• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.118-127
• /
• 2006

The wireless transmission medium inherently broadcasts a signal to all neighbor nodes in the transmission range. Existing asynchronous MAC protocols do not provide a concrete solution for reliable broadcast in link layer. This mainly comes from that an omnidirectional broadcasting causes to reduce the network performance due to the explosive collisions and contentions. This paper proposes a directional broadcast protocol by using neighborhood information in the link layer based o,1 directional antennas, named MNDB (MAC protocol with Neighborhood for reliable Directional Broadcast). This protocol makes use of neighborhood information and DMACA (Directional Multiple Access and Collision Avoidance) scheme through 4-way handshake to support a reliable directional broadcast. To analyze its performance, MNDB protocol si compared with $RMDB^{[1]}$, the protocol 2 of reference [3], and IEEE 802.11 $protocol^{[9]}$, in terms of the number of collisions, the number of dropped packets, the number of redundant packets, and broadcast delay.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.613-619
• /
• 2017

In this paper, DF(Dual Fuel) Generator modeling, which uses both conventional diesel fuel and LNG fuel, has been performed and monitoring system has been developed based on MATLAB/SIMULINK for the development of PMS(Power Management System) HILS(Hardware In the Loop Simulation). The principal components modeling of DF Generator are DF engine which provides the mechanical power and synchronous generator which convert the mechanical power into electrical power. Submodels, such as throttle body, intake manifold, torque generation and mass of LNG and diesel Quantity are used to perform DF engine. Also, governor is used for load sharing between paralleled DF generators to share a total load that exceeds the capacity of a single generator. To verify modeling of DF Generator designated ship lumped load Simulation is carried out. A validity of DF Generator has been verified by comparison between simulation results and estimated result from the designated lumped load.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.12
• /
• pp.2261-2269
• /
• 2017

The current LTE network system provides service by locally allocating eNodeB to the EPC(Evolved Packet Core). However, it is not suitable for inter-node communication based on the distributed network environment. In this paper, we propose an integrated system by configuring E-UTRAN and EPC as All-In-One type to enable service in each distributed node. M2M UE is mounted on a each node for wireless In-band backhaul link. The integrated node provides inter-node communication over the wireless in-band backhaul link. If a normal UE moves and an access node changes in the system all entities of LTE integrated into one, it is necessary to change the P-GW which is IP anchor. In order to support the inter-node mobility even if P-GW is changed, We defined UPFE(User Packet Forwarding Extension) scheme and implemented the handover procedure of EPC. Also, we analyze the cell range of the integrated LTE system with the addition of the node and compare the handover delay with the current system.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.47 no.4
• /
• pp.71-81
• /
• 2010

In grid system, Task scheduling based on list scheduling models has showed low complexity and high efficiency in fully connected processor set environment. However, earlier schemes did not consider sufficiently the communication cost among tasks and the composition process of lightpath for communication in optical gird environment. In this thesis, we propose LSOG (Leveling Selection in Optical Grid) which sets task priority after forming a hierarchical directed acyclic graph (DAG) that is optimized in optical grid environment. To determine priorities of task assignment in the same level, proposed algorithm executes the task with biggest communication cost between itself and its predecessor. Then, it considers the shortest route for communication between tasks. This process improves communication cost in scheduling process through optimizing link resource usage in optical grid environment. We compared LSOG algorithm with conventional ELSA (Extended List Scheduling Algorithm) and SCP (Scheduled Critical Path) algorithm. We could see the enhancement in overall scheduling performance through increment in CCR value and smoothing network environment.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.3
• /
• pp.41-49
• /
• 2011

In this paper, we propose an open protocol to be employed between a smart meter concentrator and a metering data collection server, and also evaluate its performance. Legacy concentrators performs the connection establishment and data gathering operations with DLMS/COSEM protocol standards. However, we note that there are no standardized protocols between the concentrator and the collection server, which inevitably conduces each commercial smart metering system to have its own proprietary protocol. In order to solve this problem, we propose an open protocol - Smart Meter Concentrator Control Protocol(SMCCP) by extending the existing standard protocol(DLMS/COSEM). The SMCCP can provide the proxy mode to enable efficient transmission between the concentrator and the data collection server. It also can support the relay mode to enable a direct communication between the data collection server and each far end smart meter. We also implement an emulator system and a protocol analyzer to provide its operation. In addition, we evaluate the session holding time and the link usage ratio in both relay and proxy modes with OMNET++ simulator.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.76-84
• /
• 2013

