• Journal of Electrical Engineering and Technology
• /
• v.11 no.5
• /
• pp.1449-1456
• /
• 2016

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.5
• /
• pp.1176-1181
• /
• 1995

Microdrilling is one of the most difficult operations because of the poor chip discharge and the weakness of tool. This study is concerned about the development of a microdrilling monitoring system that is useful for minimizing the tool breakage and enhancing the machinability in the air spindle based microdrilling. The system is composed of a drilling state detection unit and an adaptive step-feed control unit that controls the micro-stepping motor driven spindle axis. Drilling states such as overload, tood breakage are recognized by the change of the air spindle speed which is measured via the reflective photo sensor. Based on the monitoring results, the adaptive step-feed control algorithm adjusts the step increment to keep the decrease of spindle speed within a specified range. The results of evaluation tests have shown that the developed system is very effective to prevent the breakage of microdrill and improves the productivity in comparison with the conventional microdrilling.

• Korean Journal of Veterinary Research
• /
• v.14 no.2
• /
• pp.237-241
• /
• 1974

A number of chemotherapeutic agents, namely antibiotics, sulfonamides and nitrofuran derivatives have been used, as a fred additive, for the purposes of growth improvement of chicken, increase of feed efficiency, decrease of animal mortality, and disease prevention. In these experiments, furamizole which is one of nitrofuran derivatives and feed additive was test, in field, its antibacterial activity against Mycoplasma gallisepticum causing air sac disease, its effect on pullorum disease control, its effect on the lowering the mortality of chicken and finally the increase of feed efficiency. Throughout the studies, furamizole, in concentration of 0.025% in feed fed to baby chicken continuously resulted as following: 1. Tested chicken showed no avian mycoplasma infection compared to 3.7% outbreak in control chicken. 2. Tested chicken showed a low degree of outbreak of pullorum disease. However, its outbreak was much more surpresed compared to that of control chicken. 3. Total mortality rate of 5.5% and 30.8% were obtained in test and control chicken respectively. 4. Feed efficiency were 2.83 and 2.97 in test and control chicken respectively.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.3
• /
• pp.10-13
• /
• 2016

The wet-air oxidation in gravity pressure reactor is effective for organic waste treatment with energy saving under high pressure and high temperature. But its oxidation control is difficulty because its multi-phase flow characteristics is very complicated. The flow characteristics of an oxidizer feed section in the gravity pressure reactor were investigated using numerical method which are verified by comparison with experimental results. In this study, the results showed that the flow rate of oxidizer have an effect on the generation of bubble around feed section.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.994-1003
• /
• 2016

Two major obstacles in the utilization of electrical vehicles are their price and range. The collaboration of direct torque control (DTC) with induction motor (IM) is preferred for its low cost, easy implementation, and parameter independency. However, in terms of edges, the method has drawbacks, such as variable switching frequency and undesired current harmonic distortion. These drawbacks result in acoustic noise, reduced efficiency, and electromagnetic interference. A feed-forward approach for stator-flux-oriented DTC with space vector pulse-width modulation is presented in in this paper. The outcome of the proposed method is low current harmonic distortion with fixed switching frequency while preserving the torque performance and simple application feature of basic DTC. The method is applicable to existing and forthcoming IM drive systems via software adaptation. The validity of the proposed method is confirmed by simulation and experimental results.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.131-134
• /
• 2015

국내 천연가스 열량제도를 현행 표준 열량제 $10,400kcal/Nm^3(43.54MJ/Nm^3)$에서 중간 조정기간을 두고 2012.07.01부터는 최저 $10,100kcal/Nm^3(42.28MJ/Nm^3)$을 유지하고 2015년 이후 $9,800(41.1MJ/Nm^3){\sim}10,600kcal/Nm^3(44.4MJ/Nm^3)$ 열량범위제도로 변경 추진되고 있다. 산업현장에서 열량변동을 측정하여 공연비 제어기술을 개발하고자 60ton Al 용해로에 열량대응기술 개발을 위한 내용으로 열량측정시스템설치 및 열량 값과 연계하여 공연비 제어기술개발연구 내용으로 결과는 다음과 같다. 단순히 표준열량으로 에 맞춰 프로그램된 제어로직에 열량변동에서 검출된 신호를 이용하여 연료보정 값을 추가한 로직을 재구성할 필요가 있다. 이 혀장의 경우는 용탕의 온도가 목표온도 근처까지 올리기가 어려워진 상황으로 주로 공급열량 저열량화에 따른 과잉공기영향으로 온도상승이 어려워 보이며 적절한 공연비로 최적화 되면 이러한 문제가 개선되리라 생각된다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.6
• /
• pp.1122-1127
• /
• 2001

This paper proposed a speed adaptive control system with load torque observer and feed-forward compensation using neural network for air compressor system driven an induction motor. The motor receive impact load change under the influence of piston movement of up and down, and so it difficult to obtain good speed control characteristics. With real-time adjusting control gain estimated in neural network, control characteristics of motor is improved. The validity of the proposed system is confirmed through the theoretical analysis and computer simulation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.397-400
• /
• 2001

This paper proposed a speed adaptive control system with load torque observer and feed-forward compensation using neural network for air compressor system driven an induction motor. The motor receive impact load change under the influence of piston movement of up and down, and so it difficult to obtain good speed control characteristics. With real-time adjusting control gain estimated in neural network, control characteristics of motor is improved. The validity of the proposed system is confirmed through the theoretical analysis and computer simulation.

• Proceedings of the KIEE Conference
• /
• 2008.04a
• /
• pp.223-224
• /
• 2008

초초임계압 화력발전 제어계통 설계와 관련하여 보일러 제어시스템의 기본 요건인 제어전략을 구현하기 위해 현재 표준화력 500MW 제어시스템과 제어로직을 기반으로 1000MW급에서 필요로 하는 새로운 구조의 제어에 요구되는 제어전략에 대해 각종 제어 운전 모드의 구성과 각 운전 모드에서의 제어전략을 개발하고 있다. 최신제어시스템에서 중요하게 취급되는 자동 플랜트 제어(Automatic Plant Control, APE)의 각종 제어전략 구성에 중점을 두고 있으며 Unit Master Control, Boiler Master Control, Turbine blaster Control, Throttle Pressure Control, Fuel/Air Master Control, Forced Draft Fan Control, Induced Draft Fan Control, Primary Air Fan, Feed Water Master Control, Super Heater/Reheater Steam Temp Control 등의 제어전략을 논하고, 실제 프로세스 응단특성 파악을 위해 국내 신규발전소를 방문하여 수집한 프로세스 응답시험 결과와 특성을 분석하고 USC에 적용하기위한 보일러 제어전략에 대해 논하고자 한다.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.2
• /
• pp.90-95
• /
• 1999

The study on the fermented feeds production of garbages have been conducted to determine the optimum operation condition. The process variables considered for this study were initial air flow rate and temperature control. The results showed that optimum air requirement was $4{\ell}-air/min{\cdot}kg-$ garbages on dry weight basis which is equal to $0.8{\ell}-air/min{\cdot}kg-$ garbages on the basis of 80% moisture content. The optimum initial temperature control in the reactor was $40^{\circ}C$. Crude fiber content of fermented final byproducts were higher than feedstuffs standard for pig breeding and consequently final byproducts had to mix with single-component feed.