• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제34권6호
• /
• pp.731-742
• /
• 2010

Modeling of rubber for design or analysis often requires confusing or complex work because there are a large number of constitutive models to be considered. Some models have few material constants, while others have many. Researchers have to prepare and fit extensive experimental data with caution and discretion. In this paper, we first compared some typical rubber models in which deformation was carried out by stretching up to around eight times the original size. We conclude that continuum-based models and chain molecular models can be used in the study of the small deformation in most engineering applications, but chain molecular models are preferred in the study of the large deformations in most biomaterial applications. As discrimination problems, Treloar's patch and cylindrical balloon stick are tested theoretically and numerically for studying bifurcation. In the case of Treloar's patch, by using the Kearsley's equation, we show that bifurcation exists for continuum-based models but not for chain molecular models. Both models show bifurcation in the cylindrical balloon stick. Therefore, in the analysis of the bifurcation of rubber showed that its existence also depends on the constitutive model selected.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.201-204
• /
• 2008

The proposed method, capable of predicting various stress-strain responses in axially loaded concrete confined with FRP (Fiber Reinforced Polymers) composites in a rational manner, is based on the fact that the volumetric expansion due to progressive microcracking in mechanically loaded concrete is an important measure of the extent of damage in the material microstructure. The elastic modulus expressed as a function of area strain and concrete porosity, the energy-balance equation relating the dilating concrete to the confining device interactively, the varying confining pressure, and an incremental calculation algorithm are included in the solution procedure. This procedure enables the evaluation of lateral strains consecutively according to the related mechanical model and the energy-balance equation, rather than using an empirically derived equation for Poisson's ratio or dilation rate as in other analytical methods.

• Journal of the Korea Concrete Institute
• /
• 제27권1호
• /
• pp.45-53
• /
• 2015

In general, RC columns are reinforced by spiral or tied steel and a strength of confined concrete is more increased than this of unconfined concrete. And strength and ductility of column are increased by a confinement effect. A confinement effect is affected by concrete strength, spacing, volume and strength of confinement steel. Many researchers suggested various confinement models which reflected these parameters by many experimental results. In this study, a load-strain relationship is evaluated by a confinement model in EC2, and it is compared with Mander model, Saatchioglu-Razvi model and Cusson et al. model. As results, it is appeared that a confinement model in EC2 is able to apply all kinds of concrete strength and a consistency in sectional analysis can be secured using material models in EC2. In parameter studies using material models in EC2, a confinement effect is more affected by a confinement steel than a concrete strength.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제24권1호
• /
• pp.97-106
• /
• 2011

In this study, viscoplastic material properties of solder alloy which is used in the electronics packages are inversely estimated. A specimen is fabricated to this end, and an experiment is conducted to examine deformation by Moir$\acute{e}$ interferometry. As a result of the experiment, bending displacement of the specimen and shear strain of the solder are obtained. A viscoplastic finite element analysis procedure is established, and the material parameters are determined to match closely with the experiments. The uncertainties which include inherent experimental error and insufficient data of experiments are addressed by using the method of computer model calibration. As a result, material parameters are identified in the form of confidence interval, and the displacements and strains using these parameters are predicted in the form the prediction interval.

• Journal of the Korean Society of Hazard Mitigation
• /
• 제10권6호
• /
• pp.35-43
• /
• 2010

This study was carried out to find reliable relations between various concrete strength properties which are used as input data in concrete pavement design program. Concretes were made from different sources of coarse grained(granite, limestone and sandstone) and fine grained aggregates such as natural sand, washed sand and crushed sand. From strength test results, model equations were obtained based on the relation between strengths. For each coarse grained aggregate, models for compression-flexural strengths, compression-split tensile strengths, compressive strength-modulus and flexural-split tensile strengths with age were obtained. For concrete mixed with gneiss granite aggregates, concrete strengths were obtained from numerical mean values of concrete strengths mixed with fine grained aggregates. In addition models for concrete split tensile strengths and modulus values were provide by averaging numerically the estimated values obtained from the derived relationship and the experimental values. This is due to more scattered values of split tensile strengths and modulus values than other strength properties. Finally criteria for drying shrinkage strain as well as Poisson's ratio for concrete used in pavement were presented for all mixes with differed coarse grained aggregates.

