• Geotechnical Engineering
• /
• v.10 no.3
• /
• pp.41-54
• /
• 1994

This study aims at investigating the mechanism and operation of cubical triaxial test developed by Lade in order to obtain analysis on the clayey foundation deformation. A comparison on deviator stress, pore water pressure and stress path is made between test results of clay using the cubical consolidated undrained test as well as plane strain test.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.169-178
• /
• 1991

A plane-strain finite element analysis of sheet metal forming is carried out by using the rigid-plastic FEM based on the membrane theory. The sheet material is assumed to possess normal anisotropy and to obey Hill's new yield criterion and its associated flow rule. A formulation of initial guess generation for the displacement field is derived by using the nonlinear elastic FEM. A method of contact treatment is proposed in which the skew boundary condition for arbitrarily shaped tools is successively used during iteration. In order to verify the validity of the developed method, plane-strain drawing with tools in analytic expression and with arbitrarily shaped tools is analyzed and compared with the published results. The comparison shows that the present method can be effectively used in the analysis of plane-strain sheet metal forming and thus provides the basis of approximate sectional analysis of panel-like sheet forming.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.2
• /
• pp.70-79
• /
• 1999

The lower ground of structure, in which the strip loads, such as earth dams and embankments , are signiificantly working on , is required to be interpreted as a state of plane strain where the strain of intermediated principal stress direction is put '0' . The plane strain state is frquently observed in actural soil engineering case. For those case, drained stress-strain and strength behavior of Iksan weathered granite soil prepared in cubical specimens with cross-anisotropic fabric was studied by conventional triaxial compression, plane strain and cubial triaxial tests with independent control of the three principal stress. All specimens were loaded under conditions of principl stress directions fixed and aligned with the directions of the material axes. As a result of research , when a ground condition is analyzed under plane strain state, the shear strength obtained from the conventional triaxial compression test can be understimated.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.1
• /
• pp.11-21
• /
• 2015

This study aims at investigating of the behavioral characteristics of foundation ground subjected to a strip load in anisotropy. Using marine clays sampled at Shihwa area, a series of laboratory tests including triaxial compressive test, plane strain compressive and expansion tests that allows horizontal deformation only and zero strain (${\varepsilon}_2$) in the direction of intermediate stress (${\sigma}_2$) are conducted. In addition, a numerical analysis using parameters obtained from the tests is carried out. In the numerical analysis, Cam-clay model that simulates the behavior of natural deposited clay properly is adopted. The analysis results show that the vertical displacements of the plane strain compressive tests are relatively larger than those of triaxial compressive tests by 18-25%. Likewise, the horizontal displacements is 13-19% larger.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2001.06a
• /
• pp.425-428
• /
• 2001

본 논문에서 구현한 메쉬 편집기는 편집할 메쉬의 몇몇 점을 편집할 경우, 편집 정보가 그 점에 이웃한 점들에게도 영향을 미치게 되어, 편집 결과가 근사된 부드러운 곡면으로 표현하도록 하는 데 있다. 그러기 위해서는 3차원의 메쉬를 2차원 평면으로 매핑할 때, 매핑되는 원래의 메쉬의 모양이 크게 변형되지 않도록 하여야 하는데, 여기에 모양 유지 매개 변수화 방법을 사용하고 있다. 편집에 사용된 점의 편집 정보는 2차원 평면 다각형 안에 있는 서로 대응되는 점으로 매핑 되고, B-스플라인 보간으로 편집 정보는 2차 평면 안에 있는 다른 점들에게도 영향을 주게 된다. 이런 결과는 3차원 메쉬로 환원되어 부드럽게 근사된 곡면으로 표현된다.

• Geotechnical Engineering
• /
• v.14 no.4
• /
• pp.33-46
• /
• 1998

Anisotropy of stiffness, from extremely small strains to post-failure strains, of isotropically consolidated air-pluviated sands in plane strain compression was studied by using the newly developed instrumentation for small strain measurements. Seven types of sand of the world-wide origins were tested, which have been extensively used for research purposes. Stress-strain at the specimen boundaries. It was found that the maximum Young's modulus $E_{max}$ was irrespective of the angle $\delta$ of the $\delta_1$ direction relative to the bedding plane. However, the normalized$ E_{max}$ was varied with the types of sand. Furthermore, the dependency of the strain and stress level on the stiffness was increased as $\delta$ decreased.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.12
• /
• pp.17-25
• /
• 2012

FEM requires the stress-strain relationship equations for numerical analyses. However, most formulations for the stress-strain relationship published up to the present are not satisfactory enough to properly express all the levels from the small strain to the peak. Tatsuoka and Shibuya (1991) suggested a new single formulation applicable not only to a wide range of geo-materials from soft clay to soft rock, but also to a wide range of strain levels from $10^{-6}$ to $10^{-2}$. The plain strain compression test is carried out to seven samples of research standard sand specimens and two samples of glass beads, which have been used at world-renowned research institutes. In this study, strains of the maximum principal stress (${\sigma}_1$) and the minimum principal stress (${\sigma}_3$) were thoroughly measured from $10^{-6}$ to $10^{-2}$, and the result, applied to Tatsuoka and Shibuya's new formulation, coincided closely with the measured data of the stress-strain relationship from the small strain to the peak.

• Composites Research
• /
• v.17 no.1
• /
• pp.38-46
• /
• 2004

This paper aims to correlate the micro-mechanical behaviour of tow geometry with applied in-plane forces during deformation of dry woven carbon-fibre fabric. These in-plane forces lead to differences in tow reorganisation during deformation and so changes in the way in which 'lock-up' occurs. In this paper, deformation of micro-mechanical parameters such as tow interval, crimp angle, change in tow amplitude and wavelength are investigated. To observe the micro-deformation of the fabric structure, appropriate specimens from bias extension and biaxial tests are sectioned and observed under the microscope. It was found that different loading conditions cause geometric deferences in the tow architecture. The variation in deformed tow geometry with shear angle is fitted using a simple parametric model.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.33-40
• /
• 1994

Welding of structure produces welding residual stresses which influence buckling strength, brittle fracture strength and cold crack on the weld parts. Therefore, it is very important to accurately analyze the residual stress before welding in order to guarantee the safety of weldment. If the weld length is long enough compared to the thickness and the breadth of plate, thermal and mechanical behaviors in the middle portion of the plate are assumed to be uniform along the thickness direction(z-axis). Thus, the following conditions(so-called plane deformation) can be assumed for the plate except near its end;1) distributions of stress and strain are independent on the z-axis;2) plane normal to z-axis before deformation remains plane during and after deformation. In this paper, plane-deformation thermal elasto-plastic problem is formulated by being based on the finite element method. Moreover special regards and paid to the fact that material properties in elastic and plastic region are temperature-dependence. And the method to solve the plane-deformation thermal elasto-plastic problem is shown by using the incremental technique. From the results of analysis, the characterisics of distribution of welding residual stress and plastic strain with the production mechanism are clarified.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.2
• /
• pp.117-126
• /
• 2009

In order to test the accuracy between the modified mild slope equation (MMSE) without evanescent modes and the plane-wave approximation (PA) of eigenfunction expansion method, various numerical results from both models are presented. In this study, analytical solutions of two models are employed, one based on the MMSE derived by Porter (2003) and the other on the scatterer method of PA by Seo (2008a). Judging from direct comparisons against existing results of rapidly varying topography, the PA model gives better predictions of the wave propagation than the MMSE model.