• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.74-79
• /
• 2000

In an attempt to estimate the wetting properties of wettable metal layers by wetting balance method, an analysis of wetting curves of the coating layer was performed. Based on the analysis, wetting properties of UBM-coated Si-plate were estimated by the new wettability indices. The wetting curves of the one and both sides-coated UBM layers have the similar shape and show the similar tendency to the temperature. So the wetting property estimation of one side coating is possible with wetting balance method. For UBM of Si-chip, Cr/Cu/Au UBM is better than Ti/Ni/Au in the point of wetting time. At general reflow temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) is better than that of few melting point ones(Sn-Bi, Sn-In).The contact angle of the one side coated plate to the solder can be calculated from the farce balance equation by measuring the static state force and the tilt angle.

• 대한치과보철학회지
• /
• 제32권3호
• /
• pp.378-395
• /
• 1994

The purpose of this study was to investigate the effect of various metal surface treatments and adhesive systems on the flexural bond strength of composite resin to Au-Ag-Cu-Pd alloy. The specimens were divided into nine groups by the combinations of surface treatment methods and adhesive systems. The types of surface treatment in this study were alumina blasting only, alumina blasting-Sn plating, alumina blasting-heating and three kinds of adhesive system used in this study were Silicoater system(Heraeus Kulzer GmbH,Germany), Superbond C & B(Sun Medical Co.,Ltd.,Japan) and Cesead opaque primer(Kurary Co.,Ltd.,Japan). After surface treatments and adhesive systems were applied, each specimen was built up with Dentacolor composite resin (Heraeus Kulzer GmbH,Germany). Four-point flexural bond strength was measured by Instron universal testing machine (Model 4301,U.S.A.) and modes of failure were observed by SEM(JEOL,SSM-840A,Japan). The obtained results were as follows: 1. The group that was bonded with Superbond C & B after alumina blasting-heating shelved the highest bond strength with significant difference among the groups, except the group with Cesead opaque primer after alumina blasting-Sn plating(P<0.05). 2. In the groups bonded with Cesead opaque primer, there was significant difference only in the bond strength between the alumina blasting-Sn plating group and alumina blasting group, where the former showed a higher bond strength(P<0.05). 3. In the groups bonded with Silicoater system, there were no significant differences in bond strength regardless of the surface treatment method(P<0.05). 4. In SEM evaluation, the groups of high bond strength, especially bonded with Superbond C & B after alumina blasting-heating and Cesead opaque primer after alumina blasting-Sn plating, revealed mainly cohesive-adhesive failure, whereas the others showed the tendency of adhesive failure.

• 센서학회지
• /
• 제29권6호
• /
• pp.407-411
• /
• 2020

In this study, we propose an array-type gas sensor with high selectivity and response using multiple oxide semiconductors. The sensor array was composed of SnO₂ and In₂O₃, and the detection characteristics were improved by using Pt, Au, and Pd catalysts. All samples were deposited directly on the Pt interdigitated electrode (IDE) through the e-beam evaporator glancing angle deposition (GAD) method. They grew in the form of well-aligned nanorods at off-axis angles. The prepared SnO₂ and In₂O₃ nanorod samples were exposed to CH₃COCH₃, C₇H₈, and NO₂ gases in a 300℃ dry condition. Au-decorated SnO₂, Au-decorated In₂O₃, and Pd-decorated In₂O₃ exhibited high selectivity for CH₃COCH₃, C₇H₈, and NO₂, respectively. They demonstrated a high detection limit of the sub ppb level computationally. In addition, measurements from each sensor were executed in the 40% relative humidity condition. Although there was a slight reduction in detection response, high selectivity and distinguishable detection characteristics were confirmed.

