• Polymer(Korea)
• /
• v.27 no.4
• /
• pp.275-284
• /
• 2003

The positive temperature coefficient (PTC) effects of high density polyethylene (HDPE)/carbon black composite materials were investigated by enhancing adhesive characteristics of electrodes and controlling HDPE chemical crosslinking. When the silver paste was used as an electrode for the same 45 wt% HDPE/carbon composites, the resistance was over 1 $\Omega$, which should be compared with the resistance of 0.2 $\Omega$ for the dendritic copper electrode. In general, the silver-paste electrode exhibited higher electrical resistance than cupper electrode due to the interfacial resistance between the electrode and PTC composites. The HDPE/carbon composite exhibited typical PTC characteristics maintaining a constant resistance up to vicat point and showing a maximum at the melting point of HDPE. The crosslinked HDPE significantly decreased the negative temperature coefficient (NTC) phenomena, and desirably showed a constant or slightly increasing feature of electrical resistance in the high temperature region.

• Resources Recycling
• /
• v.27 no.1
• /
• pp.55-63
• /
• 2018

Physical property changes of printed circuit board (PCB) according to heat treatment conditions were investigated. The heat treatment was carried out in air and nitrogen atmosphere at temperature range from $200^{\circ}C$ to $325^{\circ}C$. Thermogravimetric analysis showed that the PCB was pyrolyzed in two steps. The thickness of PCB expanded by 11~28% at about $300^{\circ}C$ in both air and nitrogen atmosphere as layer disintegration occurred. Mechanical strength of PCB decreased from 338.4 MPa to 20.3~40.2 MPa due to the delamination caused by the heat treatment. The heated printed circuit boards were crushed and sieved for analysis of density distribution and liberation degree of copper according to particle size. As a result of the density distribution measurement, non metallic particles and copper particles were concentrated into different size range, respectively. The liberation degree of copper was improved from 9.3% to 100% at size range of $1,400{\sim}2,000{\mu}m$ by heat treatment.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.34-39
• /
• 2022

In this study, effects of ultrasonic energy on the cementation reaction and copper recovery rate were investigated for different types of iron samples, such as plate, chip, and powder, for recovering copper from waste etchant, which contained ~3.5% copper. The cementation reaction using the ultrasonic energy was more effective than the simple stirring reaction, with the former exhibiting a high copper recovery rate than the latter for the same time interval. When cementation was performed for 25 min with ultrasonic treatment, rather than simple stirring, the copper recovery rate of the plate, chip, and powder improved from 7.0% to 12.0%, 14.0% to 46.1%, and 41.9% to 77.2%, respectively. Therefore, the use of ultrasonic energy could detach the copper recovered by the cementation reaction from the surface of the iron samples, thereby increasing the copper recovery rate. Owing to the use of ultrasonic energy, the copper recovery rate increased by 2-6 times, and the recovered copper exhibited a decreased particle size compared to that obtained via simple stirring.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.6
• /
• pp.872-879
• /
• 2010

Layered copper hydroxides [LCHs, $Cu_2(OH)_3{\cdot}NO_3$] has the agricultural potentials as a fungicide because of its high crystallinity, excellent anion exchange capacity, and its regular layered particle size. The study, for the first time, has synthesized LCHs in highly concentrated solution and evaluated its physicochemical properties including the crystallinity and suspension stability. Optimal synthetic condition of LCHs was determined by crystallinity and stability of suspension as follow; 1) concentrations of $Cu(NO_3)_2$ and NaOH solutions were 3.0 M respectively, 2) reaction temperature and solution pH were $25^{\circ}C$ and 6.0, respectively, and 3) aging time after reaction was 2hr. Crystallinity of LCHs enhanced with increase in pH up to 9.0. Whereas, stability of suspension was decrease by increase in crystal size. Especially, increase in reaction temperature decreased stability of suspension. XRD patterns and SEM images exhibited that LCHs had regular layered particle size with 0.2~0.8 ${\mu}m$ and high crystallinity in optimal synthetic condition. The particle size was increased with increase in reaction temperature and pH. These results showed that LCHs synthesized in highly concentrated solution exhibited high stability of suspension as well as high crystallinity suitable to their potential as a fungicide.

