• 한국전기전자재료학회논문지
• /
• 제36권3호
• /
• pp.255-260
• /
• 2023

In order to spread LED lighting, LED lighting technology directly driven by alternating current (AC) commercial power has recently been introduced. Since current does not flow at a voltage lower than the threshold voltage of the LED, a non-conductive section occurs in the current waveform, and the higher the threshold voltage of the LED, the more discontinuous current waveforms are generated. In this paper, multi-LED modules are connected in series so that the threshold voltage can be adjusted according to the number of LED modules. A small number of LED modules are driven at a low instantaneous rectified voltage, and a large number of LED modules are driven at a high instantaneous rectified voltage to lengthen the overall lighting time of AC-LED lighting, thereby minimizing the luminance deviation of AC-LED lighting. In addition, the load current flowing through the LED module is adjusted to be the same as the design current even at the maximum rectified voltage higher than the design voltage, so that the light brightness of the LED module is kept constant. Therefore, even if the rectified voltage applied to the LED module changes, the AC-LED lighting in which the light brightness is constant and the luminance deviation is minimal has been realized.

• 전기학회논문지P
• /
• 제67권2호
• /
• pp.63-69
• /
• 2018

In this paper, the operation principle of a bi-directional switch type resonant AC link snubber circuit was described, together with the practical design procedure, which employs in the proposed power module bridge package type resonant AC link snubber. The novel prototype of power module bridge package type resonant AC link snubber-assisted voltage type sinewave soft switching PWM inverter using IGBT power module was demonstrated herein. It was verified that both the auxiliary power switches in this resonant AC link snubber circuit and the main power switches commutate under the condition of soft switching commutation principle. In addition, the power losses of the new soft switching inverter treated here were analyzed by implementing the experimental data of the IGBT and diode v-i characteristics in addition to switching power loss characteristics into our original computer simulation software developed by the authors. Then, the voltage type sinewave soft switching PWM inverter was high efficiency than that of hard switching PWM inverter, along with performance operation waveforms. In the future, the comparative feasibility study of power module bridge type resonant AC link snubber and its related soft switching inverter in addition to the other types resonant snubber assisted soft switching inverter should be done from a practical point of view.

• 대한전자공학회논문지SD
• /
• 제40권11호
• /
• pp.29-36
• /
• 2003

이 논문에서는, 2D-DCT, 양자화, AC/DC 예측블록, 스캔 변화, 역 양자화, 2D-IDCT로 이루어진 DCTQ 모듈의 효율적인 구조를 제안한다. 이 모듈은 1064 cycle 안에 매크로블록을 처리할 수 있도록 설계하였으며, MPEG-4 Video codec에서 30frame 의 CIF 영상에 대하여 동시에 encoder와 decoder를 처리할 수 있다. 단지 하나의 1D-DCT와 IDCT core 가 2-D DCT/IDCT 대신에 사용되며, 1 bit serial 분산산술방식을 이용하여 1-D DCT/IDCT를 구현하였다. 또한 파워소모를 줄이기 위해 움직임 예측에서 얻을 수 있는 SAE 값을 이용한 DCT와 양자화 모듈을 동작을 시키지 않는 방식을 제안하였다. 그리고 AC/DC 예측방법을 위한 메모리를 줄일 수 있도록 AC/DC 예측블록을 위한 메모리 구조 및 접근방법을 제안하였다. 그 결과, 하드웨어의 재 사용성이 놀아지고 파워소모가 작아짐을 알 수 있었다. 제안된 설계는 27㎒로 돌아가며, 실험결과 DCT와 IDCT 는 IEEE 기준을 만족함을 알 수 있었다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 추계학술대회 논문집
• /
• pp.103-104
• /
• 2014

This paper presents design method of 250[W] grid connected PV-AC module with decoupling and energy storage functions to select optimized passive elements for stable operation. The validity of design of optimized elements is verified by simulation results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.536-537
• /
• 2012

In this paper, current-fed soft switching push-pull converter for Photovoltaic AC module was proposed. The theoretical analysis of the proposed converter is verified by simulation and experiment.