• 마이크로전자및패키징학회지
• /
• 제29권2호
• /
• pp.73-79
• /
• 2022

본 연구에서는 최근 저온접합 소재로 각광받고 있는 Ga과 대표적인 전극 물질인 Cu와의 반응연구를 실시하여 저온 솔더링 적용시 필요한 정보들을 확인하고자 하였다. 80-200℃ 온도범위에서 Ga과 Cu/Au 기판을 반응시켜 계면반응 및 금속간화합물(IMC) 성장을 관찰하고 분석하였다. 반응계면에서 성장하는 주요한 IMC는 CuGa₂ 상이었으며 그 상부에는 작은 입자크기를 가지는 AuGa₂ IMC 그리고 하부에는 얇은 띠 형상의 Cu₉Ga₄ IMC가 형성되었다. CuGa₂ 입자들은 scallop 형상을 보이며 Cu₆Sn₅ 성장의 경우와 비슷하게 반응시간이 증가함에 따라서 큰 형상변화없이 입자 크기가 증가하였다. CuGa₂ 성장기구를 분석한 결과 120-200℃ 온도범위에서 시간지수는 약 3.0으로 산출되었고, 활성화에너지는 17.7 kJ/mol로 측정되었다.

• 한국재료학회지
• /
• 제10권12호
• /
• pp.799-806
• /
• 2000

63Sn-37Pb에 Cu$_{6}$Sn$_{5}$를 분산시킨 760$\mu\textrm{m}$크기의 솔더범프를 Au(0.5$\mu\textrm{m}$)/Ni(5$\mu\textrm{m}$)/Cu(27$\pm$20$\mu\textrm{m}$) BGA 기판에 스크린)/Ni(5im)/Cu(27:201m) B3GA 기판에 스크린 프린팅법으로 제조하여, 리플로우 피크온도 유지시간, 15$0^{\circ}C$ 시효처리 시간에 따른 전단강도를 분석하였다. Cu$_{6}$Sn$_{5}$를 첨가한 솔더범프는 피크온도에서 30초간 유지시에는 63Sn-37Pb 솔더범프보다 높은 전단강도를 나타내었으나, 피크온도 유지시간을 60초 이상으로 증가시킴에 따라 전단강도가 63Sn-37Pb 솔더범프보다 저하하였다. 전단시험 후 솔더범프의 파단면은 초기에 전단 균열의 점진적인 전파에 의해 발생된 파괴부위와 점진적 균열전파에 의한 면적 감소로 솔더범프가 급격히 떨어져 나가면서 발생한 파괴부위로 구분할 수 있었다 피크온도 유지시간, 15$0^{\circ}C$ 시효처리 시간 및 Cu$_{6}$Sn$_{5}$ 첨가량에 무관하게 점진적 파괴모드에 의한 균열 전파길이가 증가할수록 솔더범프의 전단강도가 감소하였다.감소하였다.

• 한국표면공학회지
• /
• 제36권5호
• /
• pp.386-392
• /
• 2003

The electroplating process for a solder bump which can be applied for a flip chip was studied. Si-wafer was used for an experimental substrate, and the substrate were coated with UBM (Under Bump Metallization) of Al(400 nm)/Cu(300 nm)Ni(400 nm)/Au(20 nm) subsequently. The compositions of the bump were Sn-Cu and eutectic Sn-Pb, and characteristics of two bumps were compared. Experimental results showed that the electroplated thickness of the solders were increased with time, and the increasing rates were TEX>$0.45 <\mu\textrm{m}$/min for the Sn-Cu and $ 0.35\mu\textrm{m}$/min for the Sn-Pb. In the case of Sn-Cu, electroplating rate increased from 0.25 to $2.7\mu\textrm{m}$/min with increasing current density from 1 to 8.5 $A/dm^2$. In the case of Sn-Pb the rate increased until the current density became $4 A/dm^2$, and after that current density the rate maintains constant value of $0.62\mu\textrm{m}$/min. The electro plated bumps were air reflowed to form spherical bumps, and their bonded shear strengths were evaluated. The shear strength reached at the reflow time of 10 sec, and the strength was of 113 gf for Sn-Cu and 120 gf for Sn-Pb.