In the passive emitter localization using instantaneous TDOA (time difference of arrival) and FDOA (frequency difference of arrival) measurements, the estimation accuracy can be improved by collecting additional measurements. To achieve this goal, it is required to increase the number of the sensors. However, in electronic warfare environment, a large number of sensors cause the loss of military strength due to high probability of intercept. Also, the additional processes should be considered such as the data link and the clock synchronization between the sensors. Hence, in this paper, the passive localization of a stationary emitter is presented by using the successive TDOA and FDOA measurements from two moving sensors. In this case, since an independent pair of sensors is added in the data set at every instant of measurement, each pair of sensors does not share the common reference sensor. Therefore, the QCLS (quadratic correction least squares) methods cannot be applied, in which all pairs of sensor should include the common reference sensor. For this reason, a Gauss-Newton algorithm is adopted to solve the non-linear least square problem. In addition, to show the performance of the proposed method, we compare the RMSE (root mean square error) of the estimates with CRLB (Cramer-Rao lower bound) and derived the CEP (circular error probable) planes to analyze the expected estimation performance on the 2-dimensional space.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.4
• /
• pp.54-62
• /
• 2018

As a part of realization of artificial intelligence signal(AI Signal), this study proposed an actuated signal algorithm based on vehicle queue length that estimates in real time by deep learning. In order to implement the algorithm, we built an API(COM Interface) to control the micro traffic simulator Vissim in the tensorflow that implements the deep learning model. In Vissim, when the link travel time and the traffic volume collected by signal cycle are transferred to the tensorflow, the vehicle queue length is estimated by the deep learning model. The signal time is calculated based on the vehicle queue length, and the simulation is performed by adjusting the signaling inside Vissim. The algorithm developed in this study is analyzed that the vehicle delay is reduced by about 5% compared to the current TOD mode. It is applied to only one intersection in the network and its effect is limited. Future study is proposed to expand the space such as corridor control or network control using this algorithm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.348-356
• /
• 2014

The existing effective path-length model of ITU-R has some drawbacks: The prediction error is quite large compared to domestic measurement data and it is an empirical model in which the physical characteristics of rain cells are not considered. In this paper, a theoretical model for effective path-length using the rain-cell concept was proposed and its validity was verified using the measurement data. To analyze the statistical characteristics of rain cell parameters, the weather-radar data(CAPPI) measured by Korea Meterological Administration were analyzed and the correction factor was properly introduced to fit the Chollian beacon measurement data of ETRI(Electronics and Telecommunications Research Institute). To verify the proposed effective path-length model, it was compared with the Mugunghwa No. 5 beacon data measured in Chungnam National University with the support of ADD(Agency for Defense Development). It was confirmed that the prediction results of the proposed model are in good agreement with the measurement data.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.68-73
• /
• 2009

This paper describes design and implementation of a spread spectrum clock generator (SSCG) for the DisplayPort. The proposed architecture generates the spread spectrum clock using a sigma-delta fractional-N PLL. The SSCG uses a digital End order MASH 1-1 sigma-delta modulator and a 9bit Up/Dn counter. By using MASH 1-1 sigma-delta modulator, complexity of circuit and chip area can be reduced. The advantage of sigma-delta modulator is the better control over modulation frequency and spread ratio. The SSCG generates dual clock rates which are 270MHz and 162MHz with 0.25% down-spreading and triangular waveform frequency modulation of 33kHz. The peak power reduction is 11.1dBm at 270MHz. The circuit has been designed and fabricated using in 0.18$\mu$m CMOS technology. The chip occupies 0.620mm$\times$0.780mm. The measurement results show that the fabricated chip satisfies the DispalyPort standard.

