• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.4
• /
• pp.111-116
• /
• 2000

경간사이에 creep-coupler가 설치된 경부 고속철도 교량에 TGV-K 열차의 제동에 의한 교량의 종방향 동적거동을 해석하였다. 교량은 40m 길이의 2경간 연속교이며, 종방향 충격 하중을 인접 경간 혹은 교대로 전달하기 위한 목적으로 인접하고 있는 두 교량 사이의 creep-coupler가 설치되었다. 철도교의 경우에는 레일에 대한 종방향 축력검토가 매우 중요하므로, 이를 지지하고 있는 교량의 하부구조(교각과 기초)의영 향을 고려한 교량의 동적거동해석이 요구된다. 본 연구에서는 TGV-K의 실제 제동하중에 의한 KHSR(Korea high speed railway)에 건설중인 실제교량의 동해석을 하부구조와 동특성치를 고려하여 수행하였다. TGV-K는 객차사이에 대차가 위치하므로 전체 열차의 모델링이 한꺼번에 이루어 져야한다. 동핵석을 위해서 열차의 3차원 수치모델링이 이루어졌다. TGV-K의 제동은 동력차의 전기적인 제동에 의한 회생제동력(regenerative braking force)과 객착의 기계적인 판제동(disk braking)으로 이루어진다. 이러한 제동작용의 고려에 실제 TGV-K의 제동함수가 사용되었다.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.455-460
• /
• 2003

180km/h 급 한국형 틸팅차량의 틸팅 메카니즘 기구동역학 해석을 통하여 얻어진 틸팅 대차를 형성하는 주요 파라메터들의 값을 기반으로 틸팅대차용 엑츄에이터의 성능과 용량을 계산하여 설계에 결과를 반영하고자 한다. 승객의 안락감을 유지하기 위해 차체 틸팅 각가속도에 Sine 연속 함수를 적용하여 차체의 틸팅 제어 패턴을 결정하였으며, 이를 통해 차체의 틸팅 각속도와 틸팅각의 패턴을 얻어내었다. 또한 이번 연구를 통해 틸팅 메카니즘의 파라메타를 변화하면서 각각의 틸팅각에 따른 Swing bar 와 엑츄에이터에 작용되는 반발력에 대한 영향력을 분석, 검토하였으며, 이에 따른 엑츄에이터의 출력과 변위 속도등의 변화를 조사하였다. 이러한 결과와 틸팅 메카니즘 기구동력학 해석의 결과를 토대로 틸팅차량이 요구하는 최적의 틸팅 운동을 수행하는 파라메타를 결정하였다.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.229-230
• /
• 2014

본 논문은 고속전철용 1C1M 추진제어장치의 개발에 관한 것이다. KTX-산천 추진제어장치와 호환되도록 컨버터 부분은 DC링크를 공유하여 컨버터 2대를 병렬 운전하도록 하였다. 인버터 2대를 배치하여 견인전동기를 개별적으로 제어할 수 있도록 하였다. 동일 대차에서 1축, 2축 바퀴의 직경차는 1C2M 추진제어장치에서는 4mm 이하로 관리되고 있다. 1C1M 추진제어장치를 개발하여 바퀴의 직경차가 40mm 이하로 관리되도록 바퀴 직경관리 기준을 향상 시켜 바퀴의 사용 시간을 연장할 수 있도록 하였다. 컨버터, 인버터가 중고장에 의하여 차단 시 고장난 컨버터, 인버터 군을 차단하고 나머지 컨버터, 인버터 군은 재기동하는 충전회로 및 시퀀스를 추가하여 50% 동력을 사용하도록 하였다. 개발된 추진제어장치는 전력회로 시험, 기능 동작 시험을 통하여 제어가 원활히 수행됨을 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.11
• /
• pp.979-986
• /
• 2016

The tripod shafts of constant-velocity joint are used in both the trains KTX and KTX-sanchon. It is an important component that connects the motor reduction unit and the axle reduction unit in a power bogie. The tripod shaft not only transmits drive and brake torque in the rotational direction, but also slides in the axial direction. If the drive system is loaded with an excessive torque, the fuse part of the shaft will be fractured firstly to protect the other important components. In this study, a rig was developed for conducting torsion tests on the tripod shaft, which is a type of mechanical fuse. The tripod shafts were subjected to torsional fracture test and torsional fatigue test on the rig. The weak zone of the tripod shaft was identified, and its fatigue life was predicted using finite element analysis (FEA). After analyzing the FEA results, design solutions were proposed to improve the strength and fatigue life of the tripod shaft. Furthermore, the deterioration trend and time for failure of the tripod shaft were verified using the hysteresis loops which had been changed with the advancement of the torsional fatigue test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.797-803
• /
• 2019

This study was carried out to reduce the lateral vibration of high-speed electric multiple units. In the study, the high-speed electric multiple unit prototype (HEMU-430X) has a high lateral vibration at low equivalent conicity regardless of the wheel profiles (XP55, GV40, S1002). As wheel wear progresses and the equivalent conicity increases, the lateral vibration tends to decrease. The reason is that a combination of the suspension characteristics causes the body and bogie to resonate at a frequency of 1.4 Hz when the equivalent conicity is low, resulting in body hunting. An investigation of the lateral vibration of overseas high-speed trains showed that a decrease in the hydraulic stiffness of the yaw damper could improve the vibration. The series stiffness of the yaw damper is a combination of the hydraulic stiffness and elastic joint. In this study, an attempt was made to improve the lateral vibration by lowering the stiffness of the elastic joint. The series stiffness of the adjusted yaw damper was approximately 60% compared to the original one. The on track test results showed improvement in the lateral vibration for both running directions. The vibration reduction method of this study can be used for EMU-250 and EMU-320 in future commercial operations.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.797-803
• /
• 2010

