• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2003.06a
• /
• pp.268-271
• /
• 2003

There are several methods for the design of 2D filter. Notable among them is McClellan transform method. This transform allows us to obtain a high order 2D FIR filter through mapping the 1D frequency points of a 1D prototype FIR filter onto 2D frequency contours. We design 2D filter using this transform. Then we notice for mapping deviation of the 2D filter. In this paper, Quadratic programming (QP) method allows us to obtain coefficients of McClellan transform. Then we compare deviation of QP method with least-squares(LS) method. Elliptic filter is used for comparison. The optimal cutoff frequencies of a 1D filter are obtained directly from the QP method. Also several problem of LS method are solved.

• Korean Journal of Optics and Photonics
• /
• v.23 no.1
• /
• pp.6-11
• /
• 2012

A bidirectional TDM-PON link to support 2.5 Gb/s upstream signals of 256 ONUs was considered for an extended transmission distance of 50 km. The power budget of the link was 58 dB for the upstream signal and a SOA was applied as a link extender which had a 25 dB gain. Receiver sensitivity of the upstream signal was -25 dBm for -30 dBm input power to the SOA. When the input power was -10 dBm, pulse overshooting caused by gain transient of the SOA was maximum at 45% and the signal performance degradation gave a power penalty of 1.55 dB for $10^{-12}$ BER. However the penalties diminished rapidly and became negligible as the input power went below -15 dBm. So this input power dynamic range of up to -15 dBm means that it is not positively necessary to use gain control methods for the next generation TDM-PON systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1297-1307
• /
• 2009

The purpose of this paper is to propose a detection algorithm and a tracking algorithm based on silent time using MB-OFDM UWB(Multi-Band Orthogonal Frequency Division Multiplexing Ultra Wide Band) receiver in order to satisfy DAA(Detect And Avoid) regulation of Korea to permit UWB in 3.1~4.8 GHz. In DAA regulation of Korea, if UWB device receives a signal more than -80 dBm/MHz from the victim system during UWB operation, the UWB system should avoid the collision within 2 sec. In this paper, we proposed the detection algorithm to detect the victim signal received by －80 dBm/MHz for the avoidance process that changes the operating UWB frequency to other UWB frequency and the subcarrier tracking algorithm to follow up the subcarrier positions of the victim signal for the tonenulling avoidance process that decreases the TX power of subcarriers occupied by the victim signal by -70 dBm/MHz. The performance of the detection algorithm and the tracking algorithm suggested in this paper is verified in simulation results considering various conditions.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.631-635
• /
• 2004

The rapid development of digital media and communication network urgently brings about the need of data certification technology to protect IPR (Intellectual property right). This paper proposed a new watermarking method for embedding contents owner's audio signal in order to protect color image IPR. Since this method evolves the existing static model and embeds audio signal of big data, it has the advantage of restoring signal transformed due to attacks. Three basic stages of watermarking include: 1) Encode analogue ID owner's audio signal using PCM and create new 3D audio watermark; 2) Interleave 3D audio watermark by linear bit expansion and 3) Transform Y signal of color image into wavelet and embed interleaved audio watermark in the low frequency band on the transform domain. The results demonstrated that the audio signal embedding in color image proposed in this paper enhanced robustness against lossy JPEG compression, standard image compression and image cropping and rotation which remove a part of image.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2000.12a
• /
• pp.85-88
• /
• 2000

Signal splitting and perfect reconstruction in subband coding is based on the assumption that quantization errors are negligible. But if subband signal is quantized, 4 types of errors occurs thus it is not impossible to do perfect reconstruction. These errors are QMF design error, aliasing error, signal error and random error. By using the QMF for subband splitting, the QMF error does not present. and by using the Lloyd-Max quantizer for the quantization and by using an appropriate synthesis filter, all signal dependent errors can be cancelled and the remaining error is random error which is uncorrelated with the original image〔1〕. In this thesis, Lenna and Camera-Man image are devided into 10 subbands by using the D4 and D20 wavelet And the subband signals are quantized by using the Lloyd-Max quantizer and the quantization errors are compared. and evaluated.