• Journal of the Korea Concrete Institute
• /
• 제27권3호
• /
• pp.311-317
• /
• 2015

Cement zero concrete produced by alkali-activators and industrial by-products such as slag instead of cement, enables to solve the environmental pollution problems provoked by the exhaustion of natural resources and energy as well as the discharge of carbon dioxide. However, researches on the cement zero concrete are still limited to material studies and thus, study on the structural behavior of relevant members is essential to use the cement zero concrete as structural materials. This paper aims to evaluate experimentally and analytically the flexural behavior of RC beams using 50 MPa alkali activated slag concrete. To achieve such a goal, flexural tests on three types of RC beam specimens were conducted. A nonlinear analysis model is proposed using the modulus of elasticity and stress-strain relationship of alkali activated slag concrete. The analysis results obtained by the proposed model agree well with the experimental results, which could verify the validity of the proposed model.

• Journal of the Korean Society of Food Science and Nutrition
• /
• 제38권7호
• /
• pp.935-945
• /
• 2009

This study was performed to find the optimum ratio of ingredients in the Chinese quince jam. The experiment was designed according to the D-optimal design of mixture design, which included 14 experimental points with 4 replicates for three independent variables (Chinese quince paste $45{\sim}60%$, pectin $1.5{\sim}4.5%$, sugar $45.5{\sim}63.5%$). A mathematical analytical tool was employed for the optimization of typical ingredients. The canonical form and trace plot showed the influence of each ingredient in the mixture against final product. By use of F-test, sweetness, pH, L, b, ${\Delta}E$, and firmness were expressed by a linear model, while the spreadmeter value, a, and sensory characteristics (appearance, color, smell, taste, and overall acceptability) were by a quadratic model. The optimum formulations by numerical and graphical method were similar: Chinese quince paste 54.48%, pectin 2.45%, and sugar 53.07%. Optimum ingredient formulation is expected to improve use of Chinese quince and contribute to commercialization of high quality Chinese quince jam.

• Composites Research
• /
• 제16권3호
• /
• pp.1-8
• /
• 2003

Densification occurs by the inelastic flow of the matrix materials during the consolidation processes at high temperature for MMCs, and the results depend on many process conditions such as applied pressure, temperature and volume fraction of fiber and matrix materials. This is particularly important in titanium matrix composites since material failure may occur by either the applied conditions or microstructural parameters through the processes, and thus a generic model based on micro-mechanical approaches enabling the evolution of density over time to be predicted has been developed. The mode developed is then implemented into FEM so that practical process simulation has been carried out. Further the experimental investigation of the consolidation behavior of SiC/Ti-6Al-4V composites using vacuum hot pressing has been performed, and the results obtained are compared with the model predictions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제39권2호
• /
• pp.129-135
• /
• 2015

In this experimental study, the thermal stability values of micrometer-sized silica particle-reinforced epoxy composite specimens were evaluated by measuring their thermal expansion coefficients and Young's moduli. For all specimens used in this study (from the baseline specimen to that containing 70 wt% silica filler), the thermal expansion coefficients and Young's moduli were gradually reduced down to 25% and increased up to 51%, respectively. The results of the experiment were compared with those of certain empirical models. The experimental results of the measurement of thermal expansion coefficients corresponded well with those of Kerner's model, which considers the bulk and shear moduli of the matrix and silica filler. However, the results of the measurement of Young's moduli using the empirical Mori-Tanaka model were observed to match better with those of the experiment. The comparison of the results of the experiment with those of the empirical models demonstrated that a reliable model for measuring the thermal expansion coefficients and Young's moduli of composite specimens needs to consider certain property variations in the composites in addition to volume fraction changes in the filler and matrix.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제23권4호
• /
• pp.409-415
• /
• 2010

A finite element model for punching shear of flat plate structures is presented. A parametric study also has been conducted to verification of influence of several parameters in terms of the flexural reinforcement ratio, slab thickness. Reisnner-Mindlin assumptions are adopted to consider of shear deformation. Layered shell element is considered for the material non-linearities. The finite element model of this study was verified comparing with existing experimental results. The model is able to predict the capacity of the flat plate structures. The punching shear of flat plate structures varied depending on the flexural reinforcement ratio, slab thickness.