• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.137-140
• /
• 2005

The electronic dispenser is composed of electronic part and mechanical part. Electronic part is consisted of input keypad, micro-controller, display module, and pump module. In this paper we designed micro-controller for electronic part. The micro-controller controls display module and pump module. The display module is composed by LCD device, and the pump module is composed by motor device. The micro-controller for an electronic dispenser is designed by VHDL. We used WX12864APl for the LCD device and SPS20 for the stepping motor. Also, the micro-controller is designed by Altera Quartus tool and verified with Agent 2000 Design-kit using APEX20K Device. In this paper, we present possibility to adopt of biotechnology field through designing of one-chip controller for an electronic dispenser.

• Journal of IKEEE
• /
• v.25 no.3
• /
• pp.517-527
• /
• 2021

This paper presents the phase-shift full-bridge DC-DC converter using the one-chip micom. The proposed converter primary is the full-bridge power topology that operates with the unipolar pulse-width modulation (PWM) by the phase-shift method, and the secondary is the full-bridge full-wave rectifier composed of four diodes. The control of proposed converter is performed by the one-chip micom and its MOSFET switches are driven by the bootstrap circuit. Thus the total system of proposed converter is simple. The proposed converter achieves high-efficiency using the resonant circuit and blocking capacitor. In this paper, first, the power-circuit operation of proposed converter is explained according to each operation mode. And the power-circuit design method of proposed converter is shown, and the software control algorithm on the micom and the feedback and switch drive circuits operating the proposed converter are described, briefly. Then, the operation characteristics of proposed converter are validated through the experimental results of a designed and implemented prototype converter by the shown design and implementation method in this paper. The highest efficiency in the results was about 92%.

• Journal of IKEEE
• /
• v.9 no.2 s.17
• /
• pp.101-107
• /
• 2005

This paper presents an one-chip controller for an electronic dispenser. The electronic dispenser is composed of electronic part and mechanical part. The electronic part is consisted of input keypad, micro-controller, display module, and pump module. In this paper we designed micro-controller for the electronic part. The micro-controller controls display module and pump module. The display module is composed by LCD device, and the pump module is composed by motor device . The micro-controller for an electronic dispenser is designed by VHDL. We used WX12864AP1 for the LCD device and SPS20 for the stepping motor. Also, the micro-controller is designed by Altera Quartus tool and verified with Agent 2000 Design-kit using APEX20K Device. In this paper, we present possibility to adopt of the biomedical device through the one-chip controller for the electronic dispenser.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.44-52
• /
• 2002

본 논문에서는 RF와 마이크로파 응용을 위한 MEMS 수동 소자에 대한 내용이다. 이 수동 소자들을 만들기 위해서 개발된 3타원 MEMS공정은 기존의 실리콘 공정과 완전한 호환성을 가지고 한 칩으로 집적화 시킬 수 있는 공정이다. 이 3차원 MEMS 공정은 기존 실리콘 긍정이 가지고 있는 한계를 극복하기 위한 방법으로써 개발되었다. 개발된 공정을 이용하여 실리콘 공정에서 구현할 수 없었던 좋은 성능의 인덕터, 트랜스포머 및 전송선을 RF와 마이크로파 응용을 위해서 구현하였다. 저 전압, 높은 차단율을 위한 push-pull 개념을 도입한 MEMS 스위치를 구현하였다. 또한 높은 Q를 갖는 MEMS 인덕터를 최초로 CMOS 칩과 집적화에 성공하여 600kHz 옵셋 주파수에서 -122 dBc/Hz의 특성을 갖는 2.6 GHz 전압 제어 발진기를 제작하였다.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.16 no.6
• /
• pp.241-246
• /
• 2021

In this paper, we developed the evaluation system for the active noise control so that the algorithms can be easily evaluated in real-time on the system. We implemented the active noise controller based on a single-chip with only additional op-amps for signal conditioning because the TMS320C280049 MCU includes almost all necessary peripherals for the active noise controller. Due to the difficulty in testing algorithms on embedded-type hardware unlike in computer simulation, we also developed GUI-based evaluation software which makes it simple to test algorithms on the hardware. Using the GUI software, we can optimize the parameters of the algorithms with ease in a specific noise environment because the parameters can be adjusted in real-time when the algorithm is running on the hardware.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.6
• /
• pp.8-17
• /
• 2010

