipe. From the tensile test, AE signals were detected and estimated in real time. Also, the time-frequency analysis of AE signals was analyzed. From test results, PE pipes were displayed typical stress-strain curves oj semi-crystalline polymer. As result analyzed AE signals, could divide stress-strain curves could be divided into four stages. In the elastic region, signals were not detected. Low amplitude distributions of 30-35dB appeared after yielding, and high amplitude distributions of 30-60dB appeared with increased extension. From the time-frequency analysis of AE signals, the frequency band of 100kHz appeared mainly. Also, the frequency band of 300kHz appeared before the necking phenomenon spreads into the whole region, and the frequency band of 500kHz appeared on extension earlier.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.250-255
• /
• 2004

In this paper, we established baseline information and insight on residual stress relief mechanism associated with furnaced and local PWHT(post weld heat treatment) operation. Based on FEM analysis results, we suggested that furnaced PWHT stress relief mechanism was based on creep relaxation and local PWHT stress relief mechanism involved complicated interactions between plasticity and creep. In case of furnaced PWHT, significant stress relaxation was occurred in the early stage of PWHT. In case of local PWHT, stress relaxation magnitude was increased as PWHT time increased. Finally, We have proposed that detailed furnaced and local PWHT procedure, and qualification criteria to support current codes of practices.

• 한국전기전자재료학회논문지
• /
• 제28권11호
• /
• pp.748-751
• /
• 2015

Sound Masking System technology as by sound the same on all bands and artificially generates a constant sound shield People want to hear or recognize the people with the noise generated from the interior of the way. Prevent hearing or prevent recognition by using the technology to control the audible frequency band Continue to emit constant and uniform shielding sound audible frequency band Even the security content of speech (20 Hz~20 KHz). That interception laser eavesdropping, internal solicitations, during recording Or delay the decoding was a result of the effect of interference calculated Experience noise disturbance index is applied around the Stress Index is the average index is 10.16 was a luxury for the average index is then applied to the index 3.07 Noise is significantly lower stress level has improved noise conditions.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.208-213
• /
• 2004

Methods for estimation of the effective stress intensity factor range (${\Delta}K_{eff}$) are evaluated for narrow and wide band random loading crack growth test data of 2024-T351 aluminum alloy. Three methods of determining $K_{op}$, visual measurement, ASTM offset compliance method, and the neural network method proposed by Kang and Song, and three methods of estimating ${\Delta}K_{eff}$, conventional, the 2/PI0 and 2/PI methods proposed by Donald and Paris, are compared in a quantitative manner by using the results of fatigue crack growth life prediction under random loading. For all $K_{op}$ determination methods discussed, the 2/PI0 and 2/PI methods of estimating ${\Delta}K_{eff}$ provide better results than conventional method for narrow and wide band random loading data.

• 한국생산제조학회지
• /
• 제9권4호
• /
• pp.25-33
• /
• 2000

The reorientations of the atoms by frictional shear deformation at the surface induce cracks at the boundary of the grain. The cracks grow and propagate in regions where the hydrostatic component of stress is least compressive because the compressive component restores the cracks by three-dimensional crystallizing $\pi$-bondings. The materials with Lder's band have very small amount of wear at the initial state. It suggests that initial frictional shear deformation be consumed to the formation of the Lder's band. The average wear amounts of the materials increase very steeply as the øu the stress-strain ratio at the ultimate point, decreases.

• Transactions on Electrical and Electronic Materials
• /
• 제18권1호
• /
• pp.16-20
• /
• 2017

A RF-MEMS (radio-frequency microelectromechanical-system) based DPDT (double pole double throw) switch for the Ku band has been designed and analyzed for this article. The switch topology is based on the FG-CPW (finite ground-coplanar waveguide) configuration of a microstrip-transmission line. An FEM-based multiphysics solver is used for the evaluation of the spring constant, stress distribution, and pull-in voltage regarding the requirements of the switch-beam unit. The electromagnetic performance of the switch is investigated for a $675{\mu}m$ thick silicon substrate. For the operational frequency of 14.5 GHz, an insertion loss better than -0.3 dB, a return loss better than -40 dB, and input/output- and output-port isolations better than -35 dB are achieved for the switching unit.

• 한국전기전자재료학회논문지
• /
• 제16권3호
• /
• pp.181-185
• /
• 2003

Influence of post gate oxidation anneal on Negative Bias Temperature Instability (NBTI) of PMOSFE has been investigated. At oxidation anneal temperature raised above 950$^{\circ}$C, a significant improvement of NBTI was observed which enables to reduce PMO V$\_$th/ shift occurred during a Bias Temperature (BT) stress. The high temperature anneal appears to suppress charge generations inside the gate oxide and near the silicon oxide interface during the BT stress. By measuring band-to-band tunneling currents and subthreshold slopes, reduction of oxide trapped charges and interface states at the high temperature oxidation anneal was confirmed.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제6권1호
• /
• pp.51-61
• /
• 2006

Failure analyses were conducted on a crank shaft and a chock liner by using X-ray diffraction, optical microscopy and SEM/EDS techniques. In the crank shaft, a crack developed where a maximum tensile stress coincided with band structure formed by hot forging. The maximum tensile stress was observed to originate from volume expansion during high frequency induction heat treatment and the band structure to develop between upper and lower dies during hot forging. In the chock liner, the wear mechanism varied with the chemical affinity and hardness of liner material relative to friction pair of housing liner. Brass of low chemical affinity and hardness compared to housing liner showed uniform adhesive wear. STS 304 and STS 420J2 of high chemical affinity showed galling and scoring respectively.

• 한국전산구조공학회논문집
• /
• 제24권3호
• /
• pp.275-281
• /
• 2011

일반적으로 인장 시험에 주로 사용되는 납작한 형태의 금속 재료에 천천히 인장력을 가하고 그 힘을 증가시키면 어느 순간에 루더스 밴드(Luders band)라고 불리는 소성 변형의 띠가 갑자기 발생한다. 이 띠들은 일정 각도를 가지고 평행하게 발생하며, 여러 연구자들에 의해 특정 경계조건에 대하여 이 띠가 발생하는 조건과 그 각도에 대한 많은 연구가 선행되어 왔다. 본 연구에서는 평면 응력 조건에서 이루어진 Thomas(1961)의 연구를 기반으로 하고 $J_2$ 소성 변형 조건, 힘의 평형방정식, 그리고 구성방정식을 이용하여 평면 변형 조건에서 발생하는 밴드의 각도를 해석적으로 유도하였다. 이 결과는 음향텐서를 이용한 기존의 연구 결과와 일치함을 확인하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 연약지반처리위원회 학술세미나
• /
• pp.62-70
• /
• 1999

Artesian pressure exists in Yangsan site, the maximum value of which has been measured as high as 5 t/m$^2$. This paper deals with the prediction of consolidation settlement for the site with artesian pressure. The consolidation settlement at the site has been accelerated using vertical band drains. Since the artesian pressure gives lower effective stress than a static condition, its effect should be considered in the settlement prediction. This case study shows that the prediction of settlement and pore pressure dissipation agrees well with the measurements, when considering the artesian effect.