• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.125-125
• /
• 2018

반도체 소자의 미새화에 따라 선폭이 10nm 이하로 줄어듦에 따라, 금속 배선의 저항이 급격하게 상승하고 있다. Cu는 낮은 저항과 높은 전도도를 가지고 있어 현재 배선물질로써 가장 많이 사용되고 있지만, 소자가 미세화됨에 따라 Cu를 미래의 배선물질로써 계속 사용하기에는 몇 가지 문제점이 제기되고 있다. Cu는 electron mean free path (EMFP)가 39 nm로 긴 특성을 가지기 때문에, 선폭이 줄어듦에 따라 surface 및 grain boundary scattering이 증가하여 저항이 급격하게 증가한다. 또한, technology node에 따른 소자의 operating temperature와 current density의 증가로 인해 Cu의 reliability가 감소하게 된다. 텅스텐은 EMFP가 19 nm로 짧은 특성을 가지고 있어, 소자의 크기가 줄어듦에 따라 Cu보다 낮은 저항 특성을 가질 수 있으며, 녹는점이 3695K로 1357K인 Cu보다 높으므로 배선물질로써 Cu를 대체할 가능성이 있다. 본 연구에서는 Inductively Coupled Plasma (ICP) assisted magnetron sputtering을 통해 매우 얇은 텅스텐 박막을 증착하여 저항을 낮추고자 하였다. 고밀도 플라즈마의 방전을 위해, internal-type coil antenna를 사용하였으며 텅스텐 박막의 증착을 위해 DC sputter system이 사용되었다. 높은 에너지를 가진 텅스텐 이온을 이용하여 낮은 온도에서 고품위 박막을 증착할 수 있었으며, dense한 구조의 박막 성장이 가능하였다. ICP assisted를 이용하여 증착했을 때와, 그렇지 않을 때를 비교하여 ICP 조건에 따라서 박막의 저항이 감소함을 확인할 수 있었을 뿐만 아니라 최대 약 65% 감소함을 확인할 수 있었다. XRD를 이용하여 ICP power를 인가했을 때, 높은 저항을 갖는 A-15 구조를 가진 ${\beta}$ peak의 감소와 낮은 저항을 갖는 BCC 구조를 가진 ${\alpha}$ peak의 증가를 상온과 673K에서 증착한 박막 모두에서 확인하였으며, 이를 통해 ICP power가 저항 감소에 영향을 미친다는 것을 확인하였다. 또한, 두 온도 조건에서 grain size를 계산하여 ICP power를 인가함에 따라 두 조건 모두 grain size가 증가하였음을 조사하였다. 또한, XPS 분석을 통해 ICP power를 인가하였을 때 박막의 저항에 많은 영향을 끼치는 O peak이 감소하는 것을 통해 ICP assisted의 효과를 확인하였다. 이를 통해, ICP assisted magnetron sputtering을 통해 텅스텐 박막을 증착함으로써 차세대 배선물질로써 텅스텐의 가능성을 확인할 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1187-1194
• /
• 2003

A BCl$_3$/Ne plasma chemistry was used to etch Ga-based (GaAs, AIGaAs, GaSb) and In-based (InGaP, InP, InAs and InGaAsP) compound semiconductors in a Planar Inductively Coupled Plasma (ICP) reactor. The addition of the Ne instead of Ar can minimize electrical and optical damage during dry etching of III-V semiconductors due to its light mass compared to that of Ar All of the materials exhibited a maximum etch rate at BCl$_3$ to Ne ratios of 0.25-0.5. Under all conditions, the Ga-based materials etched at significantly higher rates than the In-based materials, due to relatively high volatilities of their trichloride etch products (boiling point CaCl$_3$ : 201 $^{\circ}C$, AsCl$_3$ : 130 $^{\circ}C$, PCl$_3$: 76 $^{\circ}C$) compared to InCl$_3$ (boiling point : 600 $^{\circ}C$). We obtained low root-mean-square(RMS) roughness of the etched sulfate of both AIGaAs and GaAs, which is quite comparable to the unetched control samples. Excellent etch anisotropy ( > 85$^{\circ}$) of the GaAs and AIGaAs in our PICP BCl$_3$/Ne etching relies on some degree of sidewall passivation by redeposition of etch products and photoresist from the mask. However, the surfaces of In-based materials are somewhat degraded during the BCl$_3$/Ne etching due to the low volatility of InCl$_{x}$./.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.5 s.347
• /
• pp.11-16
• /
• 2006