This paper proposes a novel LCD CCFL-backlight electronic ballast using the phase-shift full-bridge inverter. The proposed electronic ballast reduces the ignition voltage and eliminates current spikes using the new digital dimming control applied with soft-starting. Thus the electronic ballast improves ignition behavior of the CCFL and hence increases the CCFL's life span. For this, this paper analyzes the full-bridge inverter topology of the proposed electronic ballast and explains the new digital dimming control algorithm applied to the ballast, briefly. And this paper shows a design example of the prototype circuit and explains an implementation method of the digital dimming control which is implemented on a single-chip microcontroller with software. This was implemented as actual prototype electronic ballast, and its experimental results showed that the proposed electronic ballast operates correctly. The ignition voltage of the prototype in the digital dimming operation was reduced about 30[%] compared with the conventional electronic ballast and there were not any current spikes.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.7
• /
• pp.513-518
• /
• 2016

The piezoelectric actuating device is known for its large power density and simple structure. It can generate a larger force than a conventional actuator and has also wide bandwidth with fast response in a compact size. To control the piezoelectric actuator, we need an analog signal conditioning circuit as well as digital microcontrollers. Conventional microcontrollers are not equipped with an analog part and need digital-to-analog converters, which makes the system bulky compared with the small size of piezoelectric devices. To overcome these weaknesses, we are developing a single-chip controller that can handle analog and digital signals simultaneously using mixed-signal FPGA technology. This gives more flexibility than traditional fixed-function microcontrollers, and the control speed can be increased greatly due to the parallel processing characteristics of the FPGA. In this paper, we developed a floating-point multiplier, PWM generator, 80-kHz power control loop, and 1-kHz position feedback control loop using a single mixed-signal FPGA. It takes only 50 ns for single floating-point multiplication. The PWM generator gives two outputs to control the charging and discharging of the high-voltage output capacitor. Through experimentation and simulation, it is demonstrated that the designed control loops work properly in a real environment.

• Journal of Industrial Technology
• /
• v.22 no.A
• /
• pp.89-94
• /
• 2002

In this paper, a Exhaust Flow Controller (EFC) technology for uniform application of film coater and developer device is introduced that spread and remove photo resister at semiconductor manufacturing process. Because developed EFC device uses differential pressure sensing method as a differential flow meter and embodied smart A/D conversion by using a one chip microprocessor and devised by feedback Servo control, It has shown excellent performance and stability evaluation, as maximum 2000L/min flow, capability of installation to actual semiconductor equipment.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.281-284
• /
• 2008

This paper describes ASIC design of multimedia SoC Platform. The implemented Platform consists of 32-bit OpenRISC1200 Microprocessor, WISHBONE on-chip bus, VGA Controller, Debug Interface, SRAM Interface and UART. The 32-bit OpenRISC1200 processor has 5 stage pipeline and Harvard architecture with separated instruction/data bus. The VGA Controller can display RCB data on a CRT or LCD monitor. The Debug Interface supports a debugging function for the Platform. The SRAM Interface supports 18-bit address bus and 32-bit data bus. The UART provides RS232 protocol, which supports serial communication function. The Platform is design and verified on a Xilinx VERTEX-4 XC4VLX80 FPGA board. Test code is generated by a cross compiler' and JTAG utility software and gdb are used to download the test code to the FPGA board through parallel cable. Finally, the Platform is implemented into a single ASIC chip using Chatered 0.18um process and it can operate at 100MHz clock frequency.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.11
• /
• pp.801-805
• /
• 2009

Hardware based dynamic voltage and frequency scaling is a promising technique to reduce power consumption in a globally asynchronous locally synchronous system such as a homogeneous or heterogeneous multi-core system. In this paper, FPGA prototype design of hardware based dynamic frequency scaling is proposed. The proposed techniques are applied to a FIFO based multi-core system for a software defined radio and Network-on-Chip based hardware MPEG2 encoder. Compared with a references system using a single global clock, the first prototype design reduces the power consumption by 78%, but decreases the performance by 5.9%. The second prototype design shows that power consumption decreases by 29.1% while performance decreases by 0.36%.