• 소성∙가공
• /
• 제23권4호
• /
• pp.199-205
• /
• 2014

The current study examines the effect of the analytical parameter values on the theoretical forming limit diagram (FLD) based on the Marciniak-Kuczynski model (M-K model). Tensile tests were performed to obtain stress-strain curves and determine the anisotropic properties in the rolling, transverse and diagonal direction of SPCC sheet materials. The experimental forming limit curve for SPCC sheet material was obtained by limiting dome stretching tests. To predict the theoretical FLD based on the M-K model, the Hosford 79 yield function was employed. The effects of three analytical parameters - the exponent of the yield function, the initial imperfection parameter and the fracture criterion parameter - on the M-K model, were examined and the results of the theoretical FLD were compared to the experimentally measured FLD. It was found that the various analytical parameters should be carefully considered to reasonably predict the theoretical FLD. The comparison of the acceptable forming limit area between the theoretical and experimental FLD is used to compare the two diagrams.

• 전기학회논문지
• /
• 제59권2호
• /
• pp.318-327
• /
• 2010

This paper deals with analysis on dynamic characteristic and circuit parameter of linear switched reluctance motor by electromagnetic analytical method. Above all, using space harmonic method, which is electromagnetic method, the air-gap flux density is analyzed in the both align and unaign positions, and the inductance profile, force characteristic and resistance per phase are calculated by means of the process. The validity of the analyzed results are demonstrated by the finite element method(FEM) and manufacture of the prototype machine. Second, the dynamic simulation is analyzed by the use of circuit parameters derived from analytical method, and the operating system of the prototype machine is manufactured to demonstrated the validity of simulation analysis. As a result, it is considered that the characteristic equation suggested in this paper will contribute to the design, analysis and application of LSRM.

• 전기의세계
• /
• 제29권1호
• /
• pp.53-57
• /
• 1980

The analytical treatment for a terminal cost problem of a distributed reactor with a small singular parameter is presented. The inverse of the neutron velocity is regarded as a singular parameter, and the model, adopted for simplicity, is a cylindrically symmetrical reactor. The Helmholtz mode expension is used for the application of the optimal theory for lumped parameter systems to the spatially distributed parameter system. The closed-form solution is explicitely obtained for machine calculation.

• 소음진동
• /
• 제9권5호
• /
• pp.891-898
• /
• 1999

The purpose of Superconducting Magnetic Bearing Flywheel Energy Storage System (SMB-FESS) is to store unused nighttime electricity until it is needed during daytime. An analytical model of the SMB-FESS is necessary to identify the system behavior. At first, we have to model the superconducting magnetic bearing. Modeling the SMB is same as estimating the bearing parameter. The theoretical modal parameter is calculated through the equation of motion and the experimental modal parameter is estimated through the impact testing (modal testing). The bearing parameter is searched by using the non-linear least square method until the theoretical result corresponds to the experimental result. The suggested modeling method is verified by comparing experimental and analytical frequency response function.

• 대한건축학회논문집:구조계
• /
• 제34권1호
• /
• pp.27-32
• /
• 2018

This work provides the analytical methods to represent the updated form of stiffness or flexibility matrices using the measurements of the first few natural frequencies and the corresponding mode shapes. This study derives the mathematical forms on the variance of stiffness or flexibility matrices to minimize the performance index in the satisfaction of the eigen-function including the residual force depending on the measured data. The proposed methods can be utilized in detecting damage and updating the parameter matrices deviated from the analytical parameter matrices. The validity of the proposed methods is investigated in a numerical experiment of truss structure and the numerical results of stiffness-based and flexibility-based methods are compared. The sensitivity to the external noise is also examined for applying to the practical work.

• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1801-1812
• /
• 2006

In this paper, a 4-wheel vehicle model including the effects of tire slip was considered, along with variable parameter sliding control, pushrod force as the end control parameter, and an antilock sliding control, in order to improve the performance of the vehicle longitudinal response. The variable sliding parameter is made to be proportional to the square root of the pressure derivative at the wheel, in order to compensate for large pressure changes in the brake cylinder. A typical tire force-relative slip curve for dry road conditions was used to generate an analytical tire force-relative slip function, and an antilock sliding control process based on the analytical tire force-relative slip function was used. A retrofitted brake system, with the pushrod force as the end control parameter, was employed, and an average decay function was used to suppress the simulation oscillations. Simulation results indicate that the velocity and spacing errors were slightly larger than the results that without considering wheel slip effect, the spacing errors of the lead and follower were insensitive to the adhesion coefficient up to the critical wheel slip value, and the limit for the antilock control on non-constant adhesion road condition was determined by the minimum of the equivalent adhesion coefficient.

• Journal of Electrical Engineering and Technology
• /
• 제4권3호
• /
• pp.401-404
• /
• 2009

A simple analytical expression for a current gain of IGBT is derived in terms of the device parameters as well as a gate length dependent parameter, which allows for the determination of the current components of the device as a function of its gate length. The analytical results are compared with those from simulation results. A good agreement is found.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권4호
• /
• pp.155-162
• /
• 1999

This paper presents a generation of analytical fragility curves for bridge. The analytical fragility curves are constructed on the basis of nonlinear dynamic analysis. Two-parameter lognormal distribution functions are used to represent the fragility curves with the parameters estimated by the maximum likelihood method. To demonstrate the development of analytical fragility curves, two of representative bridges with a precast prestressed continuous deck in the Memphis. Tennessee area are used.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제18권3호
• /
• pp.257-268
• /
• 2014

The objective of the present study is to investigate thermal diffusion and radiation effects on unsteady MHD flow past a linearly accelerated vertical porous plate with variable temperature and also with variable mass diffusion in presence of heat source or sink under the influence of applied transverse magnetic field. The fluid considered here is a gray, absorbing/emitting radiation but a non-scattering medium. At time t > 0, the plate is linearly accelerated with a velocity $u=u_0t$ in its own plane. And at the same time, plate temperature and concentration levels near the plate raised linearly with time t. The dimensionless governing equations involved in the present analysis are solved using the closed analytical method. The velocity, temperature, concentration, skin-friction, the rate or heat transfer and the rate of mass transfer are studied through graphs in terms of different physical parameters like magnetic field parameter (M), radiation parameter (R), Schmidt parameter (Sc), Soret number (So), Heat source parameter (S), Prandtl number (Pr), thermal Grashof number (Gr), mass Grashof number (Gm) and time (t).

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제7권2호
• /
• pp.88-93
• /
• 2007

In this paper, a simple and improved noise parameter model of RF MOSFETs is developed and verified. Based on the analytical model of channel thermal noise, closed form expressions for four noise parameters are developed from proposed equivalent small signal circuit. The modeling results show a excellent agreement with the measured data of $0.13{\mu}m$ CMOS devices.