• Korean Journal of Optics and Photonics
• /
• v.21 no.4
• /
• pp.168-174
• /
• 2010

Fiber optic current sensors based on polarization-rotated reflection interferometry are demonstrated by incorporating them into polymeric optical waveguide components, including polarization-maintaining 3-dB couplers, TE-pass waveguide polarizers, and thermooptic phase modulators. To remove the bending induced birefringence, optical fiber coil is annealed at $850^{\circ}C$ for 24 hours. The reflection interferometry comprising polymer waveguide devices exhibit a highly stable output signal corresponding to the flowing current.

• Korean Journal of Optics and Photonics
• /
• v.15 no.4
• /
• pp.293-298
• /
• 2004

We investigate the effect of the wing width and thickness of a Double-Sided Deep-Ridge(DSDR) vertical directional coupler on the coupling length dependent on the polarization, We have found that the DSDR vertical directional coupler without a wing does not have polarization independent coupling lengths. The variation of the coupling length of TE and TM modes and the difference between the coupling lengths of the two modes are negligible as the wing width increases beyond the specific wing width for the same wing thickness. Thus, we can see that a DSDR vertical directional coupler has a wing width larger than the minimum wing width to obtain the polarization independent coupling length. The minimum wing width increases as the wing thickness increases for the same core thickness and as the core thickness decreases for the same wing width. Also, we have found that the minimum wing thickness is determined by the core thickness and the minimum wing thickness decreases as the core thickness increases.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.177-177
• /
• 2011

Complementary metal-insulator-metal capacitor에서 $SiO_2$는 절연체로 널리 사용되고 있었으나, 반도체 소자의 고직접화로 인한 선폭의 감소로 터널링 효과에 의해 누설전류가 증가하여, 대체 물질에 대한 연구가 활발히 진행되고 있다. 그 중 $ZrO_2$는 고유전율, wide bandgap, 열안정성의 특징을 가지고 있어 대체 물질로 주목 받고 있다. $ZrO_2$ 박막 제작에는 sputter, atomic layer deposition 등의 진공증착을 이용한 방법과 용액을 이용한 sol-gel 법이 있다. 화학용액을 이용한 sol-gel 법은 소자의 패턴을 프린트 할 수 있는 장점과 상대적으로 값싼 공정으로 인해 최근 주목 받고 있지만, 진공증착법에 비해서 연구가 전무한 실정이다. 본 연구에서는 sol-gel 법에 의해 프린트된 $ZrO_2$ 박막의 광특성을 분광타원편광분석법으로 연구하였다. Si 기판위에 0.1 M의 $ZrO_2$ sol을 입힌 뒤에 $300{\sim}700^{\circ}C$의 온도에서 열처리 하였다. 분광타원 편광분석기로 1.12~6.52 eV 에너지 영역에서 측정하였고, $ZrO_2$ 박막의 광특성 분석을 위해서 Tauc-Lorentz 모델을 이용하였다. 그 결과 고온에서의 열처리로 인해 효율이 높아서 소자로 이용할 수 있는 tetragonal 구조를 가진 $ZrO_2$ 박막이 형성됨을 분석할 수 있었다. 본 연구는 sol-gel법으로 제작된 $ZrO_2$ 박막의 고직접, 고속 소자응용성과 비파괴적인 광특성 분석법을 제시하고 있다.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.458-466
• /
• 2011

In the mixed system of supercritical carbon dioxide/organic solvents, poly(vinyl alcohol)(PVA) film of high degree of hydrolysis could be dyed with a dichroic dye of C. I. direct black 22(DB22) and as a result, high durability was obtained. Especially, as a dye dispersant in a supercritical fluid phase, a mixed solvent system of ethylene glycol: dimethyl sulfoxide=4 : 6 weight ratio was investigated. Then the optimum pressure for dyeing could be reduced down to 200 bar. Using this supercritical fluid system, the maximum dyeing appeared as the transmittance of less than 1% and the waste amount was reduced to the level of 1/10. After 500% drawing of this PVA film, both the polarizing efficiency of 94% and the single piece transmittance of 30% were obtained. The limitation of DB22 and further improvements were also discussed.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.467-472
• /
• 2002

In this paper, we propose a polarization-insensitive temperature sensor using a thermo-optic effect of the upper and (or) lower cladding of a planar waveguide in contact with a side-polished fiber. A microscope cover glass with thickness of a 170 ${\mu}{\textrm}{m}$ is adopted as an overlay waveguide because this waveguide opposes sudden temperature change and ensures polarization-insensitive responses. The measured polarization-dependence loss is less than 0.3 dB. The temperature can be detected as a result of the shift in coupling wavelength of the sensor. We investigate the shift in coupling wavelength as a function of the temperature variation with respect to the different thermo-optic coefficients of lower and upper claddings. We also show that the temperature sensitivity of the device can be easily controlled by the thermo-optic coefficients of lower and upper claddings of the overlay waveguide.

