• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2503-2508
• /
• 2014

This study is about the selection and noise test of electronic sensor which is preceded by electric Operating Cell(EOC) development using electronic sensor technology to solve the structural weakness of Mechanism Operated Cell(MOC) in VCB, and has a final target in product development minimizing contact malfunction of the chattering or rebounce states caused by existing MOC. In this test results, when opening and closing VCB, rising velocity of surge voltage in opening time was measured 4.2 times faster than closing time and noise decibel value was measured respectively 120dB and 110dB. When supplying 60kV power frequency overvoltage, we found that sensor output graph in VCB opening and closing times operated stably without distortion. When supplying 150kV $1.2{\times}50{\mu}s$ impulse frequency voltage, we found that voltage graph of output contact in sensor opening and closing sides maintained a normal condition without distortion, and when supplying 2500A current, we found that tested result of electric field noise operated stably without distortion.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.5
• /
• pp.73-79
• /
• 2008

This paper presents a simple electronic starter for single phase induction motor (SPIM). It replaces the centrifugal switch in the auxiliary winding circuit of the capacitor start type SPIM. The electronic starter observes the auxiliary winding voltage, and disconnects the auxiliary winding when the motor gets close to its rated speed. Because of its possibly fluttering contacts of the centrifugal switch which mounted on the conventional SPIM, the reliability of SPIM can be reduced. Developed new electronic starter has no mechanical contacts. Therefore, the reliability and the performance of SPIM can be improved. The operational principle of the proposed electronic starter is explained, and illustrated with experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.164-169
• /
• 2005

A.T.S.의 스위칭 구조와 접점 환경은 주로 아크 전류, 접촉 저항, 아크 시간 등의 불리적 요인이 주로 마모와 특성에 영향을 미치게 된다. 사용되는 접점 재료는 W 또는 WC-Cu 계로 형상과 크기는 전형적인 반구형 구조의 접촉으로 구동이 이루어진다. 따라서 A.T.S.용 접점의 아크 마모 특성 시험을 위한 고려 요인은 이러한 점을 고려하여 시험과 분석이 이루어 졌다. 접점의 마모 특성 실험식으로부터 실제적인 관점에서 보면 제한된 수명을 나타내는 $n_L$을 보장하기 때문에 b<1의 경우가 가장 바람직한 결과로 ATS 접점 시편의 경우 $b{\fallingdotseq}0.99$로 안정된 접점 아크 마모 특성을 갖는 것으로 판단된다. 아크 전압에 대한 모델링과 실험에서 접점 간극 거리 1<0.1mm, 아크전류 i<100A의 시험 조건에 대해 검토한 결과 ATS 접점 시편의 아크전압은 $u_a=10.2V$로 계산되었다. 이 값은 설험적인 값과 상당히 접근하는 특성을 갖는 것으로 나타났으며, 아크에 의한 마모를 억제하기 위해 첨가하는 WC 또는 W의 복합 소결로 인해 아크 에너지가 감소되는 것을 보여준다. 한편 접점의 아크 동작이 분리되는 순간의 동작 시험에서 기존 W(50%wt)-Cu(50%wt) 접점의 값과 비교하면 분리시 아크 전압은 상대적으로 낮아지는 현상은 W강화 첨가량의 증가로 인한 아크 에너지 감소의 제한성을 나타내는 것으로 사료된다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.4
• /
• pp.1-7
• /
• 2000

In this paper, we study a cause of malfunction of switch to control drive motor in DFMS(Digital Flux Mapping System) which can measure incore neutron flux of the nuclear plant, and develope a method to solve this problem. DFMS has the type of generating contact signal by mechanical switch lever, which is operated whenever thimble detector inserted or withdrawed through thimble Guide Tube. However the characteristics of the lever tend to be changed by mechanical degrade or bad environment and the lever finally generates errotic contact signal. Therefore we installed electric coil ass'yin the outside of Guide Tube instead of mechanical switch assy's. In addition we applied resonance effect to control circuit and installed condenser in the input of power supply to protect noise and interference. After completion of this improvement, we tested this improved device repetitively under the various conditions. In conclusion, we identified the generation of the desired contact signal and the prevention of detector failure through plant surveillance test during normal plant operation.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.50-51
• /
• 2011

