• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.1
• /
• pp.10-14
• /
• 2014

Niobium nitride coatings have many potential thin film applications due to their chemical inertness, good mechanical properties, temperature stability and superconducting properties. In this study, $NbN_x$ coatings were prepared by inductively coupled plasma (ICP) assisted DC magnetron sputtering method on the surface of AISI 304 austenitic stainless steels. Effects of target power were studied on mechanical and chemical properties of the coatings. The coating structure was analyzed by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The coating hardness was measured by micro-knoop hardness tester. The coating thickness was measured using a 3D profiler and wear characteristics were estimated using a ball-on-disk wear tester. The thickness of the $NbN_x$ coatings increased linearly from 300 nm to 2000 nm as the Nb target power increased, and it showed over $HK_{0.005}$ 4000 hardness above Nb target power of 300 W. Hexagonal ${\delta}^{\prime}$-NbN phase and cubic ${\delta}$-NbN phase were observed in the coating films and the hardness of the NbNx coatings was higher when these two peaks were mixed. The corrosion resistance increased with the increase of the Nb target power.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.3
• /
• pp.416-420
• /
• 2002

Various products of karanj (Pongamia glabra) are utilized for industrial, health and animal agriculture applications in the Indian subcontinent. Despite a rich source of protein (CP, 28-34%), karanj cake was found to be slightly bitter in taste and toxic owing to the presence of flavonoid (Karanjin), restricting its safe inclusion in the livestock diets. Feeding trials with raw cake revealed its poor palatability and adverse performance among different categories of livestock including poultry. The present study was, therefore, aimed to detoxify karanj cake by various physico-chemical methods like solvent extraction, water washing, pressure cooking and alkali and acid treatments. The level of residual karanjin in raw and variously processed cake was quantified using high performance liquid chromatography (HPLC). The raw expeller karanj cake was found to contain about 0.19% of karanjin. Though a non-polar solvent, soxhlet extraction of expeller pressed cake with petroleum ether drastically reduced karanjin content (0.01%). Soaking of cake for 24 h in 1% NaOH (w/w) solution was found to reduce karanjin to a major extent with little further benefit by increasing alkali level. Milder alkalies like lime and fertilizer grade urea reduced the karanjin levels marginally. Similar was the case with mineral acids such as HCl and glacial acetic acid. It was, therefore, concluded that solvent extraction of karanj seeds would be the best method of detoxification as well as for more recovery of oil and karanjin.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.72-80
• /
• 2018

With the ever increasing advances in computers and their computing power, computational fluid dynamics(CFD) has become an essential engineering tool in the design and analysis of engineering applications. Accordingly, many universities have developed and implemented a course on CFD for undergraduate students. On the other hand, many professors have used industrial examples supplied by computational analysis software companies as CFD examples. This makes many students think of CFD as difficult and confusing. This paper presents a simple CFD example used in the department of mechanical design engineering of Kangwon National University and shows its effectiveness. Most students answered that a simple CFD example is more comprehensive than an industrial example. Therefore, it is necessary to develop simple computational analysis problems in the engineering education field.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.4
• /
• pp.602-611
• /
• 2013

We have investigated the influence of system composition and preparation conditions on the particle size of vitamin E acetate (VE)-loaded nanoemulsions prepared by PIC(phase inversion composition) emulsification. This method relies on the formation of very fine oil droplets when water is added to oil/surfactant mixture. The oil-to-emulsion ratio content was kept constant (5 wt.%) while the surfactant-to-oil ratio (%SOR) was varied from 50 to 200 %. Oil phase composition (vitamin E to medium chain ester ratio, %VOR) had an effect on particle size, with the smallest droplets being formed below 60 % of VOR. Food-grade non-ionic surfactants (Tween 80 and Span 80) were used as an emulsifier. The effect of f on the droplet size distribution has been studied. In our system, the droplet volume fraction, given by the oil volume fraction plus the surfactant volume fraction, was varied from 0.1 to 0.3. The droplet diameter remains less than 350 nm when O/S is fixed at 1:1. The droplet size increases gradually as the increasing the volume fraction. Particle size could also be reduced by increasing the temperature when water was added to oil/surfactant mixture. By optimizing system composition and homogenization conditions we were able to form VE-loaded nanoemulsions with small mean droplet diameters (d < 50 nm). The PIC emulsification method therefore has great potential for forming nanoemulsion-based delivery systems for food, personal care, and pharmaceutical applications.

• Journal of the Korean Society of Safety
• /
• v.35 no.4
• /
• pp.23-31
• /
• 2020

In the construction sector, there were 99 fatalities from falls associated with steel tube and system scaffolds for three years from 2016 to 2018 and out of which 27.3 percent (27 workers) were found to have occurred during installing and dismantling procedure. To erect scaffolding which is installed for the work at height, the work platforms are generally installed first and the safety guardrails are installed and vice versa to dismantle. As a result, workers are exposed to the risk of falling because they erect and dismantle scaffolding without guardrails. To minimize the risk of falling, it is necessary to study a new construction method that can erect or dismantle scaffolding while guardrails are installed (called advanced guardrail system). This study analyzed advanced guardrail system in terms of safety regulation, workability and economic efficiency by investigating the domestic situation on the use of scaffolding, reviewing domestic and foreign standards for guardrails and conducting economic feasibility study. The results of this study is expected to greatly contribute to preventing falls in scaffolding installation and dismantlement procedure. As a follow-up study, empirical research is required including physical test of scaffolding with advanced guardrail system and effectiveness analysis after trial applications.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.2
• /
• pp.239-244
• /
• 1998

