• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.433-438
• /
• 1998

Design lateral strength calculated by current seismic design code is prescribed to be much lower than the force level required for a structure to respond elastically during design level earthquake ground motion. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factor known as "response modification factor, R". This factor accounts for the inherent ductility, overstrength, redundancy, and damping of a structural system. This study considers ductility and overstrength of the wall-type structure for investigating R factor. This means that R factor is determined from the product of "ductility-based R factor($R_$\mu$$) and overstrength factor($R_s$). $R_$\mu$$ factor is calibrated to attain the targer ductility ratio (system ductility capacity) and produced in the from of $R_$\mu$$ spectra considering the influence of target ductility, natural period, and hysteretic model. On the other hand, $R_s$ is more difficult to quantify, since it depends on both material and system-dependent uncertain parameters. In this study Rs factor was determined from the result of push-over analysis.-over analysis.

• Korean Journal of Applied Biomechanics
• /
• v.20 no.4
• /
• pp.487-495
• /
• 2010

The purpose of this study was conducted to make a comparative biomechanical analysis of X-factor and X-factor stretch during driver and iron swing. The subjects were composed of 10 professional golfers with more than 10 years career. The result was as follows: First, the analysis of the back swing with driver and iron swing showed no differences statistically between both the timing in horizontal rotating of shoulder and hip, the time required for X-factor stretch also showed no differences statistically. Second, the back swing with a driver swing showed more maximum horizontal rotation of shoulder and hip joint than the back swing with an iron swing, but the twist of shoulder and hip that was X-factor stretch angle showed no difference. Third, the GRF of the max value for the left and right foot during shoulder and hip horizontal rotation of back swing showed no differences statistically in the movement of driver and iron swing during the back swing, and the GRF of X-factor stretch for the left and right foot showed no differences statistically in driver and iron swing. Therefore the result of this research showed that the operation of torso(X-factor stretch) and weight shifting were similar although the horizontal rotation of body was different during the driver and iron swing.

• Culinary science and hospitality research
• /
• v.14 no.2
• /
• pp.1-17
• /
• 2008

This study analyzed the factors related to the stress which the top-rated chefs in Jeju suffer and conducted the multiple regression analysis to look into the effect of job-related stress on the stress reaction and the satisfaction with job, in order to examine the effect of job-related stress faced by hotel kitchen employees in performing duties and determine the effect of job-related stress on the reaction of individuals in the peculiar environment of a kitchen in a hotel. Job-related stresses were classified into five factors which were physical, individual, vocational, organizational, and social. The result of regression analysis, which was performed to figure out the effect of job-related stress on the stress reaction and the satisfaction with the job, indicated that the physical factor of job-related stress had the greatest effect on the physiological reaction, followed by the organizational factor, individual factor, and social factor, while the organizational factor of job-related stress had the greatest effect on the psychological reaction, followed by the individual factor, social factor, vocational factor, and physical factor. Meanwhile, the vocational factor of job-related stress had the greatest effect on behavioral re-action, followed by organizational factor and individual factor. The vocational factor of job-related stress had the greatest effect on the satisfaction with the job, followed by individual factor, organizational factor, social factor, and physical factor.

• The Journal of Korean Academic Society of Nursing Education
• /
• v.8 no.1
• /
• pp.61-71
• /
• 2002

purpose : The purpose of this study was to find out the influencing factors of smoking-cessation behavior of patients with coronary heart disease and to suggest the model of smoking-cessation behavior which was based on the relationship between influencing factors and then to test its fitness empirically. method : This study was based on the Theory of Reasoned Action and a hypothetical model was constructed with fifteen paths in consideration of main predictive factors of smoking-cessation behavior such as biological factor, disease-related characteristics, self-efficacy, supportive factor, environmental factor, disease-related perception factor, intention-to-quit, and psychological factor. The validity of a smoking- cessation model was tested to 264 patients with coronary heart disease by using SPSS 8.0 and Window LISREL 8.12a. results : 1. Seven of the 15 paths of smoking-cessation behavior proved to be significant. 2. The final model excluded three paths in the hypothetical model was demonstrated to be improved by $x^2$=44.31 (df=38, p=.22), Goodness of Fit Index (GFI)=.98, Adjusted Goodness of Fit Index (AGFI)=.96, Non-Normed Fit Index(NNFI)=1.00, Normed Fit Index(NFI)=1.00, and Root Mean Square Residual(RMR)=.24. 3.The smoking-cessation behavior was influenced directly by biological factor, self-efficacy, supportive factor, environmental factor, intention-to-quit, and psychological factor. The smoking-cessation behavior was accounted for 82% of variance by these factors. conclusion : although the adolescents' smoking behavior can be predicted by only smoking intention, it is hard to predict the adults' smoking-cessation behavior by only this factor. Therefore, intention-to-quit, self-efficacy, supportive factor should be improved because these are promotive factors for smoking-cessation behavior. Biological factor, environmental factor, and psychological factor are inhibitive factors, so nicotine replacement therapy is helpful to the high nicotine-dependents, and ex-smokers avoid other smokers in their environment and also patients should learn and practice the stress coping-skills.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.27 no.1
• /
• pp.93-102
• /
• 2004

