• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.4
• /
• pp.19-23
• /
• 2012

Silicon substrate for light emitting diodes (LEDs) has been the tendency of LED packaging for improving power consumption and light output. In this study, a low cost and high throughput Si through via fabrication has been demonstrated using a wet etching process. Both a wet etching only process and a combination of wet etching and dry etching process were evaluated. The silicon substrate with Si through via fabricated by KOH wet etching showed a good electrical resistance (${\sim}5.5{\Omega}$) of Cu interconnection and a suitable thermal resistance (4 K/W) compared to AlN ceramic substrate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.94-94
• /
• 2004

고성능 섬유강화 복합재료는 단위 중량당 강성과 강도가 높으면서 가격도 저렴하여 여러 산업분야에서 널리 사용되고 있으며 특히, 경량임에도 충격에 대한 저항성이 우수하여 방탄재료로의 군사적, 민간용 이용도가 날로 증가되고 있다. 그러나 고속 충격 탄자와 같이 관통성이 뛰어난 위협 조건으로부터의 방호를 목적으로 장갑을 설계할 매는 단일 재료만으로는 충분한 방탄 성능을 가질 수 없는 경우가 많다. 이런 경우는 충격 전면에서 충격 탄자의 탄두를 일차적으로 무디게 하거나 파쇄시켜 탄자의 형상을 변화시키고, 변형된 탄자의 계속적인 관통에 대한 저항능력이 우수한 재료를 사용하여 두가지 성질을 동시에 만족시키는 장갑재료의 개발이 요구되고 꾸준히 연구되어 왔다.(중략)

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.267-272
• /
• 2003

In order to investigate the effect of face material on Ti/Al alloy laminates under high velocity impact, a ballistic testing was conducted. Ballistic resistance of these materials was measured by protection ballistic limit($V_{50}$), a statistical velocity with 50% probability penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, were respectfully observed, by $V_{50}$ test and Projectile Through Plates (PTP) test at velocities greater than $V_{50}$. PTP tests were conducted with $0^{\circ}$obliquity at room temperature using 5.56mm ball projectile. $V_{50}$ tests with $0^{\circ}$obliquity were also done with projectiles that were able to achieve near or complete penetration during PTP tests. Resistance to penetration, and penetration modes which face material was Titanium alloy, were compared to those which face material was anodized Al alloy after cold-rolling.

• Composites Research
• /
• v.24 no.2
• /
• pp.46-50
• /
• 2011

This paper describes the state of the art for the development of metallic armor materials which are mainly used as armor plates of the combat vehicles. Several important micro-structural features affecting ballistic properties of the metallic armor are discussed. Optimization of the strength and toughness balance of the metallic armor is necessary for the improvement of the ballistic performance resulting from maximizing the resistance to the penetration of the bullet and also to brittle failure of the plates. Understanding and control of the adiabatic shearing phenomenon developed remarkably during high strain rate deformation is needed to prevent brittle failure of the metallic armor materials.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.3A
• /
• pp.375-381
• /
• 2008

This paper deals with the shear capacity of corrugated rib as the shear connector in composite structures. Corrugated rib is modified as perfobond rib shear connector type to evaluate the shear capacity. A total 12 push-out specimens with stud, perfobond rib, and corrugated rib connector were fabricated. Then, the influences of hole-crossing bars, concrete dowel, depth of corrugated panel and height of rib on the shear capacity were evaluated experimentally. As the results of these tests, the failure mechanisms of corrugated rib and perfobond rib specimens were associated with the bearing failure of the concrete slabs, but the failure of weld zone did not occur. The shear capacity of corrugated rib specimens improved as high to 96% compared to the perfobond rib shear connectors. Also, the hole-crossing bars were effective on the improvement of concrete dowel action, and consequently, shear capacity increased by 48%. It was also proven that the increment of the depth of corrugated panel and the height of rib increased the concrete bearing resistance, therefore increasing the shear capacity.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.112-117
• /
• 2008

Vertical interconnection scheme using novel silicon-through-via for 3D MEMS devices or stacked package is proposed and fabricated to demonstrate its feasibility. The suggested silicon-through-via replaces electroplated copper, which is used as an interconnecting material in conventional through-via, with doped silicon. Adoption of doped silicon instead of metal eliminates thermal-mismatch-induced stress, which can make troubles in high temperature MEMS processes, such as wafer bonding and LP-CVD(low pressure chemical vapor deposition). Two silicon layers of $30{\mu}m$ thickness are stacked on the substrate. The through-via arrays with spacing $40{\mu}m$ and $50{\mu}m$ are fabricated successfully. Electrical characteristics of the through-via are measured and analyzed. The measured resistance of the silicon-through-via is $169.9\Omega$.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.12
• /
• pp.126-134
• /
• 2003