Piezoelectric pressure sensors and pyroelectric infrared detectors based on ZnO thin film have been integrated with GaAs metal-semiconductor field effect transistor (MESFET) amplifiers. Surface micromachining techniques have been applied in a GaAs MESFET process to form both microsensors and electronic circuits. The on-chip integration of microsensors such as pressure sensors and infrared detectors with GaAs integrated circuits is attractive because of the higher operating temperature up to 200 oC for GaAs devices compared to 125 oC for silicon devices and radiation hardness for infrared imaging applications. The microsensors incorporate a 1${\mu}$m-thick sputtered ZnO capacitor supported by a 2${\mu}$m-thick aluminum membrane formed on a semi-insulating GaAs substrate. The piezoelectric pressure sensor of an area 80${\times}$80 ${\mu}$m2 designed for use as a miniature microphone exhibits 2.99${\mu}$V/${\mu}$ bar sensitivity at 400Hz. The voltage responsivity and the detectivity of a single infrared detector of an area 80${\times}$80 $\mu\textrm{m}$2 is 700 V/W and 6${\times}$108cm$.$ Hz/W at 10Hz respectively, and the time constant of the sensor with the amplifying circuit is 53 ms. Circuits using 4${\mu}$m-gate GaAs MESFETs are fabricated in planar, direct ion-implanted process. The measured transconductance of a 4${\mu}$m-gate GaAs MESFET is 25.6 mS/mm and 12.4 mS/mm at 27 oC and 200oC, respectively. A differential amplifier whose voltage gain in 33.7 dB using 4${\mu}$m gate GaAs MESFETs is fabricated for high selectivity to the physical variable being sensed.

• Resources Recycling
• /
• v.14 no.3
• /
• pp.55-62
• /
• 2005

Mechanical properties of shell powder containing mixed recycled plastics were investigated depending on the shell content and surface modification. First, shell powder and LDPE were compounded using the twin screw extruder to manufacture 40 wt% master batch(M/B), and the M/B was blended with LDPE to produce bulk specimens with 10, 20, 30 and 40 wt% shell content. To improve the compatibility of shell powder with mixed recycled plastics matrix, surface of shell powder was chemically modified with cations or cationic surfactant. Surface modified shell was also used to prepare bulk specimens with the same shell content. Mechanical property analysis showed obvious improvement for the surface modified shell containing bulk specimens compared to unmodified ones. These results can lead to the development of new applications for the mixed recycled plastics.

• Journal of Veterinary Clinics
• /
• v.28 no.1
• /
• pp.57-62
• /
• 2011

The shortage of transplantable kidneys has many efforts to regenerate bioartificial kidneys using transgenic animals and diverse kinds of scaffolds which are important tools for cell seeding. However, there are many limitations for clinical applications so far. Recently, decellularized bioscaffolds using animal organs come into spotlight because of its many superior advantages. In current study, we produced decellularized kidney bioscaffolds of pig which is an attractive animal as a clinical model for human. We decellularized pig kidneys with 1% SDS detergent solution using peristaltic pump systems for 12h. After decellularization process, the kidney bioscaffolds preserved intact 3D morphology including glomerular structure and almost DNA from pig was entirely removed. In addition, this process could preserve micro vascular network which is necessary for cell survival. Although, additional studies for recellularization and transplantation should be required, the decellular vascularized kidney bioscaffolds might have many potentials for kidney regeneration.

• 한국HCI학회:학술대회논문집
• /
• 2008.02b
• /
• pp.552-557
• /
• 2008

'Digilog Book' dealing with the combination of each advantage of analog sensibility on texts and digital sensation on virtual reality is one of the noble applications of U-book. Based on contents from books, enhancing 3D immersive display enable readers to enjoy various experiences with multisensory feedback provided. Also, 'Digilog Book' provides digitally created stories that would project different experiences and environments interacting users' choices on the interface of the book. This study focuses on developing users friendly implementation tools providing more interaction between digitally generated stories and digitally generated interface so that interaction between virtual reality and actual realty is expanded through simulating contexts and extents. From the application scenario 'Digilog Book' would perform as a storytelling tool with developing subordinated elements such as context structure, screen structure, definition of writing function, writing interface, writing system structure, etc. Therefore, this study would become a significance to direct and indicate the development of writing techniques on virtual reality back to life through digitally augmented reality.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.1-13
• /
• 2008

An efficient segregated algorithm for the coupling of velocity and pressure of incompressible fluid flow, called IDEAL Inner Doubly-Iterative Efficient Algorithm for Linked-Equations), has been proposed by the present authors. In the algorithm there exist double inner iterative processes for pressure equation at each iteration level, which almost completely overcome two approximations in SIMPLE algorithm. Thus the coupling between velocity and pressure is fully guaranteed, greatly enhancing the convergence rate and stability of solution process. The performance of the IDEAL algorithm for three-dimensional incompressible fluid flow and heat transfer problems is analyzed and a systemic comparison is made between the algorithm and three other most widely-used algorithms (SIMPLER, SIMPLEC and PISO). It is found that the IDEAL algorithm is the most robust and the most efficient one among the four algorithms compared. This new algorithm is used for the velocity prediction of a new interface capturing method. VOSET, also proposed by the present author. It is found that the combination of VOSET and IDEAL can appreciably enhance both the interface capture accuracy and convergence rate of computations.