In recent several studies, interactional justice as well as distributional justice and procedural justice was founded as a important factor of justice. But the other studies proposed that interactional justice was a sub-dimension of procedural justice because of a very close correlation between two factors. So there are mixed point of view of the factor structure of justice. In this study, we examined the factor structure of justice using confirmative factor analysis. We hypothesized that the facto, structure of justice would be divided into three factors; distributional justice, procedural justice and interactional justice. The results of empirical study supported these hypotheses. The results of this study suggest that interactional justice should be regarded as a important factor of justice to analyze the justice and the relationship with justice and related variables more accurately.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.9
• /
• pp.932-936
• /
• 2002

This paper has been studied a calibration techniques in CISPR A for 1 m monopole antenna factor in the frequency range below 30 MHz. The equivalent capacitance substitution method uses a dummy antenna in place of the actual rod element. Dummy antenna measure frequency from 150 kHz to 30 MHz and good results factor from 150 kHz to 25 MHz compare to using 1 m monopole antenna factor. It will be use to substitute dummy antenna factor for 1 m monopole antenna factor.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.67 no.3
• /
• pp.155-159
• /
• 2018

Recently, the expansion or establishment of facilities for the logistics system is increasing. Conveyor facilities play a major role in sorting and transporting logistics. Induction motors are widely used for the operation of these conveyor systems. In the logistics system, a large number of induction motors are used. These motors have a considerable distance from the power source side and have a low power factor. The installation position for the power factor compensation of the induction motor is very important. Since the voltage drop depends on the length of the line, it is an important parameter in capacitor capacity determination for power factor compensation. The capacity of the capacitors installed to compensate the power factor of the inductive load should be designed to the extent that self-excitation does not occur. In this study, we analyze the method of compensating the proper power factor considering the voltage drop and the installation position of the induction motor in the logistics system.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.15 no.4
• /
• pp.71-84
• /
• 2019

Various researchers conducted the research on two-factor authentication suitable for wireless sensor networks (WSNs) after Das first proposed two-factor authentication combining the smart card and password. After then, To improve the security of user authentication, elliptic curve cryptography(ECC)-based authentication protocols have been proposed. Jiang et al. proposed a privacy-aware two-factor authentication protocol based on ECC for WSM for resolving various problems of ECC-based authentication protocols. However, Jiang et al.'s protocol has the vulnerabilities on a lack of mutual authentication, a risk of SID modification and a lack of sensor anonymity, and user's ID exposed on sensor node Therefore, this paper proposed security enhanced privacy-aware two-factor authentication protocol for wireless sensor networks to solve the problem of Jiang et al.'s protocol, and security analysis was conducted for the proposed protocol.

• Journal of Korean Academy of Nursing
• /
• v.43 no.5
• /
• pp.587-594
• /
• 2013

Purpose: The purpose of this study is to provide researchers with a simplified approach to undertaking exploratory factor analysis for the assessment of construct validity. Methods: All articles published in 2010, 2011, and 2012 in Journal of Korean Academy of Nursing were reviewed and other relevant books and articles were chosen for the review. Results: In this paper, the following were discussed: preliminary analysis process of exploratory factor analysis to examine the sample size, distribution of measured variables, correlation coefficient, and results of KMO measure and Bartlett's test of sphericity. In addition, other areas to be considered in using factor analysis are discussed, including determination of the number of factors, the choice of rotation method or extraction method of the factor structure, and the interpretation of the factor loadings and explained variance. Conclusion: Content validity is the degree to which elements of an assessment instrument are relevant to and representative of the targeted construct for a particular assessment purpose. This measurement is difficult and challenging and takes a lot of time. Factor analysis is considered one of the strongest approaches to establishing construct validity and is the most commonly used method for establishing construct validity measured by an instrument.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2007.04a
• /
• pp.37-47
• /
• 2007

Factor : Structure Metal pad & SMO size Board level TC test : - Large SMO size better Board level Drop test : - Large SMO size better Factor : Structure Substrate thickness Board level TC test : - Thick substrate better Board level Drop test : - Substrate thickness is not a significant factor for drop test Factor : Material Solder alloy Board level TC test : - Not so big differences over Pb-free solder and NiAu, OSP finish Board level Drop test : - Ni/Au+SAC105, CuOSP+LF35 are better Factor : Material Pad finish Board level TC test : - NiAu/NiAu is best Board livel Drop test : - CuOSP is best Factor : Material Underfill Board level TC test - Several underfills (reworkable) are passed TCG x500 cycles Board level Drop test : - Underfill lots have better performance than non-underfill lots Factor : Process Multiple reflow Board level TC test : - Multiple reflow is not a significant actor for TC test Board level Drop test : N/A Factor : Process Peak temp Board level TC test : - Higher peak temperature is worse than STD Board level Drop test : N/A Factor : Process Stack method Board level TC test : - No big difference between pre-stack and SMT stack Board level Drop test : - Flux dipping is better than paste dipping but failure rate is more faster