• Korean Journal of Optics and Photonics
• /
• v.26 no.6
• /
• pp.306-311
• /
• 2015

We report the characteristics of a single-wavelength-tunable fiber laser using a polymer waveguide Bragg grating (PWBG) wavelength filter. The output of the laser depends on environmental conditions, such as temperature and polarization states in the laser cavity. Wavelength tuning can be achieved, about 16.29 nm from 1548.24 nm to 1531.95 nm, according to the electric power applied to the PWBG wavelength filter. The achieved efficiency slope is about -0.16 nm/mW. A side-mode suppression ratio (SMSR) of more than 35 dB can be obtained by adjusting the polarization state in the laser cavity. A stable wavelength-tunable fiber laser can be achieved using the PWBG wavelength filter with a TEC module and a polarization-maintaining fiber.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.3
• /
• pp.179-187
• /
• 2008

In this paper, we carried out the performance evaluation of depolarized fiber optic gyroscope(D-FOG) that was designed and fabricated with the low-cost optical communication single mode fiber and depolarizer. In order to reduce the phase error of D-FOG, the circuit of stabilized current and temperature of the light source was made and the performance was analyzed. The current and the temperature stability of the fabricated stabilization circuit were less than $200{\mu}A$ and $0.0098^{\circ}C$, respectively. Also, the D-FOG's experimental result showed that the value of the dynamic range of rotated rate, the scale factor error with a good linearity, and the zero bias drift were ${\pm}50^{\circ}/s$, 2.8881%, and $19.49^{\circ}/h$, respectively. The results indicated that a low-cost FOG was able to fabricate which was more cost effective than conventional FOG with a high-cost high-birefringent polarization maintaining fiber.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.11
• /
• pp.71-78
• /
• 2019

Most 3D displays that are currently in the market adopt the binocular disparity method creating a different image for the left and right eye for a 3 dimensional effect. However, commercialized 3D image output devices lack in performance making it uncomfortable for the viewer and restrict the viewer to certain positions. In this paper, we propose a single-cell polarized lens type stereoscopic system which has a smaller viewing angle and reduced crosstalk, with improved light penetration compared to existing double-cell structures; and analyzed the single-cell polarized lens type stereoscopic system properties, and conducted an effect analysis of performance improvement compared to the dual-cell type. Results showed that the single-cell type had a 25% improved performance, and the 3D crosstalk index which is an important index for quality characteristics of stereoscopic systems, increased over about 37%, compared to the dual-cell type.

• Applied Chemistry for Engineering
• /
• v.22 no.1
• /
• pp.81-86
• /
• 2011

The aqueous solution of Sunset Yellow-FCF (SY-FCF) began to show schlieren texture at room temperature when its concentration reaches 25 wt%. A further increase of the concentration of SY-FCF to 28 wt% resulted in a perfect nematic liquid crystal phase. However, more than 30 wt% of SY-FCF in aqueous solution was required to make an optically anisotropic film simply by shear coating. In our study, concentration of SY-FCF solution, coating speed, drying temperature, and relative humidity were considered as coating parameters affecting the preparation of optically anisotropic thin films. From analysis of variance analysis (ANOVA), the solution concentration was revealed as a main factor affecting the film thickness. The drying temperature and solution concentration were main factors affecting the transmittance of parallel direction ($T_o$). Especially, SY-FCF aqueous solution with high concentration induced a better alignment of LC columns and produced highly oriented anisotropic films. In this study, optically anisotropic films prepared by 33 wt% of SY-FCF in aqueous solution showed 89.7~98.7% of degree of polarization.

• Korean Journal of Optics and Photonics
• /
• v.33 no.2
• /
• pp.59-66
• /
• 2022

A free-form Mueller matrix ellipsometer (MME) based on independent control of the azimuthal angle of each polarizing element is introduced. The azimuthal angles of the polarizer and the matching compensator which generate the optimum Stokes vectors of an incident beam are investigated for the polarization state generator, where the spectral responses of the retardation angle and transmittance ratio of a nonideal compensator are taken into account. Similarly, the azimuthal angles of the analyzer and the corresponding compensator are investigated for the polarization-state detector, to unambiguously determine the Stokes vector of the outcoming beam from the sample, and explicit expressions for the Stokes elements are derived. Since the suggested technique enables one to utilize a nonideal quarter-wave plate as the compensator for an MME, it will contribute to the construction and application of a Mueller matrix spectroscopic ellipsometer (MMSE) operating over a wide spectral range from deep ultra-violet to near infrared.