• Journal of Energy Engineering
• /
• v.16 no.4
• /
• pp.181-186
• /
• 2007

In order to investigate the heat transfer coefficient and pressure drop during evaporation of $CO_2$, basic experiment on the evaporation heat transfer characteristics in a horizontal smooth tube was performed. The experimental apparatus consisted of a test section, a DC power supply, a heater, a chiller, a mass flow meter, a pump and a measurement system. Experiment was conducted for various mass fluxes ($200{\sim}1200\;kg/m^2s$), heat fluxes ($10{\sim}80\;kW/m^2$) and saturation temperatures ($-5{\sim}5^{\circ}C$). With the increase of quality, the evaporation heat transfer coefficient decreased. With the increase of heat flux, the evaporation heat transfer coefficient increased. Significantly change of the heat transfer coefficient was observed at any heat flux and mass flux. With the increase of saturation temperature, the heat transfer coefficient increased. Pressure drop increased with the increase of mass flux and the decrease of saturation temperature.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.4
• /
• pp.313-322
• /
• 2019

This study is to compare and analyze the physical and strength properties of lightweight concrete using domestic lightweight aggregate by replacement ratio of artificial lightweight fine and coarse aggregate after considering low cement mixture and pre-wetting time. The slump, unit weight, compressive strength and split tensile strength of lightweight concrete with domestic lightweight aggregate were measured. As test results, the slump of lightweight concrete by replacement ratio of lightweight fine aggregate increased as the replacement ratio of lightweight fine aggregate increased. The unit weight of lightweight concrete using 100% of lightweight fine aggregate was about 10.4% lower than that of the lightweight concrete with natural sand. In addition, the unit weight of lightweight concrete by replacement ratio of lightweight coarse aggregate increased with the increase of the ratio of LWG10(5~10mm). The compressive strength of lightweight concrete with lightweight fine and coarse aggregate increased as the replacement ratio of lightweight fine aggregate increased. The compressive strength of lightweight concrete with natural sand and LWG10 was 30 to 31MPa regardless of the replacement ratio of the lightweight coarse aggregate after 7 days.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.12
• /
• pp.1091-1097
• /
• 2011

In the present study, TMD(tuned mass damper) with eddy current damping is proposed to suppress the vibration of a cantilever beam effectively. The advantages of TMD are that it is simple and its performance are excellent at any particular frequency. However, TMD may have the low performance at other frequency. To solve this problem and improve its performance, this study applies the eddy current damping to TMD. This TMD with ECD is named as MTMD(magnetically tuned mass damper). MTMD is designed for the vibration suppression of a cantilever beam. The mathematical modeling, simulation, and experiments of the cantilever beam with MTMD are performed. From analytic and experimental results, it can be concluded that the vibration suppression performance of MTMD are excellent.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.1
• /
• pp.40-47
• /
• 2015

Dynamic response of any small structure is always affected by the mass of the attached accelerometer. This paper predicts the natural frequencies and frequency response functions by removing the mass loading effect from the accelerometer. This mass loading is studied on a simple cantilever beams by varying the location of accelerometer. By using sensitivity analysis with iteration method, accelerometer mass and location are obtained. The predicted natural frequencies of the small cantilever beam without the accelerometer's mass show good agreement with the structural re-analysis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1247-1252
• /
• 2007

The machine equipment of the building inside occurs the vibration. In order to reduce this vibration spring, rubber pad is used. But efficiency of this classical mount is restricted at specific frequency. Also maximum efficiency design is complicated. This paper proposes and examines a attached mass isolation system that is used to reduce transmitted vibrations from machines onto their floor support. With attached mass the low frequency performance is improved overall. The performance is showed in 2 degree of freedom model test. And the proposed isolator has been validated by dynamic test and good agreement between theoretical and experimental results has been obtained.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.4 s.19
• /
• pp.114-124
• /
• 2004