This paper reports the correlation between dielectric constant and degree of amorphism of the hybrid type SiOC thin films. SiOC thin films were deposited by high density plasma chemical vapor deposition using bistrimethyl- silylmethane(BTMSM,$H_{9}C_{3}-Si-CH_{2}-Si-C_{3}H_{9}$) and oxygen precursors with various flow rate ratio. As-deposited film and annealed films at $400^{\circ}C$ were analyzed by XRD. The SiOC thin films were amorphous from XRD patterns. For quantitative analysis, the diffraction pattern of the samples was transformed to radial distribution function by Fourier analysis, and then compared with each other. The degree of amorphism of annealed films was higher than that of as-deposited ones. The dielectric constant varied in accordance with flow rate ratio of precursors. The lowest dielectric constant was obtained from the as-deposited film which has the highest degree of amorphism after annealing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.826-830
• /
• 2013

In this paper, we carried out the investigations of both etch characteristics and mechanisms for the $SnO_2$ thin films in $O_2/BCl_3/Ar$ plasma. The dry etching characteristics of the $SnO_2$ thin films was studied by varying the $O_2/BCl_3/Ar$ gas mixing ratio. We determined the optimized process conditions that were as follows: a RF power of 700 W, a DC-bias voltage of - 150 V, and a process pressure of 2 Pa. The maximum etch rate was 509.9 nm/min in $O_2/BCl_3/Ar$=(3:4:16 sccm) plasma. From XPS analysis, the etch mechanism of the $SnO_2$ thin films in the $O_2/BCl_3/Ar$ plasma can be identified as the ion-assisted chemical reaction while the role of ion bombardment includes the destruction of the metal-oxide bonds as well as the cleaning of the etched surface form the reaction products.

• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.853-856
• /
• 2005

Inductively coupled plasma reactive ion etching of magnetic tunnel junction (MTJ) stack, which is one of the key elements in magnetic random access memory, was studied. The MTJ stacks were patterned in nanometer size by electron(e)-beam lithography, and TiN thin films were employed as a hard mask. The etch process of TiN hard mask was examined using Ar, $Cl_2/Ar$, and $SF_6/Ar$. The TiN hard mask patterned by e-beam lithography was first etched and then the etching of MTJ stack was performed. The MTJ stacks were etched using Ar, $Cl_2/Ar$, and $BCl_3/Ar$ gases by varying gas concentration and pressure.

• Korean Journal of Materials Research
• /
• v.13 no.12
• /
• pp.775-778
• /
• 2003

We studied InP etching in high density planar inductively coupled $BCl_3$and $BCl_3$/Ar plasmas(PICP). The investigated process parameters were PICP source power, RIE chuck power, chamber pressure and $BCl_3$/Ar gas composition. It was found that increase of PICP source power and RIE chuck power increased etch rate of InP, while that of chamber pressure decreased etch rate. Etched InP surface was clean and smooth (RMS roughness <2 nm) with a moderate etch rate (300-500 $\AA$/min) after the planar $BCl_3$/Ar ICP etching. It may make it possible to open a new regime of InP etching with $CH_4$$H_2$-free plasma chemistry. Some amount of Ar addition (<50%) also improved etch rates of InP, while too much Ar addition reduced etch rates of InP.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.97-101
• /
• 2009

