• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.5 s.335
• /
• pp.31-38
• /
• 2005

The architecture and the implementation details of a UTMI(USB2.0 Transceiver Macrocell Interface) compatible USB2.0 transceiver chip were presented. To confirm the validation of the incoming data in noisy channel environment, a squelch state detector and a current mode Schmitt-trigger circuit were proposed. A current mode output driver to transmit 480Mbps data on the USB cable was designed and an on-die termination(ODT) which is controlled by a replica bias circuit was presented. In the USB system using plesiochronous clocking, to compensate for the frequency difference between a transmitter and a receiver, a synchronizer using clock data recovery circuit and FIFO was designed. The USB cable was modeled as the lossy transmission line model(W model) for circuit simulation by using a network analyzer measurements. The USB2.0 PHY chip was implemented by using 0.25um CMOS process and test results were presented. The core area excluding the IO pads was $0.91{\times}1.82mm^2$. The power consumptions at the supply voltage of 2.5V were 245mW and 150mW for high-speed and full-speed operations, respectively.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.2 s.314
• /
• pp.1-11
• /
• 2007

H.264/AVC uses variable block sizes to achieve significant coding gain. It has 7 different coding modes having different motion compensation block sizes in Inter slice, and 2 different intra prediction modes in Intra slice. This fine-tuned new coding feature has achieved far more significant coding gain compared with previous video coding standards. However, extremely high computational complexity is required when rate-distortion optimization (RDO) algorithm is used. This computational complexity is a major problem in implementing real-time H.264/AVC encoder on computationally constrained devices. Therefore, there is a clear need for complexity reduction algorithm of H.264/AVC such as fast mode decision. In this paper, we propose a fast mode decision with early $P8\times8$ mode rejection based on block size activity using large block history map (LBHM). Simulation results show that without any meaningful degradation, the proposed method reduces whole encoding time on average by 53%. Also the hybrid usage of the proposed method and the early SKIP mode decision in H.264/AVC reference model reduces whole encoding time by 63% on average.

• Journal of the Korean School Mathematics Society
• /
• v.6 no.1
• /
• pp.65-85
• /
• 2003

The purpose of this research is to increase mathematical problem solving abilities VIa STAD evaluation after completing classes. to which ST AD group study is applied, and promoting the learning accomplishments of students by developing gradual self-leading learning materials about the research project on ' How to use an hour math class efficiently\ulcorner ' For this purpose, the items below were studied. Firstly, gradual self-leading learning materials were developed and applied which were composed of textbook abstracts, basic problems, developing problems and intensive problems rather than existing textbooks. Secondly, the ST AD group study model was selected and applied which invokes competitions among small groups of which learning goals were clear. individual responsibility was important. and successive opportunities were equal. The evaluation using STAD at each end of a chapter was announced instantly using the EXCEL scoring system. Though the results of experimental classes were limited in their size. experimental time, and class selection, there were meaningful changes in the aspect of being able to heighten the accomplishment desire of students by inducing voluntary competitions among small groups without any student omitted. As the result of applying this research to my class, the ST AD group study using gradual self-leading learning materials invoked the interests of students and increased learning accomplishments via increasing problem solving abilities in mathematics. The ST AD group study was easy to use by beginning teachers, and its process was simple. It increased interactions among students and learning motives because its compensation system was open to all students. Among various studying methods for small groups. STAD group study is expected to be widely used for mathematics classes.

