• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.122-130
• /
• 2013

This work proposes a 12b 100MS/s 45nm CMOS four-step pipeline ADC for high-speed digital communication systems requiring high resolution, low power, and small size. The input SHA employs a gate-bootstrapping circuit to sample wide-band input signals with an accuracy of 12 bits or more. The input SHA and MDACs adopt two-stage op-amps with a gain-boosting technique to achieve the required DC gain and high signal swing range. In addition, cascode and Miller frequency-compensation techniques are selectively used for wide bandwidth and stable signal settling. The cascode current mirror minimizes current mismatch by channel length modulation and supply variation. The finger width of current mirrors and amplifiers is laid out in the same size to reduce device mismatch. The proposed supply- and temperature-insensitive current and voltage references are implemented on chip with optional off-chip reference voltages for various system applications. The prototype ADC in a 45nm CMOS demonstrates the measured DNL and INL within 0.88LSB and 1.46LSB, respectively. The ADC shows a maximum SNDR of 61.0dB and a maximum SFDR of 74.9dB at 100MS/s, respectively. The ADC with an active die area of $0.43mm^2$ consumes 29.8mW at 100MS/s and a 1.1V supply.

• Journal of the Korean Society of Radiology
• /
• v.5 no.5
• /
• pp.283-287
• /
• 2011

In this study, fine $Gd_2O_2S$:Tb powder was synthesized by using a low temperature solution-combustion method for a high-resolution digital x-ray imaging detector. From the fabricated phosphor power, the fine scintillator films was fabricated by particle sedimentation method and was investigated the luminescent property. From the experimental results of relative light output as a function of terbium concentration, the highest luminescent efficiency has at 5 wt% Tb concentration, and luminescent intensity decreased rapidly according to quenching effect about higher Tb concentration. Also, the relative light output of $270{\mu}m$-$Gd_2O_2S$:Tb film has 2945 pC/$cm^2$/mR. And light intensity was saturated at higher film thickness. Finally, to evaluate an image acquisition performance of fabricated phosphor, images were obtained by using commercial CMOS sensor and measured the MTF, NPS, and DQE. DQE(0 lp/mm) of fine phosphor film has 37%. But, DQE improvement of fine phosphor film is possible by resolving problem of film fabrication process and has a significant potential in the application of digital radiation imaging system later.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.1
• /
• pp.47-55
• /
• 2005

This work describes an 8b 240 MS/s CMOS ADC as one of embedded core cells for high-performance displays requiring low power and small size at high speed. The proposed ADC uses externally connected pins only for analog inputs, digital outputs, and supplies. The ADC employs (1) a two-step pipelined architecture to optimize power and chip size at the target sampling frequency of 240 MHz, (2) advanced bootstrapping techniques to achieve high signal bandwidth in the input SHA, and (3) RC filter-based on-chip I/V references to improve noise performance with a power-off function added for portable applications. The prototype ADC is implemented in a 0.18 um CMOS and simultaneously integrated in a DVD system with dual-mode inputs. The measured DNL and INL are within 0.49 LSB and 0.69 LSB, respectively. The prototype ADC shows the SFDR of 53 dB for a 10 MHz input sinewave at 240 MS/s while maintaining the SNDR exceeding 38 dB and the SFDR exceeding 50 dB for input frequencies up to the Nyquist frequency at 240 MS/s. The ADC consumes, 104 mW at 240 MS/s and the active die area is 1.36 ㎟.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.47-54
• /
• 2006

This work proposes a dual-channel 6b 1GS/s ADC for ultra wide-band communication system applications. The proposed ADC based on a 6b interpolated flash architecture employs wide-band open-loop track-and-hold amplifiers, comparators with a wide-range differential difference pre-amplifier, latches with reduced kickback noise, on-chip CMOS references, and digital bubble-code correction circuits to optimize power, chip area, and accuracy at 1GS/s. The ADC implemented in a 0.18um 1P6M CMOS technology shows a signal-to-noise-and-distortion ratio of 30dB and a spurious-free dynamic range of 39dB at 1GS/s. The measured differential and integral non-linearities of the prototype ADC are within 1.0LSB and 1.3LSB, respectively. The dual-channel ADC has an active area of $4.0mm^2$ and consumes 594mW at 1GS/s and 1.8V.