• Journal of Navigation and Port Research
• /
• v.46 no.4
• /
• pp.367-374
• /
• 2022

The purpose of this study was to propose a deep learning algorithm that applies to the fault diagnosis of fuel pumps and purifiers of autonomous ships. A deep learning algorithm reflecting the time dependence of the measured signal was configured, and the failure pattern was trained using the vibration signal, measured in the equipment's regular operation and failure state. Considering the sequential time-dependence of deterioration implied in the vibration signal, this study adopts Conv1D with sliding window computation for fault detection. The time dependence was also reflected, by transferring the measured signal from two-dimensional to three-dimensional. Additionally, the optimal values of the hyper-parameters of the Conv1D model were determined, using the grid search technique. Finally, the results show that the proposed data preprocessing method as well as the Conv1D model, can reflect the sequential dependency between the fault and its effect on the measured signal, and appropriately perform anomaly as well as failure detection, of the equipment chosen for application.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.47-52
• /
• 2017

In this paper, CMOS SAR A/D converter 1.8V supply for the design of an A/D converter having an middle speed for the biological signal processing was designed. This paper proposes design of a 10-bit SAR Analog to Digital Converter improving linearity driven by MSB node of C-DAC array divided into 4 equal parts. It enhances linearity property, by retaining the analog input signal charging time at MSB node. Because MSB node samples analog input, it enhances resolution through getting initial input signal precisely. By using split capacitor on C-DAC array, it reduced chip size and power dissipation. The Proposed SAR A/D Converter is fabricated in 0.18um CMOS and measured 7.5 bits of ENOB at sampling frequency 4MS/s and power supply of 1.8V. It occupies a core area of $850{\times}650um^2$ and consumes 123.105uW. Therefore it results in 170.016fJ/step of FOM(Figure of Merit).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.3
• /
• pp.68-73
• /
• 2011

In this paper, a compact-narrow open stub band-pass filter with parasitic-signal of low frequency range and second harmonics rejected using the parallel coupled line and FLCLM(Frquency Locked Controlled Length Method) is proposed. The characteristic of the parallel coupled line can be rejection for parasitic-signal of low frequency range and second harmonics. In last filter of experimental results show that insertion loss is 1.2 dB and return loss is 14.8 dB, and the fractional bandwidth is 10 % at the center frequency of 5.8 GHz. In additional, the rejection for parasitic-signal of low frequency range and second harmonics are 28.9 dB and 28.8 dB, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.90-98
• /
• 1999

This paper presents a wideband single-balanced mixer using a diode which can be used in RF receiver of microwave measurement systems. For wideband characteristic, local oscillator(LO) signal is provided to diode with low loss using a coplanar waveguide-to-slotline balun. For high isolation characteristic radio frequency (RF) port and intermediate frequency (IF) port are designed using directional coupler. This mixer presents 30.5~31.17dB conversion loss whose flatness is within 1dB for 9 kHz~2.6 GHz wideband RF signal, and above 30 dB isolation for LO signal.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.9 s.339
• /
• pp.1-10
• /
• 2005

In this paper, we proposed predistortion algerian that can compensate temperature distortion by digital. Predistortion algorithm produces compensation value of distortion by temperature as well as system nonlinear distortion by input level, and warps beforehand signal of baseband. To prove excellency of such algorithm we applied predistortion algorithm to Saleh's high power amplifier model, and did computer simulation. As a result, P1dB increased about 0.5 dBm phase shift reduced about $0.8^{o}$ than existent the A&P PD, and predistiortion algorithm to apply temperature compensation techniques improved P1dB about 2dBm and stabilized phase shift by about $0.1^{o}$ low. When approved UMTS's sample signal to this amplifier, IMD3 of amplifier decreased 10dBm than is no temperature compensation techniques, and reduced 19dBm than signal that is no distortion.