• Journal of Conservation Science
• /
• v.27 no.1
• /
• pp.31-40
• /
• 2011

Copper-red (Dongwha, Jinsa) is Korean traditional inorganic pigment used for red-coloring on the porcelain surface during Goryeo and Joseon Periods. Trace amounts of copper-red porcelains are handed down because of the technical difficulty of making and coloring of the pigment. It is known that copper ore sources were extensively distributed in Korea according to old literatures and some of them are still producing copper ore at this present. Main types of copper-bearing mineral in Korea are chalcopyrite ($CuFeS_2$) and malachite ($Cu_2CO_3(OH)_2$), and they are easily collected from the ground surface. This means Korea had geographical and economic geological advantages for supplying raw material of the pigment. These two minerals showed good red-coloring in color test for porcelain pigment. As a coloring element, copper showed micro size less than $5{\mu}m$ in diameter in glaze matrix. The dispersion of copper particle is the most decisive factor for red chromaticity of copper-red porcelain, as well as copper content of the pigment.

• Resources Recycling
• /
• v.20 no.5
• /
• pp.64-68
• /
• 2011

The typical properties of manganese nodules are its high porosity and high specific surface area and manganese in nodules is existed as ${\delta}$-MnO$_2$. These properties suggest that manganese nodules ran be used as an adsorbent for heavy metal ions. This study investigated the practical applicability for the removal of copper ions in the waste water by manganese nodules as an adsorbent using fixed column and fix bed systems. Manganese nodules of 1kg (size 1-3 cm) can absorb 4.0g Cu in fixed column system and 2.3g Cu in fixed bed system from waste water for 3 hours respectively.

• Resources Recycling
• /
• v.28 no.5
• /
• pp.74-79
• /
• 2019

The effects of equivalent of iron powder, particle size, agitation speed on the removal efficiency of copper ion were investigated by adding iron powder as cementation agents to simulated mine drainage solution with 117.15 mg/L Cu ion. The 50 % of Cu was removed at 90 min with 2 equivalent of iron powder while more than 99 % of Cu was removed at 60 min with 16 equivalent at 200 rpm and $20^{\circ}C$. The removal efficiencies of Cu ion were not different using 2 equivalent of $48{\mu}m$ and $150{\mu}m$ iron powder, and the removal efficiency increased rapidly with increasing the agitation speed to more than 400 rpm. This lower removal efficiency resulted from agglomeration of iron powder observed by SEM, which could reduce the effective specific surface area. More than 99 % of copper ion was removed using 2 equivalent of $48{\mu}m$ iron powder at 60 min, 600 rpm and $20^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.29 no.6
• /
• pp.782-788
• /
• 2018

Submicron copper-silver core-shell (Cu@Ag) particles were synthesized using the sonochemical combined transmetallation reaction and the application to printed electronics as a low cost conductive paste was evaluated. $Cu_2O$ of the $Cu_2O/Cu$ composite used as a core in the reaction for the synthesis of core-shell was sonochemically reduced to Cu, and Cu atoms functioned as a reducer for silver ions in transmetallation to achieve the copper-silver core-shell structure. The characterization of submicron particles by TEM-EDS and TG-DSC confirmed the core-shell structure. Conductive pastes in which 70 wt% Cu@Ag was dispersed in solvents were prepared using a binder and wetting agents, and coated on the polyamide film using a screen-printing method. Printed paste films containing synthesized Cu@Ag particles with 8 at% and 16 at% Ag exhibited low resistivity of 96.2 and $38.4{\mu}{\Omega}cm$ after sintering at $180^{\circ}C$ in air, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.3
• /
• pp.37-42
• /
• 2007

Copper deposition studies have been actively studied since interests on 3D SiP were increased. The defects inside via can be easily formed due to the current density differences on entrance, bottom and wall of via. So far many different additives and current types were discussed and optimized to obtain void-free copper via filling. In this research acid cupric sulfate plating bath containing additives such as PEG, SPS, JGB, PEI and wave current applied electroplating were examined. The size and shape of grain were influenced by the types of organic additives. The cross section of specimen were analyzed by FESEM. When PEI was added, the denser copper deposits were obtained. Electroplaing time was reduced when 2 step via filling was employed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.7
• /
• pp.599-607
• /
• 2015

In this study, we theoretically investigate the thermal performances of heat pipes that have different nano-fluid properties. Two different types of nano-particles have been used: $Al_2O_3$ and CuO. The thermal performances of the heat pipes are observed for varying nano-particle aggregations and volume fractions. Both the viscosity and the conductivity increase as the volume fraction and the aggregation increase, respectively. Increasing the volume fraction helps increase the capillary limit in the well-dispersed condition. Whereas, the capillary limit is decreased under the aggregate condition, when the volume fraction increases. The dependence of the heat pipe thermal resistance on the volume fraction, aggregation, and conductivity of the nano-particles is analyzed. The maximum thermal transfer of the heat pipe is highly dependent on the volume fraction because of the high permeability of the heat pipe. For the proposed heat pipe, the optimum volume fraction of the nano-particle can be seen through 3D graphics.