• Proceedings of the Korea Contents Association Conference
• /
• 2006.11a
• /
• pp.218-222
• /
• 2006

In making 3D animation with digital technology, it is necessary to increase productivity and reusability by managing production pipeline systematically through standardization of animation content. For this purpose, we try to develop the animation content management system that can manage all kind of information on the production pipeline, based on SCORM of e-teaming by considering production, publication and re-editing. A scene as the unit of visual semantics is standardize into an object that contains meta-data of place, cast, weather, season, time and viewpoint about the scene. The meta-data of content includes a lot of information of copyright, publication, description, etc, so that it plays an important role on the management and the publication. If an effective management system of meta-data such as ontology will be implemented, it is possible to search multimedia contents powerfully. Hence, it will bring on production and publication of UCC. Using the meta-data of content object, user and producer can easily search and reuse the contents. Hence, they can choose the contents object according to their preference and reproduce their own creative animation by reorganizing and packaging the selected objects.

• Journal of the Korean Institute of Gas
• /
• v.14 no.5
• /
• pp.13-18
• /
• 2010

This paper presents the development of an integrated control and safety management system for 9% nickel steel LNG storage tank. The new system added the measuring equipment of pressure, displacement and force compared to the conventional measurement and control system. The measured data has simultaneously been processed by integrating and analyzing with new control equipments and safety management systems. The integrated control and safety management system, which may increase a safety and efficiency of a super-large full containment LNG storage tank, added additional pressure gauges and new displacement/force sensors at the outer side wall and a welding zone of a stiffener and top girder of an inner tank, and the inner side wall of a corner protection tank. The displacement and force sensors may provide failure clues of 9% nickel steel structures such as an inner tank and a corner protection, and a LNG leakage from the inner tank. The conventional leak sensor may not provide proper information on 9% nickel steel tank fracture even though LNG is leaked until the leak detector, which is placed at the insulation area between an inner tank and a corner protection tank, sends a warning signal. Thus, the new integrated control and safety management system is to collect and analyze the temperature, pressure, displacement, force, and LNG density, which are related to the tank system safety and leakage control from the inner tank. The digital data are also measured from control systems such as displacement and force of 9% nickel steel tank safety, LNG level and density, cool-down process, leakage, and pressure controls.

• Journal of the Korean Institute of Gas
• /
• v.14 no.2
• /
• pp.40-46
• /
• 2010

In this study, the integrated control and safety management system for a super-large LNG membrane storage tank has been presented based on the investigation and analysis of measuring equipments and safety analysis system for a conventional LNG membrane storage tank. The integrated control and safety management system, which may increase a safety and efficiency of a super-large LNG membrane storage tank, added additional pressure gauges and new displacement/force sensors at the steel anchor between an inner tank and a prestressed concrete structure. The displacement and force sensors may provide clues of a membrane panel failure and a LNG leakage from the inner tank. The conventional leak sensor may not provide proper information on the membrane panel fracture even though LNG is leaked until the leak detector, which is placed at the insulation area behind an inner tank, send a warning signal. Thus, the new integrated control and safety management system is to collect and analyze the temperature, pressure, displacement, force and LNG density, which are related to the tank system safety and leakage control from the inner tank. The digital data are also measured from measurement systems such as displacement and force of a membrane panel safety, LNG level and density, cool-down process, leakage, and pressure controls.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.699-707
• /
• 2016

This paper proposes a low-complexity central processing unit (CPU) that is suitable for deeply embedded systems, including Internet of things (IoT) applications. The core features a 16-bit instruction set architecture (ISA) that leads to high code density, as well as a multicycle architecture with a counter-based control unit and adder sharing that lead to a small hardware area. A co-processor, instruction cache, AMBA bus, internal SRAM, external memory, on-chip debugger (OCD), and peripheral I/Os are placed around the core to make a system-on-a-chip (SoC) platform. This platform is based on a modified Harvard architecture to facilitate memory access by reducing the number of access clock cycles. The SoC platform and CPU were simulated and verified at the C and the assembly levels, and FPGA prototyping with integrated logic analysis was carried out. The CPU was synthesized at the ASIC front-end gate netlist level using a $0.18{\mu}m$ digital CMOS technology with 1.8V supply, resulting in a gate count of merely 7700 at a 50MHz clock speed. The SoC platform was embedded in an FPGA on a miniature board and applied to deeply embedded IoT applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.476-477
• /
• 2013

