• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.10 s.352
• /
• pp.90-97
• /
• 2006

We report our research work on the millimeter-wave broadband amplifier integrating the shunt peaking technology with the cascode configuration. The millimeter-wave broadband cascode amplifier on MIMIC technology was designed and fabricated using $0.1{\mu}m\;{\Gamma}-gate$ GaAs PHEMT, CPW, and passive library. The fabricated PHEMT has shown a transconductance of 346.3 mS/mm, a current gain cut off frequency ($f_T$) of 113 GHz, and a maximum oscillation frequency ($f_{max}$) of 180 GHz. To prevent oscillation of designed cascode amplifier, a parallel resistor and capacitor were connected to drain of common-gate device. For expansion of the bandwidth and flatness of the gain, we inserted the short stub into bias circuits and the compensation transmission line between common-source device and common-gate device, and then their lengths were optimized. Also, the input and output stages were designed using the matching method to obtain the broadband characteristic. From the measurement, we could confirm to extend bandwidth and flat gain by integrating the shunt peaking technology with the cascode configuration. The cascode amplifier shows the broadband characteristic from 19 GHz to 53.5 GHz. Also, the average gain of this amplifier is about 6.5 dB over the bandwidth.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.11
• /
• pp.13-22
• /
• 2010

This paper proposed the dual-loops multiphase DLL based mixed VCO/VCDL for a high frequency phase noise suppression of the input clock and the multiple frequencies generation with a precise duty cycle. In the proposed architecture, the dual-loops DLL uses the dual input differential buffer based nMOS source-coupled pairs at the input stage of the mixed VCO/VCDL. This can easily convert the input and output phase transfer of the conventional DLL with bypass pass filter characteristic to the input and output phase transfer of PLL with low pass filter characteristic for the high frequency input phase noise suppression. Also, the proposed DLL can correct the duty-cycle error of multiple frequencies by using only the duty-cycle correction circuits and the phase tracking loop without additional correction controlled loop. At the simulation result with $0.18{\mu}m$ CMOS technology, the output phase noise of the proposed DLL is improved under -13dB for 1GHz input clock with 800MHz input phase noise. Also, at 1GHz operating frequency with 40%~60% duty-cycle error, the duty-cycle error of the multiple frequencies is corrected under $50{\pm}1%$ at 2GHz the input clock.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6B
• /
• pp.561-571
• /
• 2006

RFID technology, as one contact-less identification technology with using electronic tag, is the field where its multiple researches have been studied. Especially, in the field of supply chain management, when it is necessary to identify a lot of objects by real-time, performance of anti-collision algorithm for multiple tag identification has an effect on performance of entire system. GEN2 is global, open, interoperability protocol for UHF RFID system, the active researches and developments are processed about it. In this paper, we introduce an anti-collision algorithm based on Slotted-ALOHA for GEN2 protocol, focus on estimating number of tags and setting number of slots and review the previous works. We propose new scheme that can estimate number of tags efficiently, and define system efficiency newly when it's used in setting number of slots. We also present result of compare and analysis with previous scheme through simulation. The proposed scheme of estimating number of tags is easy to implement, number of tags which is less than 4 times of number of slots can estimate tags efficiently, we also proved that identification efficiency based on weighted-slot distinguished with definition of previous slot efficiency can improve system efficiency.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.83-89
• /
• 2006

This paper describes the design of I/Q channel 12bit Digital-to-Analog Converter(DAC) which shows the conversion rate of 120MHz and the power supply of 3.3V with 0.35um CMOS n-well 1-poly 4-metal process for advanced wireless transceiver. The proposed DAC utilizes 4-bit thermometer decoder with 3 stages for minimum glitch energy and linearity error. Also, using a optimized 4bit thermometer decoder for the decrement of the chip area. Integral nonlinearity(INL) of ${\pm}1.6LSB$ and differential nonlinearity(DNL) of ${\pm}1.3LSB$ have been measured. In single tone test, the ENOB of the proposed 12bit DAC is 10.5bit and SFDR of 73dB(@ Fs=120MHz, Fin=1MHz) is measured, respectively. Dual-tone test SFDR is 61 dB (@ Fs=100MHz, Fin=1.5MHz, 2MHz). Glitch energy of 31 pV.s is measured. The converter consumes a total of 105mW from 3.3-V power supply.

• Journal of Broadcast Engineering
• /
• v.16 no.5
• /
• pp.834-845
• /
• 2011

Massive broadcasting contents such as UHD(Ultra High Definition) TV which requires multi-channel capacity for transmission has been introduced in recent years. A transmission scheme with channel bonding has been considered for transmission of massive broadcasting contents. In HFC(Hybrid Fiber Coaxial) networks, DOCSIS 3.0(Data Over Cable Service Interface Specification 3.0) has already applied channel bonding schemes for up/downstream of data service. A method unlike DOCSIS 3.0 is required to introduce a channel bonding scheme in the broadcasting service having unidirectional transmission with a downstream. Since a massive broadcasting content requires several channels for transmission, VBR(Variable Bit Rate) transmission has been emerging for the bandwidth efficiency. In addition, research on channel allocation and resource scheduling is required to guarantee QoS(Quality of Service) for the broadcasting service based on VBR. In this paper, we propose a transmission method for mass broadcasting service in HFC network and show the UHD transmission simulator developed to evaluate the performance. In order to evaluate the performance, we define various scenarios. Using the simulator, we assess the possibility of channel bonding and VBR transmission for UHD broadcasting system to provide mass broadcasting service efficiently. The developed simulator is expected to contribute to the efficient transmission system development of mass broadcasting service.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.9
• /
• pp.12-20
• /
• 2001