• Proceedings of the Korea Inteligent Information System Society Conference
• /
• 2006.06a
• /
• pp.183-192
• /
• 2006

간세포암은 우리나라에서 전체 암사망자 중 17.2%로 3번째의 흔한 사망원인이며, 간암에 의한 사망률은 인구 10만 명당 약 21명에 이른다. 본 논문에서는 간 내부에서 발생하는 간세포암을 CT 영상에서 자동으로 추출하는 방법을 제안하여 간세포암의 보조진단으로서의 유용성에 대해 알아보고자 한다. 간 내부의 종양을 추출하기 위해 흉부의 윗부분에서 시작하여 2.5mm의 간격으로 약 45-50장 정도를 촬영한 CT 영상들을 대상으로 먼저 간 영역을 추출한다. 간 영역 추출은 먼저 관심이 없는 외부 영역을 갈비뼈를 중심으로 제거한 후 영상의 밝기 정보를 이용하여 각 기관의 영역을 분할 한다. 분할된 영역들은 위 아래로 인접한 영상에서의 분할 영역들과 밝기 값을 비교하여 적절하게 병합하는 3차원적 접근방법을 사용한다. 간 영역은 여러개의 영역들 중에서 간 영역의 구조 및 위치 등의 정보를 활용하여 추출한다. 추출된 간 영역에서 종양 판별과 추출을 위해 종양이 가지는 특징을 분석하여 종양을 추출한다. 전형적인 간세포암은 과혈관성 종양이므로 조영증강 CT 영상에서 주위보다 밝은 색으로 나타나며, 팽창 형성장을 보일 경우에는 구형으로 나타나는 특징이 있다. 이에, 주위 보다 밝은 색을 가지고 둥근형태를 가지는 영역을 종양의 후보영역으로 선정한 후, 그 영상의 위와 아래로 연결되는 영상에서도 같은 위치에서 같은 특징을 보이는 영역이 있으면 간 내부의 종양으로 판별하여 추출한다. 제안된 간 영역 및 간 종양 추출 방법의 정확성을 판별하기 위하여 CT 영상을 대상으로 실험하여 영상의학 전문의가 판단한 결과와 비교하였다. 간 영역 추출은 정확히 모두 추출되었으며, 간 종양 추출 및 판별은 전문의의 보조 진단도구로 활용할 수 있는 가능성이 매우 높다는 것을 확인할 수 있었다.emantic Similarity Measure 등을 단계적으로 수행하여 자동화되고 정확한 규칙식별을 하고자 한다. 이러한 방법들의 조합으로 인하여 규칙구성요소 추출이 되지 않을 후보 단어들의 수를 줄여서 보다 더 정확하고, 지능적인 규칙구성요소 추출 방법론을 제시하고 구현하여 지식관리자의 규칙습득에 대한 부담을 줄여 주고자 한다. 도움을 받을 수 있게 되었다.을 거치도록 되어있다. 교통주제도는 국가의 교통정책결정과 관련분야의 기초자료로서 다양하게 활용되고 있으며, 특히 ITS 노드/링크 기본지도로 활용되는 등 교통 분야의 중요한 지리정보로서 구축되고 있다..20{\pm}0.37L$, 72시간에 $1.33{\pm}0.33L$로 유의한 차이를 보였으므로(F=6.153, P=0.004), 술 후 폐환기능 회복에 효과가 있다. 4) 실험군과 대조군의 수술 후 노력성 폐활량은 수술 후 72시간에서 실험군이 $1.90{\pm}0.61L$, 대조군이 $1.51{\pm}0.38L$로 유의한 차이를 보였다(t=2.620, P=0.013). 5) 실험군과 대조군의 수술 후 일초 노력성 호기량은 수술 후 24시간에서 $1.33{\pm}0.56L,\;1.00{\ge}0.28L$로 유의한 차이를 보였고(t=2.530, P=0.017), 술 후 72시간에서 $1.72{\pm}0.65L,\;1.33{\pm}0.3L$로 유의한 차이를 보였다(t=2.540, P=0.016). 6) 대상자의 술 후 폐환기능에 영향을 미치는 요인은 성별로 나타났다. 이에 따른 폐환기능의 차이를 보면, 실험군의 술 후 노력성 폐활량이 48시간에 남자($1.78{\pm}0.61L$)가 여자(