• 마이크로전자및패키징학회지
• /
• 제10권4호
• /
• pp.39-46
• /
• 2003

플립칩용으로 Sn-Cu 공정 솔더 범프를 전해도금을 이용하여 제조하고 특성을 연구하였다. Si 웨이퍼 위에 UBM(Under Bump Metallization)으로 Al(400 nm)/Cu(300 nm)/Ni(400 nm)/Au(20 nm)를 전자빔 증착기로 증착하였다. 전류밀도가 1 A/d$\m^2$에서 8 A/d$\m^2$으로 증가함에 따라 Sn-Cu 솔더의 도금속도는 0.25 $\mu\textrm{m}$/min에서 2.7 $\mu\textrm{m}$/min으로 증가하였다. 이 전류밀도의 범위에서 전해도금된 Sn-Cu 도금 합금의 조성은 Sn-0.9∼1.4 wt%Cu의 거의 일정한 상태를 유지하였다. 도금 전류밀도 5 A/d$\m^2$, 도금시간 2hrs, 온도 $20^{\circ}C$의 조건에서 도금하였을 때, 기둥 직경 약 120 $\mu\textrm{m}$인 양호한 버섯 형태의 Sn-Cu 범프를 형성할 수 있었다. 버섯형 도금 범프를 $260^{\circ}C$에서 리플로우 했을 때 직경 약 140 $\mu\textrm{m}$의 구형 범프가 형성되었다. 화학성분의 균일성을 분석한 결과 버섯형 범프에서 존재하던 범프내 Sn 등 성분 원소의 불균일성은 구형 범프에서는 상당 부분 해소 되었다.

• 마이크로전자및패키징학회지
• /
• 제27권1호
• /
• pp.1-7
• /
• 2020

The backside metallization process is typically used to attach a chip to a lead frame for semiconductor packaging because it has excellent bond-line and good electrical and thermal conduction. In particular, the backside metal with the Ag/Sn/Ag sandwich structure has a low-temperature bonding process and high remelting temperature because the interfacial structure composed of intermetallic compounds with higher melting temperatures than pure metal layers after die attach process. Here, we introduce a die attach process with the Ag/Sn/Ag sandwich structure to apply commercial semiconductor packages. After the die attachment, we investigated the evolution of the interfacial structures and evaluated the shear strength of the Ag/Sn/Ag sandwich structure and compared to those of a commercial backside metal (Au-12Ge).

• 마이크로전자및패키징학회지
• /
• 제15권4호
• /
• pp.1-7
• /
• 2008

본 실험에서는 두가지 리플로 시스템에 따라 솔더 범프 내에 생성되는 금속간 화합물의 성장거동에 대하여 연구하였다. 산화막이 증착된 Si 기판 위에 직류 마그네트론 스퍼터링을 이용하여 Ti(50 nm), Cu($1{\mu}m$), Au(50 nm), Ti(50 nm)의 박막을 형성한 후, 전해 도금을 이용하여 $5{\mu}m$두께의 Cu 범프와 $20{\mu}m$ 두께의 Sn 범프를 형성하였다. 급속열처리장치(RTA)와 일반 리플로를 이용하여 전해 도금으로 형성된 Sn($20{\mu}m$)/Cu($5{\mu}m$) 범프를 동일한 온도에서 각각 리플로 공정을 진행한 결과, 급속열처리장치를 이용하여 리플로를 할 때, 플럭스를 사용하지 않고 범프로 형성할 수 있었으며, 솔더 계면에 형성된 금속간 화합물이 일반 리플로의 경우보다 더 얇게 형성되었다.

• Journal of Welding and Joining
• /
• 제23권4호
• /
• pp.34-40
• /
• 2005

There have been numerous approaches to examine the bonding strengths of solder joints. However, despite the technical and practical limitations, the precedent test methods such as the ball shear and ball pull tests are being used in industrial applications. In this study, the optimum jaw pressure with the modified protrusion jaw was introduced in order to obtain higher successful rate f3r ball pull testing. Furthermore, the pull strengths and fracture modes of Sn-8Zn-3Bi, Sn-4Ag-0.7Cu, and Sn-37Pb eutectic solder after isothermal aging tests ($100^{\circ}C,\;150^{\circ}C$), were evaluated with the protrusion jaw. The pull strength-displacement hysteresis curves and fracture surfaces were carefully investigated to evaluate the correlation between the pull strengths and the fracture modes of each solder. In conclusion, it is verified that Au-Zn IMCs (Intermetallic Compounds) have a detrimental effect on the pull strengths and changed fracture modes of Sn-8Zn-3Bi solder. Meanwhile, the microstructure transformation influences the degradation of pull strengths of Sn-4Ag-0.7Cu and Sn-37Pb solders.