• Journal of Advanced Navigation Technology
• /
• v.18 no.1
• /
• pp.35-43
• /
• 2014

In this paper, it is about to non-contact wireless power transmission according to various conditions of self induction principle between the two planar coils at a transmission unit and a receiving unit based on the theory of wireless power transmission. The experiments are occurred in order to power transfer of noncontact method from designed wireless circuits in the primely coil and secondary coil, and the applying to Half Bridge Resonant converter transmission unit and receiving unit. and that were able to prepared circumstance to calculate of the output voltage and power source. The main power of the inductive coupling the resonant converter at the transmission unit is converted electrical energy using the solar cell module and artificial light source (halogen lamp) as a replace light and received 24 V power supply from solar power was used a input power source for the wireless power transmission device. Experimental results, to received of power is used to illuminate the lighting and to charge the battery in receiving circuit.And the wireless power transmission efficiency measured at the output side of the transmission unit is obtained about 70% to 89% compared to input power of receiving unit.In addition, efficiency were tested through ID verification method and comparing the phase difference between the voltage when foreign substances interfere with wireless power transmission.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.230-238
• /
• 2014

In this paper, we propose the possible way of accurate analysis and examination of ITO sensor to discriminate whether mutual capacitance ITO sensor is defective by using mutual capacitance of data in each node which consists of electrodes inside of ITO sensor. We have analyzed the structure characteristic of mutual capacitance ITO sensor which is used as an input device for not only small size electronics like mobile phone and tablets but also big size electronics and designed the circuit to inspect ITO sensor using touch screen panel IC. Set a variable related with mutual capacitance of charge and discharge and Implement to find and analyze accurate position when defect is made through the data from each node of ITO sensor. First, we can set a yield effective range through the first experiment data of mutual capacitance ITO sensor and by using the data of each node of ITO sensor which is the result from the second experiment, we can verify accuracy and effectiveness of effective range from the first experiment as a sample which is used in this experiment.

• Journal of Aerospace System Engineering
• /
• v.15 no.5
• /
• pp.81-88
• /
• 2021

In general, a non-explosive nylon wire cutting-based holding and release mechanism has been used to store and deploy deployable solar panels of CubeSat. However, with this method, accessing the solar panel's access port for charging the cube satellite's battery and electrical inspection and testing of the PCB and payloads while the solar panel is in storage is difficult. Additionally, the mechanism must have a reliable release function in an in-orbit environment, and reusability for stow and deploy of the solar panel, which is a hassle for the operator and difficult to maintain a consistent nylon wire fastening process. In this study, we proposed a pin-puller-based solar panel holding and release mechanism that can easily deploy a solar panel without cutting nylon wires by separating constraining pins. The proposed mechanism's release function and performance were verified through a solar panel deployment test and a maximum separation load measurement test. Through this, we also verified the design feasibility and effectiveness of the pin-puller-based separation device.

• Journal of Advanced Navigation Technology
• /
• v.26 no.3
• /
• pp.160-165
• /
• 2022

In this paper, we have proposed a magnetic resonant 6.78MHz WPT(wireless power transfer) technique which can be applied to a fixed transmitter and a receiver of varying relative distance and coil alignment, Power transmission characteristics are studied with the relative distance and misalignment ration of coil area between the transmitting and receiving coils. The coils are designed with the size of 60×80mm² by direct feeding method, and the characteristics are derived with the maximum relative distance of 50mm and horizontal area misalignment state of 0-40mm misalignment of coil center axis in the XY plane. The power transmission characteristics are compared between the 3D EM simulation and the measured data, and the power transmission shows larger than -3dB performance with the vertical distance of up to 30mm and 50% area misalignmment ratio. This work showsthe transmission characteristics according to relative distance and misalignment state between the cols and that direct feeding has advantage for the short relative distance and small misalignment ratio.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.105-111
• /
• 2024

The SLA (Stereolithography Apparatus) method is a type of 3D printing technique predicated on the transformation of liquid photocurable resin into a solid form through UV laser exposure, and its application is increasing in various fields. In this study, we conducted research to enhance the hydrophobicity and transparency of SLA 3D printing surfaces for microfluidic system production. The enhancement of surface hydrophobicity in SLA outputs was attainable through the application of hydrophobic coating methods, but the coating durability under different conditions varied depending on the type of hydrophobic coating. Additionally, to simultaneously achieve the required transparency and hydrophobic properties for the fabrication of microfluidic systems, we applied hydrophobic coatings to the proposed transparency enhancement method from prior research and compared the changes in contact angles. Teflon coating was proposed as a suitable hydrophobic coating method for the fabrication of microfluidic systems, given its excellent transparency and high coating durability in various environmental conditions, in comparison to titanium dioxide coating. Finally, we produced an Electrophoresis of Charged Droplet (ECD) chip, one of the digital microfluidics systems, using SLA 3D printing with the proposed Teflon coating method (Fluoropel 800). Droplet manipulation was successfully demonstrated with the fabricated chip, confirming the potential application of SLA 3D printing technology in the production of microfluidic systems.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.552-558
• /
• 2014