A dynamic analysis procedure is developed to provide a better estimation of the dynamic responses of pre-stressed concrete (PSC) box girder bridges on the Korea high speed railway. Particularly, a three dimensional numerical model including the structural interaction between high speed vehicles, bridges and railway endures to analyze accurately and evaluate with in-depth parametric studies for dynamic responses of bridge due to the high speed railway vehicles. Three dimensional frame element is used to model the PSC box girder bridges, simply supported span lengths 40 m. The high-speed railway vehicles (K-TGV) including a locomotive are used as 38-degree of freedom system. Three displacements (vertical, lateral, and longitudinal) as well as three rotational components (pitching, rolling, and yawing) are considered in the 38-degree of freedom model. The dynamic analysis by Runge-Kutta method which are able to analyze considering the dynamic impact factors are compared and contrasted. It is proposed as an empirical formula that the impact factors damaged the bridge load-carrying capacities occurs to the bride due to high-speed vehicle.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8700-8706
• /
• 2015

The first driving device of the power bogies for the Korean high-speed railway vehicle consists of the traction motor (TM) and the motor reduction gears unit (MRU). Although TM and MRU are the mechanically integrated structures, their time between overhauls (TBO) have two separate intervals due to different technical requirements(i.e. TBO of MRU: $1.8{\times}10^6km$, TBO of TM: $2.5{\times}10^6km$). Therefore, to reduce the unnecessary number of preventive maintenances, it is important to evaluate the optimal TBO with a viewpoint of reliability-center maintenance towards cost-effective solution. In this study, derived from the field data in maintenance, fault tree analysis and failure rate of the subsystem considering criticality of the components are evaluated respectively. To minimize the conventional total maintenance cost, the same optimal TBO of the components is derived from genetic algorithm considering target reliability and improvement factor. In this algorithm, a chromosome which comprised of each individual is the minimum preventive maintenance interval. The fitness function of the individual in generation is acquired through the formulation using an inverse number of the total maintenance cost. Whereas the lowest common multiple method produces only a four percent reduction compared to what the existing method did, the optimal TBO of them using genetic algorithm is $2.25{\times}10^6$km, which is reduced to about 14% comparing the conventional method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.697-704
• /
• 2017

This study was carried out to investigate and alleviate the vibration problem of commercial high-speed trains. First, the measurement of the carbody vibration was performed, in order to determine the vibration level of the high-speed train. The measurement result showed that the vibration level of the driver cab was higher than that of the passenger car and that the vibration became bigger toward the trailing end of the train. The vertical vibration of the driver cab and passenger car was larger than the transverse vibration, and the maximum value of the vibration in the ballast section was larger than that in the concrete section. A dynamic analysis was carried out to improve the vibration of the KTX-Sancheon train. The results of the analysis showed that it is necessary to reduce the vibration of the driver cab and both ends of the passenger cars. To reduce the vibration of the driver cab, it was recommended that the stiffness of the secondary coil spring be reduced and the damping coefficient of the secondary vertical damper be increased. It was found that the failure of the suspension system could be the origin of the vibration problem of the high-speed train. The proper management of wheel wear plays an important role in the improvement of the operation efficiency and reduction of the carbody vibration of high-speed trains, and research is underway to change the present wheel profile to increase the mileage between wheel turning.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.8
• /
• pp.711-719
• /
• 2016

In this study, we derived an theoretical equation, using a simplified spring-mass model for the rolling stock, to obtain the overriding behavior of a leading vehicle, which is considered as the main factor in train accidents. To verify the derived equation, we created a simple 2D model based on the theoretical model, and a simple 3D model considering the characteristics of the power bogie. We then compared the theoretical results with the simulation results obtained using LS-DYNA. The maximum relative derivations in the vertical displacements at the first end-buffer, which is the most important point in overriding, were 3.5 [%] and 1.7 [%] between the two results. Further, we evaluated collision-induced overriding displacements using the theoretical equation for a rubber draft gear, a hydraulic buffer under various collision conditions. We have suggested a theoretical approach for the realization of overriding collision accidents or the energy absorption design of the front end of trains.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.493-501
• /
• 2016

In this study, core technologies of a traction system on a mountain tram operating on the track of mountain road full of sharp curves and steep gradients were developed. In domestic mountain resort areas, sometimes the transportation service is not provided in winter because of ice and heavy snow on roads, so a mountain railway service independent of the climate and geographic conditions is needed. A traction system was designed taking into account of the power of a traction motor to climb the gradient of 120 ‰, which is common in domestic mountainous areas. and power transmission system was designed to consider the installation space for the traction system. In addition, a reduction gear and a propeller shaft were developed. An elastic pinion was developed and applied to the rack & pinion bogie system for steep gradient so that noise and vibration generated by contact between the steel gears could be reduced. Impact comparison tests showed that the vibration level of the elastic pinion is one-third lower than that of previous steel pinion. Independent rotating wheels and axles were developed for the bogie system to operate on the sharp curve of a 10 meter radius. In addition, the band braking system was developed to enhance the braking force during running on the steep gradient. A test for the braking force showed it exerts the required braking force. The performance of the developed core components were verified by the tests and finally they were applied to the bogie system running on the track of steep gradient and sharp curve.