In the modem semiconductor industry, the progress that consumes the most capital and labor is cleansing process. Cleansing process is to remove impurities that can affect the operation of the device and deteriorate its function. Especially, Photoresist (PR) progress that etches the device always requires cleansing at the end of the progress. Also, HDI-PR (High-Dose Ion-implanted Photoresist) created from PR progress is difficult to remove. Thus, in modem IC cleansing, many steps of cleansing are used, including dry and wet cleansing. In this paper, we suggested to combine existing dry-cleansing and wet-cleansing, each represented by plasma cleansing and stripper solution, as Plasma Liquid-Vapor Activation (PLVA). This PLVA method enhances the effect of existing cleansing solution, and decreases the amount of solution and time required to strip. We stripped HDI-PR by activated solution and measured surface hardness and Young's modulus by Nano-indenter. Nano-indenter is the equipment that determines the hardness and the modulus of elasticity by indenting nano-sized tip with specific shape into the surface and measuring weight and z-axis displacement. We measured the change of surface hardness and Young's modulus before and after the cleansing. As a result, we found out that the surface hardness of the sample sharply decreased after the cleansing by plasma-activated PR stripper solution. It can be considered that if physical surface-cleansing process is inserted after this, more effective elimination of HDI-PR is possible.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1129-1136
• /
• 1999

TIN films were prepared on Si(100) substrate by ICP-CVD(inductive1y coupled plasma enhanced chemical vapor deposition) using TEMAT(tetrakis ethylmethamido titanium : Ti$[\textrm{N}\textrm{(CH)}_{3}\textrm{C}_{2}\textrm{H}_{5}]_{4}$) precursor at various deposition conditions. Phase, microstructure, and the electrical properties of TIN films were characterized by x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (HRTEM) and electrical measurements. Polycrystalline TiN films with B1 structure were grown at temperatures over $200^{\circ}C$. Preferentially oriented along TiN(111) films were obtained at temperatures over $300^{\circ}C$ with the flow rates of 10, 5, and 5 sccm for TEMAT, $\textrm{N}_{2}$ and Ar gas. The TiN/Si(100) interface was flat and no chemical reaction between TIN and $\textrm{SiO}_2$ was found. The resistivity, carrier concentration and the carrier mobility for the TiN sample prepared at $500^{\circ}C$ are 21 $\mu\Omega$cm, 9.5$\times\textrm{10}^{18}\textrm{cm}^{-3}$ and $462.6\textrm{cm}^{2}$/Vs, respectively.

• Korean Journal of Materials Research
• /
• v.15 no.3
• /
• pp.161-165
• /
• 2005

We investigated selective dry etching of GaAs over AlGaAs and InGaP in high density planar inductively coupled $BCl_3/SF_6$ plasmas. The process parameters were ICP source power (0-500 W), RE chuck power (0-30W) and gas composition $(60-100\%\;BCl_3\;in\;BCl_3/SF_6)$. The process results were characterized in terms of etch rate, selectivities of GaAs over AlGaAs and InGaP, surface morphology, surface roughness and residues after etching. $BCl_3/SF_6$ selective etching of GaAs showed quite good results in this study. Selectivities of GaAs $(GaAs:AlGaAs\~36:1,\;GaAs:InGaP\~45:1)$ were superior at $18BCl_3/2SF_6$, 20 W RF chuck power, 300 W ICP source power and 7.5 mTorr. Addition of $(5-15\%)SF_6\;to\;BCl_3$ produced relatively high selectivities of GaAs over AlGaAs and InGaP during etching due to decrease of etch rates of AlGaAs and InGaP (boiling points of etch products: $AlF_3\~1300^{\circ}C,\;InF_3>1200^{\circ}C$ at atmosphere) at the condition. SEM and AFM data showed slightly sloped sidewall and somewhat rough surface$(RMS\~9nm)$. XPS study on the surface of processed GaAs proved a very clean surface after dry etching. It shows that planar inductively coupled $BCl_3/SF_6$ plasmas could be a good candidate for selective dry etching of GaAs over AlGaAs and InGaP.