• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.4
• /
• pp.616-624
• /
• 2006

In this paper, the transfer characteristics of high frequency transmission line having defected ground structure (DGS) and lumped elements are described. When a DGS, which is a kind of periodic structure, is inserted into a transmission line, its equivalent inductance and capacitance elements are added to the characteristics of the standard transmission line. This generates resonance, 3dB cut-off frequency, low-pass, band rejection, and band pass characteristics, and causes a slow-wave and enlarged electrical length of the transmission line. In addition, if the DGS is combined by a lumped element such as resistor, capacitor, and inductor, the resonant and cut-off frequencies moves up or down and other changes occur in the transmission characteristics. The variation of the transmission characteristics is described with the qualitative prediction and measured data.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.1
• /
• pp.131-141
• /
• 2007

This paper proposes analysis on new equipment for power quality in electric railway. The proposed equipment consists of series inverter and parallel inverter. Each inverter is connected by capacitor as dc link. This structure can be compensated for active and reactive power in catenary through transformer. We verified the proposed equipment using the PSCAD/EMTDC and the calculation results from the proposed approach are widely described in the paper.

• Tunnel and Underground Space
• /
• v.12 no.3
• /
• pp.220-228
• /
• 2002

Thermal flow through jointed rock mass was analyzed by numerical methods. The effect of a single set of joints on the heat conduction was analyzed by one-dimensional model and compared with the analytical solution. When a joint is completely dry, the joint behaves as a thermal break inducing jumps in temperature distribution even at steady state. Therefore when joints are completely dry, individual joint has to be taken into consideration to get a good result. When joints are partially or fully saturated, the thermal conductivity of the joints increases drastically and the jumps in temperature distribution become less severe. Therefore the effect of joint in heat conduction can be well absorbed by continuum anisotropic model whose thermal properties represent overall thermal properties of the intact part and the discontinuities. Since the effect of joints becomes less important as the degree of the saturation increases, the overall thermal response of the rock mass also becomes close to isotropic. Therefore it can be concluded that a great effort has to be made to obtain a precise in-situ thermal properties in order to get a good prediction of the thermal response of a jointed rock mass.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.1
• /
• pp.79-87
• /
• 2013

A new modulation technique - correlative encoded FSK (CEFSK) - for use in power and bandwidth limited digital communication system is proposed. CEFSK is free of ISI and generates output signals which have a smooth and continuous phase transition and a reduced envelope fluctuation by keeping correlation between amplitude and phases of two subsequent symbols. In comparison to conventional one-bit differential detected (1DD) GFSK, the performance of the 1DD-CEFSK in a non-linearly amplified (NLA) channel impaired by additive white Gaussian noise (AWGN), ISI and IM, is analyzed via computer simulation. The simulation result shows that, in an NLA single-channel, 1DD-CEFSK provides a signal-to-noise ratio (SNR) advantage of up to 1.2dB and 0.8dB at BER of $1{\times}10^{-4}$ when input back-off (IBO) of HPA is -1.0dB and -3.0dB, respectively. For the same channel environment with multi-channel, 1DD-CEFSK outperforms 1DD-GFSK by 1.1dB in SNR, regardless of the value of IBO.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.12
• /
• pp.39-48
• /
• 2001

We have studied the design of the photonic bandgap (PBG) structure on the microstrip line that can effectively control the fractional bandwidth of the passband formed in the stopband by adding the stub in the cell of the microstrip PBG structure. As the length of the stub increases, the cutoff frequency and the center frequency of the stopband are decreased, while the bandwidth of the stopband is increased. We have also found that the fractional bandwidth of the passband formed in stopband by the introduction of defect decreases as the stub length is increased. These results mean that adding the stub in the normal PBG structure is an effective way to control the fractional bandwidth. As an application example, we have implemented a microwave duplexer using the proposed structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.888-895
• /
• 2004

This paper proposes new miniaturization method of parallel coupled line filter by using capacitors and grounding. Proposed method can reduce resonator size by using only a small number of capacitor and grounding of parallel coupled line filter which is conventional in field of RF filters because of its design and fabrication simplicity. This paper applies the miniaturization method of transmission line and parallel coupled line to parallel coupled line filter, and presents that grounding can reduce the number of shut capacitors. Presented miniaturized method has merits of miniaturization of parallel coupled line, harmonic suppression, and improvement of high frequency skirt with harmonic suppression. For verification of proposed method, this paper presents a hairpin filter, which has 900 MHz center frequency and 10 % FBW, miniaturized to λ/4 by proposed method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.747-756
• /
• 1999

In this paper, we analyzed microwave-DC conversion efficiency for the dual-polarization rectenna and antenna position changing. And then we analyzed and applied Square-Loop FSS structure for reducing the diode harmonic components as a rectifying circuit. The results of microwave-DC conversion efficiency for the each of designed dual-polarization rectenna has 69.1% with $360\Omega$ (dipole type) and 75.4% with $340\Omega$ (patch type) optimum load resistor. When the each of dual-polarization rectenna has a optimal load resistor, it's conversion efficiency shows of $\pm$20% in dipole type and $\pm$5% in patch type at $0~180^{\circ}$position. When applied Square-Loop FSS structure for Rectenna, Insertion loss was under 1 dB as the passband and over 20 dB as the stopband. The microwave -DC conversion efficiency was represented good properties of $\pm$2% variation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.206-212
• /
• 2007

In this paper, a novel power/ground plane using the hybrid-cell electromagnetic band-gap(EBG) structure is proposed for the wide-band suppression of the ground bound noise(GBN) or simultaneous switching noise(SSN). The -30 dB stopband of the proposed structure starts from a few hundred MHz where the GBN/SSN energy is dominant. The distinctive features of this new structure are the thin spiral strip line and hybrid-cells. They realize the enhanced inductance and the shorter period of the EBG lattice. As a result, the lower cut-off frequency and bandwidth of the -30 dB stopband becomes lower and wider, respectively. In addition, the proposed structure has smaller number of resonance modes between power/ground planes and performs a low EMI behavior compared with the reference board.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.2
• /
• pp.230-235
• /
• 2008

Recently, LG chemical corporation developed new material called HYPERIER, which has an excellent barrier characteristic. It has many layers which are made of nano-composite within LDPE(Low-Density Poly Ethylene). In order to guarantee the quality of the final product from the production line, a certain test equipment is required to investigate the existence of layers inside the HYPERIER. In this work, ultrasonic sensor based test equipment for investigating the existence of inner layers is proposed. However, it is a tedious job for human operators to check the existence by just looking at the resounding waveform from ultrasonic sensor. Therefore, to enhance the performance of the ultrasonic test equipment, Fast Fourier Transform(FFT) and Principle Components Analysis(PCA) and Back-Propagation Neural Network(BPNN) are utilized which is used for classification of Quality. To verily the feasibility of the proposed scheme, some experiments are executed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.8
• /
• pp.1090-1098
• /
• 2018

Many short range weather radars with the low elevation search capability are needed for analysis and prediction of unusual weather changes or rainfall phenomena which occurs regionally. However, due to the characteristics of low elevation electromagnetic wave beam, it is highly probable that the received weather signals of these radars are seriously contaminated by the ground clutter. Therefore, the filter removing low Doppler frequency band is generally used to mitigate this problem. However, the phase noise in a radar system may limit the removal of the strong clutter and this may cause serious problems in estimating weather parameters because of the remaining clutter. Therefore, in this paper, the characteristics of phase noise in a radar system are investigated and the effects of the system phase noise are analyzed in the improvement of signal to clutter ratio for the strong clutter environment such as a short and low-elevated weather radar.