• Applied Microscopy
• /
• v.35 no.1
• /
• pp.15-22
• /
• 2005

Metallothionein (MT) is a low molecular weight, cysteine-rich, metal-binding, and non-enzymatic protein. The present study was carried out to investigate the expression of MT gene as well as the localization of MT in regenerating rat liver. In partial hepatectomized rats, MT mRNA was detected as early as 1 hr and reached a maximal level by 8 hr after the operation. Thereafter, this level decreased gradually until 24 hr, and it became similar to that of sham control. Meanwhile, time course of MT immunoreactivity using immunogold-labelling revealed that the number of gold particles in hepatocytes increased significantly by 12 hr, but decreased at 48 hr after partial hepatectomy. Ultrastructurally, immunogold particles indicating the presence of MT were distributed in both the cytoplasm and the nucleus of the rat hepatocytes, particularly the particles were distributed at rough endoplasmic reticulum and nucleolus and did not seem to adhere to mitochondria or lysosomes in proliferating hepatocytes. Briefly, high level of MT mRNA expression and the intense immunoreactivity and/or the specific localization of MT was observed during liver regeneration. These results suggest that MT possibly involves hepatocyte proliferation via the storage or the supply of various metal ions in the regenerating rat liver.

• Korean Journal of Childcare and Education
• /
• v.9 no.2
• /
• pp.23-46
• /
• 2013

The purpose of this study was to obtain basic information for novice teachers' adjustment. The data from five novice teachers were collected by in-depth interviews of each subject, as well as reviewing a memo diary, journal and class diary. The results indicated that the novice teachers' experiences were categorized into difficulties in social relationships, heavy workload, stress related to making mistakes, obtaining support and assistance, adequate understanding of their field of work and so on. The model theory for their process of adjustment was found by grounded theory approach. The causal conditions include mistakes in performance of work and immaturity of managing social relationships. The contexts include age of the children, work conditions(i.e. time and space), amount of workload, unfamiliarity of new work assignments, personalities of colleagues, and high frequency of meeting parents of children. The intervening conditions are composed of a guidance program for novice teachers, support from colleagues, work rewards, and the personalities of novice teachers. The novice teacher use three strategies: trying to ignore, sharing difficulties and accessing support from friends or family, as well as willful efforts to transfer negative emotions into positive ones. The consequences of the strategies include: successful career progression, survival, and desire for leaving the field of work.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12A
• /
• pp.2000-2011
• /
• 2001

In this Paper, we convert conventional low speed(1x, 6x) DVD systems designed by analog PLL(Phase Locked Loop) into digital PLL to operate at high speed systems flexibly, and present optimal DPLL model in high speed(20x) DVD systems. Especially, we focused on the design of DPLL that can overcome channel effects such as bulk delay, sampling clock frequency offset and asymmetry phenomenon in high speed DVD systems. First, the modified Early-Late timing error detector as digital timing recovery scheme is proposed. And the four-sampled compensation algorithm using zero crossing point as asymmetry compensator is designed to achieve high speed operation and strong reliability. We show that the proposed timing recovery algorithm provides enhanced performances in jitter valiance and SNR margin by 4 times and 3dB respectively. Also, the new four-sampled zero crossing asymmetry compensation algorithm provides 34% improvement of jitter performance, 50% reduction of compensation time and 2.0dB gain of SNR compared with other algorithms. Finally, the proposed systems combined with asymmetry compensator and DPLL are shown to provide improved performance of about 0.4dB, 2dB over the existing schemes by BER evaluation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.3
• /
• pp.246-251
• /
• 2014

In case of prosthesis fabrication by CAD/CAM, location, area and contour of occlusal contacts can be adjusted so more functional occlusion can be acquired. Also, errors in a manufacturing process is reduced compared to cast metal prostheses and porcelain fused metal prostheses fabricated by conventional methods such as casting and porcelain build up. Therefore, prostheses by CAD/CAM show superior occlusion accuracy. Recently, virtual articulator function has been introduced to CAD/CAM system, which reproduces mandibular movement against maxilla. Thus, it is possible to consider occlusal interference in anterior/lateral movement as well as closing movement. There have been many studies on the marginal and internal fit of prostheses using zirconia but the occlusal fit of zirconia crown fabricated by CAD/CAM has not been researched as much. In this case report, 7 zirconia crowns were designed and fabricated by CAD/CAM for total 5 patients. The models of zirconia crowns before and after occlusal adjustment during intraoral try-in were scanned for occlusal contacts, which were compared to evaluate accuracy of prostheses and understand patterns of occlusal adjustment. Most of the occlusal adjustments were done on functional cusps and slopes of zirconia crown, and the magnitude of occlusal adjustment ranged from $15{\mu}m$ to $60{\mu}m$. In the zirconia crown fabricated with CAD/CAM systems, the occlusal adjustment is a necessary procedure, so additional procedures will be needed for compensating reduced mechanical properties.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.964-973
• /
• 1998