In order to investigate the effect of surface treatment in Aluminium alloy and Titanium alloy which are used to armor material during ballistic impact, a ballistic testing was conducted. Anodizing was used to achieve higher surface hardness of Aluminium alloy and Iron plating in PVD(Physical Vapor Deposition) method was used to achieve higher surface hardness of Titanium alloy. Surface hardness test were conducted using a Micro victor's hardness tester. Ballistic resistance of these materials was measured by protection ballistic limit(V-50), a statical velocity with 50% probability penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are respectfully observed from the results of V-50 test and Projectile Through Plates (PTP) test at velocities greater than V-50. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature using 5.56mm ball projectile. V-50 tests were conducted with 0$^{\circ}$obliquity at room temperature with projectiles that were able to achieve near or complete penetration during PTP tests. Surface hardness, resistance to penetration. and penetration modes of surface treated alloy laminates are compared to those of surface non-treated alloy laminates. A high speed photography was used to analyze the dynamic perforation phenomena of the test materials.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.32 no.1
• /
• pp.17-20
• /
• 1995

고전적인 고속선형에서 탈피한 새로운 형태의 고속선형에 대한 효시는 1960년경의 수중관통형 수중익선의 개발이라 할 수 있다. 그 후, 1980년대까지는 일반적인 중,저 속의 화물선 및 LNG 운반선에 대한 유체역학적 특성의 향상을 위한 선형 개발 경쟁이 국내외적으로 활발하게 진행 되어져 왔다. 그러므로, 이러한 기간중인 약 20여년간은, 선박의 선형 개발면에서는 기존의 선 박형태를 탈피하지 못한 채 유체역학적 성능을 향상시키려는 소극적인 진전이 있었을 뿐, 발전이 매우 더딘 편이었다. 1980년대 후반에 들어서 국내외적인 물동량의 증가와 해상고속운송의 필 요성이 대두되면서 고속선의 개발에 대한 열기가 시작되었다. 그간의 고속선개발은 주로 미국을 중심으로 군사적인 목적면에서 진행되어 왔고, 일본은 거의 일반상선의 선형개발에 중점을 두어 왔으나, 1980년대 후반부터는 일본도 아시아지역에서의 물동량변화와 고속화의 필요성에 따라 고속선 개발에 뛰어들게 되었다[1, 2, 3]. 특히 최근의 50knots를 넘는 대형의 화물운송용 초고 속선 개발은 주목할 만한 연구가 되고 있다'4'. 국내에서도 1990년대에 들어서면서 소형이지만 이러한 초고속선의 선형개발을 시작하게 되었으며, 실용화된 예도 몇몇을 가지고 있다. 본고에 서는 이제까지 연구된 몇가지 초고속선형들에 대한 예와 장단점, 또한 조파저항 성능면에 대해 기술하여 보고자 한다.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.2
• /
• pp.127-137
• /
• 1992

원자력발전소의 콘크리트 격납용기구조물등과 같이 안전성이 높게 요구되는 구조물들은 예기치 않은 혹은 부주의한 사고로 인하여 발생하는 비산물체에 의한 충격에 충분히 저항할 수 있도록 설계되어야 한다. 이러한 물체에 의한 충격은 벽면의 국부적인 피해와 벽 전체의 전반휨응답으로 나타나며, 이에 저항하기 위해서는 벽체의 관통이나 스캐빙(scabbing)이 일어나지 않도록 벽두께를 결정하여야 하고 또한, 파괴가 일어나지 않도록 벽체를 설계하여야 한다. 본 논문에서는 지금까지 연구된 충격현상에 대한 이론 및 실험결과를 토대로 하여 벽면의 국부효가 발생시 이와 동시에 진행되는 탄성효과 및 전반거동효과를 고려하여 관입깊이를 계산할 수 있는 이론을 유도하였으며, 기존의 실험결과를 이용하여 이론적인 결점을 보완한 반이론식을 제안하였다. 또한, 본 논문에서는 실험결과와 기존식성충격과 소성충격을 구분짓는 스폴링속도에 대한 개념을 제시하였다. 본 논문은 충격을 받는 철근콘크리트 구조물의 벽체설계에 유용한 토대를 제공할 것으로 사료된다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.11
• /
• pp.1257-1264
• /
• 2014

Efforts are presently underway for developing an optimal design methodology for GEN-IV nuclear reactors based on target failure probabilities. A typical example is the system-based code, in which the results are represented in the form of partial safety factors (PSFs). Thus, a PSF is one of the crucial elements in either component design or integrity assessment based on target failure probabilities during the operation period. In the present study, a procedure for calculating the PSF of a circumferential through-wall cracked pipe based on the elastic-plastic crack initiation criterion is established, in which the importance of each input variable is assessed. Elastic-plastic J-integrals are calculated using the GE/EPRI and reference stress methods, and the PSF values are calculated using both first- and second-order reliability methods. Moreover, the effect of statistical distributions of assessment variables on the PSF is also evaluated.