• 한국산학기술학회논문지
• /
• 제18권4호
• /
• pp.504-510
• /
• 2017

본 논문은 소형 가전기기를 위한 AC DC 파워모듈 설계를 제시하고 효율과 신뢰성 및 안정성 특성을 나타낸다. 제안하는 파워모듈은 PCB 테스트보드에서 PWM 제어 IC 칩, 파워모스 소자, 트랜스포머, 각종 수동소자 (저항, 커패시터, 인덕터)를 사용하여 제작하였다. 본 논문에서 제시한 AC DC 파워모듈 회로 시뮬레이션 결과를 토대로 측정한 실험에서 입력전압은 상용전원 전압 220 V (RMS), 주파수 60 HZ의 교류전압(VAC : Voltage alternating current)을 사용 하였으며, 출력전압, OCP (over current protection), EMI(electromagnetic interference), PWM 신호 펄스, 효율 측정, 패키징 여부에 따른 발열측정 등을 실시하였다. 또한 파워모듈의 온도에 따른 특성변화와 트랜스포머 기준으로 1차측의 회로와 2차측 회로의 절연상태 확인을 하기 위한 내전압 테스트 등의 신뢰성테스트를 실시하였다. 효율 및 신뢰성 측정결과, AC DC 파워 모듈이 5 V의 출력전압, 200 mV의 리플, 약 73 %의 효율, 온도 약 $80^{\circ}C$ 까지 안정적으로 동작함을 확인하였으며, 4.2 kV의 크기로 60초 동안 견디는 내압 성능을 보였다.

• 한국정보전자통신기술학회논문지
• /
• 제2권1호
• /
• pp.11-15
• /
• 2009

본 연구에서 전원이 공급되는 의료기기들에서 공통적으로 사용되며, 성능, 안전성과 신뢰성 측면에서 기존 전원모듈보다 우수한 250 W SMPS방식을 적용한 의료용 전원모듈의 개발하였다. SMPS의 특성상 AC전원의 50 ~ 60 Hz 라인 주파수를 DC로 변환하는 회로의 설계와 높은 주파수로 변경하기 위한 전자회로로 구성하였고, 완전한 방사노이즈 흡수회로를 구성하여 의료기기 오동작을 방지하기 하도록 설계하였다. SMPS 전원모듈은 의료기기뿐만 아니라 PC, 가정용 기기 및 전자 교환기 등의 제품에도 확대 적용이 가능하다.

• 전력전자학회논문지
• /
• 제19권5호
• /
• pp.391-398
• /
• 2014

This paper presents a resonant step-down DC/DC converter to reduce the voltage stresses of a 3-phase inverter module under the three-phase AC utility line condition. Under this condition, a conventional 3-phase inverter module suffers from high voltage stresses as a result of the high rectified DC link voltage; hence, a high-cost high-voltage-rating inverter module must be used. However, using the proposed converter, a low-cost low-voltage-rating inverter module may be adopted to drive the motor even under the 3-phase AC line condition. The proposed converter, which can be realized with small size inductor and low-voltage-rating semiconductor devices, operates at a high-efficiency mode because of the zero-current switching operations of all the semiconductor devices. The operational principles are explained and a design example is provided in the study. Experimental results demonstrate the validity of the proposed converter.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.507-510
• /
• 2003

This paper presents a novel prototype of tile three-phase bridge power block module type a auxiliary resonant AC link snubber circuit, which is effectively used for the three-phase voltage source type sinewave soft switching PWM inverter using IGBTs. Its operating principle Is described for current source load model, along with its practical design approach based on the simulation data. The performance evaluation of the three-phase voltage source type snewave soft switching PWM inverter incorporating a single three-phase bridge mo여le of active auxiliary resonant AC link snubber treated here Is illustrated, which is concerned with power duality efficiency power loss analysis. This inverter is discussed as compared with those of tile three-phase voltage source type sinewave hard switching PWM inverter. The power loss analysis of this soft switching PWM Inverter using IGBT power modules is evaluated on the basis of the measured v-i characteristics and switching power losses of IGBT, and antiparaliel diodes. The practical effectiveness of this inverter is proven by the power loss analysis for distributed power supply.

• Journal of Power Electronics
• /
• 제4권2호
• /
• pp.77-86
• /
• 2004

This paper presents a novel three-phase power module bridge type auxiliary resonant AC link snubber for the three-phase voltage-fed sinwave soft switching PWM inverter operating under specific instantaneous space voltage vector modulation. The operating principle of this resonant snubber is described for current source load model during one switching period, along with its design approach based on the simulation data. The performance evaluations of space vector modulation three-phase sinewave soft switching inverter with a new three-phase active auxiliary resonant AC link snubber are discussed as compared with those of three-phase voltage source-fed sinewave hard switching PWM inverter with a standard space voltage vector modulation strategy. The power loss analysis and conventional efficiency estimation of three-phase soft switching PWM inverter using ICBT modules are carried out including all the conduction power losses based upon the measured v-i characteristics of IGBT and its antiparallel diode as well as their switching losses.