This paper suggests how to design a ZigBee-chip-based communication module to remotely measure radiation level. The suggested communication module consists of two control processors for the chip as generally required to configure a ZigBee system, and one chip module to configure a ZigBee RF device. The ZigBee-chip-based communication module for remote radiation measurement consists of a wireless communication controller; sensor and high-voltage generator; charger and power supply circuit; wired communication part; and RF circuit and antenna. The wireless communication controller is to control wireless communication for ZigBee and to measure radiation level remotely. The sensor and high-voltage generator generates 500 V in two consecutive series to amplify and filter pulses of radiation detected by G-M Tube. The charger and power supply circuit part is to charge lithium-ion battery and supply power to one-chip processors. The wired communication part serves as a RS-485/422 interface to enable USB interface and wired remote communication for interfacing with PC and debugging. RF circuit and antenna applies an RLC passive component for chip antenna to configure BALUN and antenna impedance matching circuit, allowing wireless communication. After configuring the ZigBee-chip-based communication module, tests were conducted to measure radiation level remotely: data were successfully transmitted in 10-meter and 100-meter distances, measuring radiation level in a remote condition. The communication module allows an environment where radiation level can be remotely measured in an economically beneficial way as it not only consumes less electricity but also costs less. By securing linearity of a radiation measuring device and by minimizing the device itself, it is possible to set up an environment where radiation can be measured in a reliable manner, and radiation level is monitored real-time.

• The Korean Journal of Rheology
• /
• v.11 no.1
• /
• pp.57-65
• /
• 1999

In order to measure yield stress of PIM feedstocks simply and effectively, a yield stress measuring technique was developed by a vane method. The vane method had an advantage that there was no wall-slip, while it had a drawback that it could not measure viscosity change at various shear rates. A Newtonian fluid was tested for the appropriateness of the measuring technique. The end effect of a vane was checked to produce an acceptable error. The torque peak has been considered to be developed at yielding of non-Newtonian fluids with yield stress. However, it was influenced very much by control system of the instrument so that the torque value at the stable region was taken to calculate yield stress. Torque at zero rotational speed was obtained by extrapolating the torque values at various speeds to remove the effect of the rotational drag. As general verification, yield stress of feedstocks made of Tungsten carbide powder with wax-based binder was measured at different temperatures and various powder concentrations.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.7
• /
• pp.4692-4697
• /
• 2014

A micro-grid including photovoltaic source and Li battery has been installed and operated for several years at the campus of USF and been used as a test bed. Photovoltaic power source has been strongly influenced by the location, weather and climate of the installed area. To compensate for the uncertainty of photovoltaic source's power output, a Li battery is connected directly to the photovoltaic source and supplies electric power to the grid. The Li battery is operated to supply power output to the grid according to the charging or discharging mode of the battery based on the average power output of the photovoltaic source, which is calculated from the monitored data for several years. The grid of the photovoltaic and Li battery system is operated as a severe loading condition and the operating characteristics of PV source and Li battery cells are analyzed in detail.

• Journal of Korea Multimedia Society
• /
• v.18 no.5
• /
• pp.652-662
• /
• 2015

It is necessary to develop small, implantable bio-telemetry systems which can measure and transmit patients' bio-signals from internal body to external receiver. When measuring bio-signals, like electrical bio-signals, acoustic bio-signal measurement has also a big clinical usefulness. But, sound signal has larger frequency bandwidth than any other bio-signals. When considering these issues, a wireless telemetry system which has rapid data transmission rate proportional to wide frequency bandwidth is necessary to be developed. The bluetooth module is used to overcome the data rate limitation caused by the large frequency bandwidth. In this paper, a novel multimedia bluetooth biotelemetry system was developed which consists of transmitter module located in the body and receiver device located outside of the body. The transmitter consists of microphone, bluetooth, and wireless charging device. And the receiver consists of bluetooth and codec system. The sound inside the skin is captured by microphone and sent to receiver by bluetooth while charging. The wireless charging system constantly supplies the electric power to the system. To verify the performance of the developed system, an in vitro experiment has been performed. The results show that the proposed biotelemetry system has ability to acquire the sound signals under the skin.

• Journal of Broadcast Engineering
• /
• v.20 no.2
• /
• pp.215-223
• /
• 2015

Energy harvesting technique is an energy charging technique for communication device in energy-constrained environment. Recently, energy harvesting technique that harvests energy from wireless radio frequency signal is proposed. Representatively, there are time switching technique and power splitting technique. This paper proposes an optimal harvesting time allocation scheme in a wireless cognitive relay network when secondary user relay uses energy harvesting technique to transmit information. Secondary user relay receives information and energy simultaneously from the secondary user source's signal via time switching technique. We aim to maximize the instantaneous throughput by optimizing harvesting time of the secondary user relay. Simulation results show that using optimized harvesting time gets larger instantaneous throughput compared to using constant harvesting time.