• Journal of the Korean institute of surface engineering
• /
• v.18 no.3
• /
• pp.125-133
• /
• 1985

About 1 mm thick nickel electrodeposits were obtained from nickel sulphamate baths at 40 to 60$^{\circ}C$ over the range of current densities form 5 to 25 A/$dm^2$. Deposits from above about 1.2V of cathode overpotential had randomly distributed fine grains due to a higher nucleation rate and hence had a high hardness. A deposit obtained at 0.63 V had the [110] orientation with a field oriented fine structure which yield a relatively high hardness. Deposite obtained at the intermediate overpotentials showed the [100] orientation with coarse field oriented structure whose column width tended to decrease with increasing cathode overpotential, which, in turn, gave rise to an increase in hardness. Residual stresses of the deposits measured by X-ray technique were mostly tensile but did not exceed 80 MPa, and were occasionally very small compressive. The cathode current efficiency was above 90% in all the electrolysis conditions, whereas the anode current efficiency varied from 50 to 90% with current density, bath temperature and nickel chloride concentration, among which the chloride was the most influential.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.308-308
• /
• 2012

Electrodeposition of thermoelectric materials, including binary and ternary compounds, have been attracting attentions, because its many advantages including cost-effectiveness, rapid deposition rate, and ease of control their microstructure and crystallinity by adjusting electrodeposition parameters. In this work, $Bi_xTe_y$ films were potentiostatically electrodeposited using Au/Ni(80/20 nm)/Si substrate as the working electrode in solutions consisting of 10mM $TeO_2$ and 1M $HNO_3$ where $Bi(NO_3)_3$ was varied from 2.5 to 10 mM. Prior to electrodeposition potentiostatically, linear sweep voltammograms (LSV) were acquired with a standard three-electrode cell. The $Bi_xTe_y$ films deposited using the electrolyte containing low Bi ions shows p-type conductivity, which might be attributed by the large incorporation of Te phases. Near stoichiometric $Bi_2Te_3$ thin films were obtained from electrolytes containing 5mM $Bi(NO_3)_3$. This film shows the maximum Seebeck coefficient of $-100.3{\pm}12.7{\mu}V/K$. As the increase of Bi ions in electrolytes decreases the Seebeck coefficient and resistivity. The maximum power factor of $336.2{\mu}W/m{\cdot}K^2$ was obtained from the film deposited using the solution of 7.5mM $Bi(NO_3)_3$.

• Resources Recycling
• /
• v.30 no.6
• /
• pp.76-82
• /
• 2021

The separation of palladium from crude metal, which is obtained from electronic waste using pyrometallurgy was achieved through electrolysis. This was done to recover high-purity copper. The oxidation potentials of these metals are a fundamental part of the analysis of electrolytic separation of palladium and impurity metals. To achieve this, copper, iron, and nickel were dissolved in the electrolyte, and palladium and aluminum were found to be recoverable from anode slime. During the electrolysis for palladium separation, palladium was present in the anode slime and was obtained with a recovery of 97.46 % indicating almost no loss. 4N-grade copper was recovered from the electrodeposition layer at the cathode.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.227-232
• /
• 2019

Heat pump systems based on ocean thermal energy conversion (OTEC) systems use the temperature difference between deep ocean water and surface ocean water to operate. However, they may have heat transfer degradation due to corrosion on the heat exchanger surface due to the salinity of sea water. This study presents experimental results for the heat transfer decrease of corroded metal tubes with respect to corrosion time. In order to replace high-priced titanium, electro-deposition (ED) coating was performed on aluminum tubes. Aluminum tubes with ED coating thicknesses of 10, 15, and $20{\mu}m$ were tested for double-tube heat exchangers after performing accelerated corrosion for 6, 12, and 18 weeks. The effects of the coating thickness and the corrosion time on the heat transfer degradation were investigated. From the results, the aluminum tube with an ED coating of $20{\mu}m$ thickness can be suggested as a candidate for replacing titanium tubes.

• Journal of the Korean Electrochemical Society
• /
• v.25 no.2
• /
• pp.51-68
• /
• 2022

Although lithium metal batteries have a high energy density, experimental skills capable of solving lots of problems induced by dendrite such as short circuit, low coulomb efficiency, capacity loss, and cycle performance are still only in academic research stage. In this paper, research cases for dendrite growth inhibition on lithium metal electrode were classified into four types: flexible SEI (solid electrolyte interface) layer responding to volume expansion of lithium metal electrode, SEI supporting layer to inhibit dendrite growth physically, SHES (self-healing electrostatic shield) mechanism to adjust lithium growth by leading uniform diffusion of Li⁺ ions, and finally micro-patterning to induce uniform deposition of lithium. We hope to advance the practical use of lithium metal electrode by analyzing pros and cons of this classification.