반도체의 성능은 최근 10년 사이에 급격하게 발전했고 아날로그 및 디지털 회로 소자들에 있어 저전력/고속 특성 요구가 커지고 있다 [1]. 상온에서 30,000 $cm^2$/Vs 이상의 전자 이동도를 가지며 큰 conduction band offset을 갖는 InAs/AlSb 2차원전자가스(2DEG) 소자는 Spinorbit-interaction의 값이 매우 커서 SPIN-FET 소자로 크게 주목받고 있다 [2]. 본 발표자들은 GaAs 기판위에 성장한 InAs 2DEG HEMT 소자의 전/자기적인 특성과 고속반응 물질로 주목 받는 InSb 박막소자의 doping 특성에 따른 전기적/물리적인 특성의 평가에 대해 그 결과를 소개하고자 한다. 격자정합과 Semi-insulating 기판의 부재로 상용화되어 있는 GaAs와 InP 기판위에 물질차이에 따른 고유의 한계 특성을 줄이기 위한 Pseudomorphic이라 불리는 특별한 박막 성장 기법을 적용하여 높은 전자 이동도를 가지며 spin length가 길어 Spin-FET로서 크게 주목받고 있는 InAs 2DEG HEMT 소자를 완성시켰다. 60,000 ($cm^2$/Vs) 이상의 높은 전자 이동도를 갖는 소자의 구현을 목표로 연구를 진행하였으며 1.8 K에서 측정된 Spin-orbit interaction의 값은 6.3e-12 (eVm)이다. InAs/InGaAs/InAlAs 및 InGaAs/InAlAs 구조의 InP 기반의 소자에서 보다 큰 값으로 향후 Spin-FET 응용에 크게 기대하고 있다. 또한, GaAs 기판위에 구현된 InSb 소자는 격자부정합 감소를 위해 InAs 양자점을 사용하여 약 $2.6{\mu}m$ 두께로 구현된 InSb 박막 소자는 상온에서 약 60,400 ($cm^2$/Vs)의 상온 전자이동도를 보였으며 현재 동일 두께에서 세계 최고결과(~50,000 $cm^2$/Vs)에 비해 월등하게 높은 값을 보이고 있다. Hall bar pattern 공정을 거쳐 완성된 소자는 측정 결과 10~20% 이상 향상된 전자 이동도를 보였다. 2e18/$cm^3$ 미만의 p-doping의 경우, 상온에서 n-type 특성을 보이나, 저온에서 p-type으로 변하는 특성을 보였고 n-doping의 경우 5e17/$cm^3$까지는 전자 이동도만 감소하고, doping에 의한 효과는 크게 없었다. 1e18/$cm^3$의 높은 doping을 할 경우 carrier가 증가하는 것을 확인했다. 이상의 측정 결과로 Spin-FET 소자로서 아주 우수하다는 것을 확인할 수 있었고 n-/p- type이 특성을 고려한 high quality InSb 박막소자의 응용을 위한 중요한 정보를 얻을 수 있었다.

• Archives of design research
• /
• v.18 no.2 s.60
• /
• pp.303-314
• /
• 2005

This study is intended to promote local woodcraft industry with revitalization of local festival in Inje-county. To do so, we propose the travel souvenir design with local identity and the plan for production and marketing based on the management of 'Design Hospital' and the building of production method through 'laser wood inlaying technique like puzzle style'. Research method is benchmarking analysis of successful cases of travel souvenir which is developed for cultural contents of local festival. The result of this study is the following. First, design outsourcing is done one of support in industry focused on old boy network, Through it, Special brain of design can be supplied without compensation. Also the difficulty of manpower problem is lessened and the ability of product development in short term can be guaranteed. On the basis of this, we are able to apply Mass Customization production by up to date digital production method. This enables us to maintain the production flexibility of cultural goods fit for the traits of local festival. This study is intended to present the best model guananteeing both profit of wood technological industry and the possibility of local cultural.