In this paper, we have proposed a novel method which can analysis a rotating elastically restrained blade with concentrated masses located in an arbitrary position. 1:he equations of motion are derived and transformed into a dimensionless form to investigate general phenomena. For the modeling of the multi-concentrated masses, the Dirac delta function is used for the mass density function. Simulation results show that the vibration characteristics of elastic restrained blade of according to dimensionless variables for example, multiple masses magnitude and mass location ratio. This method can be applied to an practical rotating blade system required to more accurate results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.270-275
• /
• 2003

The nonlinear dynamic characteristic of a straight tube conveying fluid with constraints and an attached mass on the tube is examined in this study. An experimental apparatus composed of an elastomer tube conveying water which has an attached mass and constraints is made and comparisons are done between the theoretical results from non-linear equation of motion of piping system and experimental results. And the results show that the tube is destabilized as the mass of the attached mass increases, and stabilized as the position of the attached mass close to the fixed end. In case of a small end-mass, the system shows rich and different types of periodic solutions. For a constant end-mass, the system undergoes a series of bifurcations after the first Hopf bifurcation, as the flow velocity increases, which causes chaotic motion of the tube eventually.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.723-726
• /
• 2011

전 세계적으로 사회기반시설 및 신재생 에너지 생산을 위한 공간부족 문제를 해결하기 위하여 초대형 부유구조물에 대한 관심이 증가하고 있다. 다양한 사용분야에 대한 안정성 확보를 위해 파랑하중에 의한 동적 응답과 부유체의 강성 대비 길이 효과로 인해 발생할 수 있는 특이 거동에 대한 분석이 필요하다. 초대형 부유구조물의 경우 중앙부에 비해 양끝 단에서 과도한 응답이 발생하며, 이를 해결하기 위해 입사파가 들어오는 초대형 부유구조물의 단부에 부착되는 다양한 감요장치(anti-motion device)가 제안되어지고 있다. 초대형 부유구조물에 감요장치가 적용될 경우 입사파에 의한 동적 파압을 감소시켜 구조물의 전반적인 응답을 줄여줄 수는 있지만 감요장치의 질량이 클 경우 오히려 끝단의 응답을 증폭시킬 수 있다. 본 논문에서는 양단 자유 경계조건의 탄성지지된 보를 이용하여 초대형 부유구조물의 길이와 끝단에 부착된 감요장치의 질량으로 인한 영향을 분석하였다.

• Journal of Power System Engineering
• /
• v.4 no.4
• /
• pp.65-69
• /
• 2000

On the dynamic behavior of a simple beam subjected to an uniformly distributed tangential follower force, the influences of the velocities and magnitudes of a moving mass have been studied by numerical method. The instant amplitude of a simple beam is calculated and analyzed for each position of the moving mass represented by the time functions. The uniformly distributed tangential follower force is considered within its critical value of a simple beam, and four values of velocity is also chosen. Their coupling effects on the deflections of a simple beam are inspected too. When a moving mass moves after middle zone of a simple beam at the low velocities, its deflection is increased by the coupling of an uniformly distributed tangential follower force and moving mass.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.2
• /
• pp.25-36
• /
• 2000

본 논문에서는 구조물이 과도한 기진력을 받을 때에 구조물의 진동 제어를 위하여 제안 되어진 여러 가지 포화 제어 알고리듬들의 유용성을 실제적인 관점에서 살펴보았다 제안된 포화 제어 알고리듬 중세서 수정된 뱅뱅 제어 알고리듬이 매우 유용한 것임을 확인할 수 있었으나 이는 제어력 파형 결정 파라미터의 어떤 범위내에서만 효과적이며 그 범위를 넘어서는 경우에 있어서는 제어기를 불안정하게 할 수 있음을 확인할 수 있었다 따라서 수정된 뱅뱅 제어 알고리듬의 적용시에 과도한 외부 기진력에 대하여 제어기의 안정적인 작동에 의한 구조물의 진동제어효과를 얻기 위해서 제어력 파형 파라미터를 과도 기진력의 크기에 따라 변화시키는 적응형의 방법을 제안하였고 이의 유용성을 수치실험 및 유압식 질량 감쇠기를 장착한 축소 구조물 검증 실험을 통하여 확인하였다.