• Journal of the Korean institute of surface engineering
• /
• v.55 no.3
• /
• pp.180-186
• /
• 2022

The production of hydrogen via water electrolysis (i.e., green hydrogen) using renewable energy is key to the development of a sustainable society. However, most current electrocatalysts are based on expensive precious metals and require the use of highly purified water in the electrolyte. We demonstrated the preparation of a non-precious metal catalyst based on CuCo₂O₄ (CCO) via simple electrodeposition. Further, an optimization process for electrodeposition potential, solution concentration and electrodeposition method was develop for a catalyst-substrate integrated electrode, which indicated the highly electrocatalytic performance of the material in electrochemical tests and when applied to an anion exchange membrane water electrolyzer.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.52-57
• /
• 2010

Although chemical sedimentation and ion exchange are usually applied to the treatment of heavy metal ions and radioactive cations, they have some serious disadvantages like a great consumption of chemicals, the disposal of valuable metals, and the secondary pollution of soil by the solid-waste. The advanced countries recently have studied the electrochemical ion exchange, combined electrochemical reduction and ion exchange, for the development of the alternative technique. This study has been performed to investigate the optimum condition for the preparation of the nickel hexacyanoferrate (NiHCNFe) which is an electrochemical ion exchanger. NiHCNFe film was deposited on the surface of nickel plate by chemical method or electrochemical method. The morphology and composition of NiHCNFe were observed by SEM and EDS, respectively. The peak current density of NiHCNFe was measured from the cyclic voltammograms of the continuous oxidation-reduction reaction in a parallel plane ion exchange electrode reactor. It was found that the chemical preparation method was better than the electrochemical method. The concentrated NiHCNFe was apparently deposited on nickel plate when dipping in the preparing solution for 118 h, especially. It also had a best durable performance as an ion exchange electrode.

• Korean journal of applied entomology
• /
• v.16 no.1 s.30
• /
• pp.47-53
• /
• 1977

Bacterial diseases of soybean has been recognized as a limiting factor of soybean production in Korea as it was estimated to cause around 10 percent of yield losses annually. The purpose of the study is to obtain information on the diseases through proving the kinds of pathogens and epidemiology, The wire brush method and multineedle appeared to be the best way of inoculation under all circumstances. Wire brush method, especially, was effective in shortening the incubation period and manifesting the lesion development by introducing more inoculum per unit of area. In case of spray inoculation it was necessary to apply a small amount(1 : 1,000) of wetting agent, twin-20, otherwise it was unabled to produce the diseases under field conditions. Two kinds of bacterial diseases caused by Pseudomonas glycinea and Xanthomonas phaseoli var. sljense were found from surveyed areas in Kore. Wild fire disease on soybean caused by Pseudomonas tabaci had not detectable during the experiment although there were several reports on the disease from other countries. when the pathogens were introduced into sterile soil, bacterial leaf blight pathogen could exsisted until 30 days while bacterial pustule pathogen survived only 4 days under the natural conditions of later June. Both bacteria, however, could produce the disease after more than 10 months period of storage in refrigerator when they were exsisted in infected plant tissues. In warehouse, non-temperature controlled, the bacteria lose their infectability within 6 months period from October to April even though they exsisted in infected tissues. Surface infested seeds with the pathogens could not produced the diseases on seedling stages of soybean plants when the seeds were planted in sterile soil after inoculation by dipping the seeds into bacterial suspensions, although germination was depressed by the pathogens when the seeds were planted on agar media.

• Resources Recycling
• /
• v.21 no.5
• /
• pp.31-37
• /
• 2012

As a recovery of elemental silicon from the sludge of Si wafer process, a process of mechanical separation-chlorine roasting-electrolysis has been suggested. The silicon sludge consisted of Si, SiC, machine oil, and metallic impurities. The oil and metal impurities was removed by mechanical separation. The Si-SiC mixture was converted to silicon chloride by chlorine roasting at $1000^{\circ}C$ for 1 hr and the silicon chloride was dissolved into an ionic liquid of $[Bmpy]Tf_2N$ as an electrolyte. Cyclic voltammetry results showed an wide voltage window of pure $[Bmpy]Tf_2N$ and a reduction peak of elemental Si from $[Bmpy]Tf_2N$ dissolved $SiCl_4$ on Au electrode, respectively. The silicon deposits could be prepared on the Au electrode by the potentiostatic electrolysis of -1.9 V vs. Pt-QRE. The elemental silicon uniformly electrodeposited was confirmed by various analytical techniques including XRD, FE-SEM with EDS, and XPS. Any impurity was not detected except trace oxygen contaminated during handling for analysis.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.4
• /
• pp.321-332
• /
• 2017

In order to build a general model of a high-throughput uranium electrorefining process according to the electrode configuration, numerical analysis was conducted using the COMSOL Multiphysics V5.3 electrodeposition module with Ordinary Differential Equation (ODE) interfaces. The generated model was validated by comparing a current density-potential curve according to the distance between the anode and cathode and the electrode array, using a lab-scale (1kg U/day) multi-electrode electrorefiner made by the Korea Atomic Energy Research Institute (KAERI). The operating temperature was $500^{\circ}C$ and LiCl-KCl eutectic with 3.5wt% $UCl_3$ was used for molten salt. The efficiency of the uranium electrorefining apparatus was improved by lowering the cell potential as the distance between the electrodes decreased and the anode/cathode area ratio increased. This approach will be useful for constructing database for safety design of high throughput spent nuclear fuel electrorefiners.