The ATM-PON has an important meaning at next generation access network because the equipment transmits various types of user traffic with a single platform through the passive optical splitter. Ranging is a technology to place all ONUs at the same virtual distance in order to provide the synchronization for the upstream signal in the ATM-PON based on the Time Division Multiplexing (TDM). In this paper, we review the merits of ATM PON and related protocol for the PON operation. We summarize and analyze the steps about the ranging protocol based on ITU-T G.983.1 and implement a simulator that can simulate the ranging procedure based on our modeling. In this paper, we can investigate time requirements of G.983.1 by using the simulator and find out the wasted rate of the bandwidth during the ranging procedure in order to know the influence for ONUs while ATM-PON is in-service. Also, we show that a new ranging scheme reducing window size can avoid the degradation of quality of service of ONUs in service with simulation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.11
• /
• pp.63-70
• /
• 2001

We demonstrate the MMIC (monolithic microwave integrated circuit) frequency doublers generating stable and low-cost 29 GHz local oscillator signals from 14.5 GHz input signals. These devices were designed and fabricated by using the M MIC integration process of $0.1\;{\mu}m$ gate-length PHEMTs (pseudomorphic high electron mobility transistors) and passive components. The measurements showed S11 or -9.2 dB at 145 GHz, S22 of -18.6 dG at 29 GHz and a minimum conversion loss of 18.2 dB at 14.5 GHz with an input power or 6 dBm. Fundamental signal of 14.5 GHz were suppressed below 15.2 dBe compared to the second harmonic signal at the output port, and the isolation characteristics of fundamental signal between the input and the output port were maintained above :i0 dB in the frequency range 10.5 GHz to 18.5 GHz. The chip size of the fabricated MMIC frequency doubler is $1.5{\times}2.2\;mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.45 no.4
• /
• pp.50-58
• /
• 2008

In this paper, we propose a color transient improvement (CTI) algorithm based on image fusion to improve the color transient in the television(TV) receiver or in the MPEG decoder. Video image signals are composed of one luminance and two chrominance components, and the chrominance signals have been more band-limited than the luminance signals since the human eyes usually cannot perceive changes in chrominance over small areas. However, nowadays, as the advanced media like high-definition TV(HDTV) is developed, the blurring of color is perceived visually and affects the image quality. The proposed CTI method improves the transient of chrominance signals by exploiting the high-frequency information of the luminance signal. The high-frequency component extracted from the luminance signal is modified by spatially adaptive weights and added to the input chrominance signals. The spatially adaptive weight is estimated to minimize the ${\iota}_2-norm$ of the error between the original and the estimated chrominance signals in a local window. Experimental results with various test images show that the proposed algorithm produces steep and natural color edge transition and the proposed method outperforms conventional algorithms in terms of both visual and numerical criteria.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.896-905
• /
• 2004

In this paper, the design, fabrication and experiment on a planar array antenna with a flat-topped radiation pattern for a mobile base station antenna were described. The current distribution of an antenna aperture, which is easily realizable in a feeding network compared with the conventional one of sin(x)/x was optimized for shaping a desired flat-topped radiation pattern. The planar array antenna designed in this paper has a rectangular lattice and is composed of array elements of 16${\times}$8. Each radiating element, which is a microstrip element fed coaxially, has a linear vertical polarization and the feed network which use a Wilkinson power divider and a 180$^{\circ}$ ring hybrid coupler as a base element is designed. The flat-topped radiation pattern with 90$^{\circ}$ is shaped by 16 array elements with the element spacing of 0.55 λ$_{ο}$ in the azimuth plane, and the normal radiation pattern with 10$^{\circ}$ is shaped by 8 array elements with the element spacing of 0.65 λ$_{ο}$ in the elevation plane. Also, the planar array antenna is symmetrically divided into four parts. It consists of one hundred-twenty-eight radiating elements, thirty-two 1-4 column dividers, low 1-8 row dividers and one 1-4 input power divider. In order to verify electrical performances of the planar way antenna proposed in this paper, the experimental breadboard operated in tile band of 1.92～2.17 GHz(IMT2000 band) was fabricated, and its experimental results were a good agreement with simulation ones.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.2
• /
• pp.152-160
• /
• 2013

In this paper, to the aim of wideband SSN(Simultaneous Switching Noise) suppression characteristic, investigation of spiral resonator are used in conjunction with bead which is commonly used for noise suppression method. Bead works effectively to suppress the power noise up to the first harmonic of fundamental frequency, 0.8 GHz, and spiral resonator suppress noise well in the frequency range of SRF(Self Resonance Frequency) which is inversely proportional to the length of spiral. Thus, when bead used in conjunction with a spiral the noise suppression characteristic is determined by the one of higher impedance element of the two in the frequency range and achieves more broadband filtering characteristic. The case for using 22 nH bead turns out 4.8, 2.0, 0, and, 0.6 dB, and the case for using 22 nH bead in conjunction with 3-turns spiral achieves more wideband characteristic of 9.5, 8.3, 6.1, and 9.9 dB power noise suppression performances at the first, second, third, and fourth harmonics, respectively. The peak-to-peak voltage levels decrease from 76 mV to 56 mV using 22 nH bead, and the level decrease rapidly to 34 mV when using in conjunction with bead and 3-turn spiral. Thus more wideband SSN suppression characteristic can be achieved using bead with spiral.