본 논문에서는 영구자석 동기발전기(PMSG)의 전압 및 역률 보상을 위한 기계식 접점을 가지는 조상기의 문제점을 개선하기 위해 전자회로 방식을 채택하여 제어회로에 마이크로프로세서를 사용, 회로를 최소화하고 접점 부분은 전자적인 스위칭소자(MOSFET)를 사용함으로써 조상기의 신뢰성과 특성을 개선할 수 있는 시스템을 제안하고 시뮬레이션을 통해 그 타당성을 검증한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.216-223
• /
• 2006

The high efficiency full-bridge LLC resonant converter using a contact-less transformer Is proposed for the photovoltaic power generation system. For the series resonance with a series capacitor, the LLC resonant converter utilizes the leakage inductance and magnetizing inductance of a contact-less transformer Unlike the conventional series resonant converter operated to the continuous resonant current at above resonance frequency, the proposed converter operates to the discontinuous resonant current at the narrow frequency control range below resonance frequency. Due to the discontinuous mode resonant current, the proposed converter can be achieved the zero voltage switching (ZVS) in the primary switches and the zero current switching (ZCS) in the secondary rectification diodes without my auxiliary circuit. In this paper, the experimental results of the proposed full-bridge LLC resonant converter using a contact-less transformer are verified on the simulation based on the theoretical analysis and the 150W experimental prototype.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.17 no.5
• /
• pp.15-21
• /
• 1980

An engine control system in which the conventional mechanical ignition system is studied. The contact point of the breaker is replaced by the contactless magnetic pick up sensor from which the information of the speed and the position of the crankshaft is extracted , and further an electronic High Energy Ignitim System Is designed, implemented and tested . The High Energy Igniticwl System increases the secondary spark voltage of the ignition coil from the conventional 10000~15000 volts to the 30000~40000 volts resulting in improving the combustion efficiency. Also, instead of the conventional advimce mechanism forigniliontiming control, a microprocessorbased timinng mechanisn is installed to determine the ignition timing data in response to the engine rpm and the intake manifold vacuum.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.914-915
• /
• 2011

최근 지구온난화의 문제점으로 저 탄소 친환경 자동차로 배터리 전력과 가솔린 엔진을 같이 사용하는 하이브리드 자동차가 주목 받고 있다. 최근에 개발되고 있는 하이브리드 자동차는 전력의 효율적인 사용을 위해 배터리의 전압이 증가되고 있고 이에 따라 DC High Voltage를 다룰 수 있는 Relay의 용량이 요구된다. 이런 측면에서 하이브리드 자동차에 사용되는 EV-Relay의 경우 소형화에 따른 문제점이 발생한다. 그 대표적인 문제점으로 EV-Relay의 접점에 일시적인 과전류가 흐르면서 전기적 반발력이 발생하여 EV-Relay의 폭발과 같은 위험한 문제점이 발생 할 수 있다. 이에 따라 본 논문에서는 Relay에서 발생하는 전기반발력의 힘을 MAXWELL프로그램을 통해 모의하는 연구를 하였다.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.3
• /
• pp.130-137
• /
• 2015

This study is about the controller development of the Electric Operating Cell(EOC) which will replace the Mechanical Operated Cell(MOC) of the vacuum circuit breaker which has been used in the power plant and the performance test for the developed controller. The controller developed through this study was manufactured considering the harsh installation environment and electrical condition of the power plant, and the controller performance certification test for confirming the product reliability was taken to know whether or not to withstand fully in various electrical and mechanical problems. Items for performance certification test were AC power frequency voltage withstand test, combined surge immunity test, 1 [MHz] oscillatory SWC test, fast transient SWC test, radiated electromagnetic interference test, vibration test. As a result, all tests has passed an examination without malfunction.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.5
• /
• pp.700-706
• /
• 2012

The core technology of a starting device in the packaged power system is the pinion gear shifting device and to limit the initial starting voltage. Although the conventional products have been used the starting controller using mechanical contactor, these have a big problem such as the uncertainty for the start of starting motor after a pinion gear is completely shifted or the arc demage due to high current. In this study, in order to solve these problems, we designed and fabricated a new product to achieve the safety and reliability as follows: the pinion gear-shifting control circuits to eliminate the uncertainty of the start, the starting control system using semiconductor device to prevent the arc demage of contactor caused by high current, a start safety devices for soft starting of series motor. In addition, we obtained the electrical safety by separating the pinion gear control circuit and the source circuit of motor.