In this paper we propose a levitation and imbalance compensation controller design methodology of magnetic bearing system. In order to achieve levitation and elimination of unbalance vibartion in some operation speed we use the discrete-time Q-parameterization control. When rotor speed p = 0 there are no rotor unbalance, with frequency equals to the rotational speed. So in order to make levitatiom we choose the Q-parameterization controller free parameter Q such that the controller has poles on the unit circle at z = 1. However, when rotor speed p $\neq$ 0 there exist sinusoidal disturbance forces, with frequency equals to the rotational speed. So in order to achieve asymptotic rejection of these disturbance forces, the Q-parameterization controller free parameter Q is chosen such that the controller has poles on the unit circle at z = $exp^{ipTs}$ for a certain speed of rotation p ( $T_s$ is the sampling period). First, we introduce the experimental setup employed in this research. Second, we give a mathematical model for the magnetic bearing in difference equation form. Third, we explain the proposed discrete-time Q-parameterization controller design methodology. The controller free parameter Q is assumed to be a proper stable transfer function. Fourth, we show that the controller free parameter which satisfies the design objectives can be obtained by simply solving a set of linear equations rather than solving a complicated optimization problem. Finally, several simulation and experimental results are obtained to evaluate the proposed controller. The results obtained show the effectiveness of the proposed controller in eliminating the unbalance vibrations at the design speed of rotation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.11
• /
• pp.1043-1049
• /
• 2007

Data transfer rate and storage capacity are main criteria of the performance of the optical disk drive. The highest data transfer rate and the largest storage capacity is most desirable. To increase these performances, the actuator of the optical disk drive should have a high servo bandwidth to compensate the vibration of an optical disk. The servo bandwidth is limited by some flexible modes of the actuator, thus it is essential to increase the natural frequencies of the flexible modes. In this paper, we suggested a moving magnet type actuator having high frequencies of the flexible modes. Generally, the moving magnet type actuator has an advantage to increase the natural frequencies of the flexible modes because the moving magnet type actuator has simple structure and the Young's modulus of magnet is high. However, large moving mass and inefficiency of EM(electromagnetic) circuit cut down driving sensitivities of the actuator. To improve driving sensitivities, we designed the model with the closed electromagnetic circuit for tracking direction. In addition, driving sensitivities and the natural frequencies of the flexible modes were improved by using DOE(design of experiments) for electromagnetic circuit and modifying the lens holder.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.500-506
• /
• 1999

We designed and fabricated a bidirectional optical transceiver module for low cost access network. An integrated chip forming a pin-PD on an 1.3 urn FP-LD was assembled by flip-chip bonding on a Si optical bench, a single mode fiber with an angled end facet was aligned passively with the integrated chip on V-groove of Si-optical bench. Gaussian beam theory was applied to evaluate the coupling coefficients as a function of some parameters such as alignment distance, angle of fiber end facet, vertical alignment error. The theory is also used to search the bottle-neck between transmittance and receiving coupling efficiency in the bi-directional optical system. Tn this paper, we confirmed that reduction of coupling efficiency by the vertical alignment error between laser beam and fiber core axis can be compensated by controlling the fiber facet angle. In the fabrication of sub-module, a'||'&'||' we made such that the fiber facet have a corn shape with an angled facet only core part, the reflection of transmitted laser beam from the fiber facet could be minimized below -35 dE in alignment distance of 2: 30 /J.m. In the same condition, transmitted output power of -12.1 dEm and responsivity of 0.2. AIW were obtained.