• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.496-503
• /
• 2010

The implementation of a RF transceiver for WRAN(Wireless Regional Area Network) system based on IEEE 802.22 standard using Cognitive Radio technology is presented in this paper. A CMOS RF transceiver IC for WRAN system operates in VHF/UHF(54~862MHz) broadband, and employs dual-path direct-conversion configuration and the in-band harmonic distortions are effectively suppressed by exploiting the dual-path direct conversion architecture. For 64QAM(3/4 coding rate) OFDM signal, an EVM of <-31.4dB(2.7%) has been achieved at 10dBm off-chip PA output power and the total chip area with pads is 12.95 mm2. The experimental results show that the proposed CMOS RF transceiver IC has perfect performance for WRAN system based on TDD(Time Division Duplex) mode.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.141-145
• /
• 2008

When the current flows to parallel lines with different length, it is researched that the radiation is occured by the common-mode current radiates, and the small light weight antenna composed of dual elements by using the principle is proposed. However, there is a problem in production about this antenna because this liner antenna is structured by combining with wires. In this paper, we improved this liner antenna, and designed the plane antenna composed of dual elements with different length in the plane printed board to produce and to design easily. Furthermore, the antenna with the wide-band characteristic is also designed in the same board. The radiation pattern is similar to the dipole antenna on account of designing the triangular patch S, the notch and two tapers in patch S, the notch and two tapers in the antenna element. In result, it was able to design the antenna working wider band-width(the bandwidth ratio about 58%, $VSWR{\le}2$).

• Journal of the Institute of Convergence Signal Processing
• /
• v.15 no.2
• /
• pp.42-47
• /
• 2014

A finger-gesture game controller using the single camera is implemented in this paper, which is based on the recognition of the number of fingers and the index finger moving direction. Proposed method uses the CAMShift algorithm to trace the end-point of index finger effectively. The number of finger is recognized by using a double circle tracing method. Then, HSI color mode transformation is performed for the CAMShift algorithm, and YCbCr color model is used in the double circle tracing method. Also, all processing tasks are implemented by using the Intel OpenCV library and C++ language. In order to evaluate the performance of the proposed method, we developed a shooting game simulator and validated the proposed method. The proposed method showed the average recognition ratio of more than 90% for each of the game command-mode.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.10
• /
• pp.89-96
• /
• 2003

In this paper, a CCSDS(Consultative Committee for Space Data Systems) telecommand(TC) decryptor for the security of geostationary communications satellite was implemented. For the confidentiality of CCSDS TC datalink security, Option-A which implements the security services below the transfer sublayer was selected. Also CFB(Cipher Feedback) operation mode of DES(Data Encryption Standard) was used for the encryption of 56-bit data bits in 64-bit codeblock. To verify Decryptor function, the DES CFB logic implemented on A54SX32 FPGA(Field Programmable Gate Array) was integrated with interface and control logics in a PCB(Printed Circuit Board). Using a function test PC, the encrypted codeblocks were generated, transferred into the decryptor, decrypted, and the decrypted codeblocks were transmitted to the function test PC, and then compared with the source codeblocks. Through LED(Light Emitting Diode) ON operation by driving the relay related to Op-code decoded and the comparison between the codeblock output waveforms measured and those simulated, the telecommand decryptor function was verified.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.991-997
• /
• 2004

In this paper, we propose the architecture of modem receiver to fabricate HomePNA 2.0 chip. HomePNA suffers from inferior channel because of bridge tap, the effect of amateur HAM band and so on. To transfer data over such channel, HomePNA 2.0 uses training sequence to equalize channel and uses FD-QAM optionally as modulation method. So modem receiver demodulate QAM based signal and needs optimum architecture that fully uses these transmission feature. As a result of research, we define 2 mode function of modem receiver depending on TX/RX state. In this paper, particularly, we show the algorithm of equalizer, carrier phase recovery and frame synchromzationblock and propose architecture that improve the performance of channel equalization and is stable in operation. In the end, we estimate the performance of proposed HomePNA2.0 modem receiver over HomePNA TEST LOOP using SPW program.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.8C
• /
• pp.763-770
• /
• 2006

In this paper, a variable Reed-Solomon(RS) decoder with erasure decoding functionality is designed based on the modified Euclid's algorithm(MEA). The variability of the decoder is implemented through shortening and puncturing based on the RS(124, 108, 8) code, other than the primitive RS(255, 239, 8) code. This leads to shortening the decoding latency. The decoder performs 4-step pipelined operation, where each step is designed to be clocked by an independent clock. Thus by using a faster clock for the MEA block, the complexity and the decoding latency can be reduced. It can support both continuous- and burst-mode decoding. It has been designed in VHDL and synthesized in an FPGA chip, consuming 3,717 logic cells and 2,048-bit memories. The maximum decoding throughput is 33 MByte/sec.

• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.15-21
• /
• 2000

Optical fiber temperature sensor, using resonance wavelength shifting of single mode fiber-to-planar waveguide coupler by heat, was fabricated. Thermo-optic polymers, have large change of refractive index due to heat, were used for planar waveguide. The device fabrication procedure including fiber polishing steps was illustrated and the device structure with independent polarization was demonstrated experimentally. The resonance wavelength difference of fabricated device was less than 2nm. The resonance wavelength shifting owing to temperature variation, from room temperature($24^{\circ}C$) to $90^{\circ}C$, was showed $-0.54nm/^{\circ}C$, $-3nm/^{\circ}C$.

• Journal of KIISE:Information Networking
• /
• v.33 no.5
• /
• pp.355-368
• /
• 2006

This paper introduces a new split-TCP approach for improving TCP performance over IEEE 802.11-based wireless LANs. TCP over wireless LANs differently from wired networks is not aggressive, which is a fundamental reason for poor performance. Therefore, we propose TAS (TCP-Aware Sub-layer) to migigate this problem. Our scheme extends the split-connection approach that divides a connection into two different connections at a split point such as an access point (AP). Using TAS, a wireless node emulates TCP ACK packets using MAC ACK frames, instead of receiving real TCP ACK packets. We compared TAS with both normal TCP and I-TCP (Indirect TCP) by NS2 simulation. Results show that TAS achieves higher throughput, more fair resource allocation and, in power-saving mode, shorter delays.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.5
• /
• pp.27-35
• /
• 2000

This paper deals with a control strategy for constant output power of SSRT(Soft Switching Resonant Type) FB(Full Bridge) DC-DC converter by an improved phase shift controller. When the FB DC-DC converter for the high density and the high effect control is operated in high speed switching, the switching loss and switching stress of the switching devices are increased. So, the soft switching method, which has the phase shift control with the digital I-PD controller, must be use in order to reduce its. And the output voltage that controlled by the digital I-PD controller tracks a reference without steady state error in variable input voltage. The validity of control strategy that proposed is verified from simulation results and experimental results by the DSP(TMS320C32).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.3
• /
• pp.338-346
• /
• 2016

Wearable Device has various constraint about battery power consumption, size, weight, etc, because the devices is worn and operated by person and provide services. So, if a device includes too many functions, it dose not satisfies the constraint and lose price competitiveness due to become expensive. Therefore we suggest that make reassembly Unit Modular Device witch has common used functions in wearable devices and user can receive various services to reassemble Unit Modules. It is comprised of frames and modules. Each module has various functions. Each frames help module to communicate each modules. To realize this device, we design to guarantee each services to use necessary modules, to give priority to modules depending on the important of the task, to set that does not use to low energy mode.