• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.941-945
• /
• 2007

도시하천에서 환경적 기능이 중요성을 더해가면서 복단면의 홍수터에 교목이 식재 되어지는 경우가 있다. 그러나 식생은 하천의 흐름저항을 크게 하고 통수능을 감소시켜 수위상승이나 국부적인 유속 증가를 유발할 수 있으므로 하천에 식생대를 조성하거나 향후 관리를 위해서는 식재로 인해 변화되는 수리학적 특성들을 이해하는 것이 무엇보다 중요하다. 따라서 본 연구에서는 하천복원의 주 대상이 될 수 있는 도시하천의 홍수터에 교목의 식재 가능성을 알아보기 위해 수리실험을 실시하였다. 실험수로는 우리나라 도시하천의 대부분이 홍수터를 갖는 복단면임을 고려하여 복단면 형태로 제작하였으며, 실험은 길이 16 m, 폭 0.8 m, 높이 0.9 m이고 벽면이 아크릴로 된 직사각형 가변 경사 개수로 실험 장치를 이용하였다. 수로경사는 0.5 %, 실험 식생의 밀도는 4.4 %로 고정하고, 실험유량을 $0.03{\sim}0.04\;m^3/s$, 수심(h)과 홍수터 폭(w)의 비(h/w)를 1.2, 1.7, 2.2로 변화시키면서 실험을 실시하였다. 실험결과 최대 수심변화는 유량이 $0.04\;m^3/s$이고 수심/홍수터 폭 비가 1.2일때 약 4 %로 측정되었고, 저수로에서의 유속의 증가 범위는 단면 평균유속에 비교하여 약 $50{\sim}85\;%$로 확인되었다. 이는 복단면에서의 저수로 유속은 홍수터에 식재가 되었을 경우가 그렇지 않은 경우에 비해 더욱 빨라짐을 의미한다. 따라서 복단면의 홍수터에 교목을 식재할 경우에는 식재에 의한 수위상승 영향 보다는 저수로에서의 유속증가에 더 많은 관심을 가질 필요가 있다고 판단된다.

• Journal of the Korean Vacuum Society
• /
• v.8 no.1
• /
• pp.75-82
• /
• 1999

Ion energy is one of the crucial property in thin film deposition by internal ICP assisted I-PVD. As ion energy is determined by the difference between the plasma potential and the substrate bias potential, ICP excitation frequency was tested with medium frequency of 4 MHz and two types of tuning circuits, alternate and floating LC network with a biasing resistor, were tested. The results showed that plasma potential was less than 5 V in a range of Ar pressures, 5mTorr to 30 mTorr, at 4 MHz RF 600 W and 60 V of maximum RF antenna voltage was maintained either at RF input or output terminal. By proper control of RLC circuit installed after after RF antenna, 50V of RF induced voltage on RF antenna was obtained at 500W input power. The total impedance of RF antenna and plasma was around 10$\Omega$, and minimum RF voltage was obtained with a condition of lowest reactance at most 0.05$\Omega$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.282-282
• /
• 2010

결정질 태양전지는 상대적으로 고효율이 보장되며, 낮은 공정 비용 등의 이유로 널리 사용되고 있는 기술이다. 결정질 태양전지의 효율을 증가시키는 공정 방법에는 표면 구조화, 도핑 농도, 반사방지막, 금속전극 형성 등이 있다. 특히, 도핑 공정에서 도핑 농도를 변화시킬 수 있으며, 이에 의하여 면 저항값을 변화 시킬 수 있다. 본 연구에서는 결정질 태양 전지에서 도핑 농도의 조절에 의한 이상적인 sheet resistance를 얻기 위한 실험을 진행하였다. 3개의 실험 set을 두고 각각의 경우를 실험하였다. 본 연구에서는 Pre-deposition과 drive-in 방법을 사용한 doping의 2가지 step으로 실험을 진행하였다. pre-deposition의 시간 condition은 21분으로 하였다. $N_2$ 분위기에서 $O_2$와 $POCl_3$ 의 비율을 각각 100sccm, 200sccm으로 하여 실험을 진행하였다. 변수인 온도의 경우는 각각의 set에 대하여, $830^{\circ}C$, $840^{\circ}C$, $850^{\circ}C$ 로 가변하였다. pre-deposition을 끝낸 뒤, sheet resistance의 값은 각각 $75{\sim}90\;\Omega/square$, $68{\sim}75\;\Omega/square$, $56{\sim}63\;\Omega/square$의 값을 나타내었다. 도핑의 경우에는 drive-in 방법을 사용하였으며, 모든 경우에서 20분에서 $890^{\circ}C$에서 진행하였다. 최종 sheet resistance의 값은 각각의 경우 최대 $33\;\Omega/square$, $34\;\Omega/square$, $30\;\Omega/square$의 값을 나타내었다. $40{\sim}45\;\Omega/square$ 정도의 sheet resistance가 많은 연구에서 이상적인 sheet resistance로 연구되고 있다. 본 연구에서 두 번째 조건이 이상적인 sheet resistance에 가장 접근 하였음을 확인 할 수 있다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.11
• /
• pp.915-922
• /
• 2006

Considering heat pipe design principles in fabrication and operational performances, water is one of the most recommended working fluids to make mid to low tempera lure heat pipes. But the conventional water heat pipes might encounter the failure in a cold start-up operation when socked at a chilling temperature lower than the freezing point. If they are subjected to a heat supply for start-up at a temperature around $-20^{\circ}C$, the rate of the vapor flow and the corresponding heat transfer from the evaporator to the condenser is so small that the vapor keeps to stick on the surface of the chilling condenser wall, forming an ice layer, resulting in a liquid deficiency in the evaporator. This kind of problems was resolved by Kang et al. in 2004 by adopting a gas loading heat pipe technology to the conventional water heat pipes. This study was conducted to examine a chilling start-up procedure of gas loading heat pipes by investigating the behaviors of heat pipe wall temperatures. And the thermal resistance of the gas loaded heat pipe that depends on the operating temperatures and heat loads was measured and examined. Two water heat pipes were designed and fabricated for the comparison of performances, one conventional and the other loaded with $N_2$ gas. They were put on start-up test at a heat supply of 30 W after having been socked at an initial temperature around $-20^{\circ}C$. It was observed that the gas loaded one had succeeded in chilling start-up operation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.617-631
• /
• 2019

In the four-step demand model, a gravity mode is used most commonly at the trip distribution stage. The purpose of this study was to develop a new friction factor that can express the accessibility property as a single friction factor to compensate for the variable limits of the gravity model parameters (travel time, travel cost). To derive a new friction factor, a new friction factor was derived using the space syntax that can quantify the characteristics of the urban space structure, deriving the link-unit integration degree and then using the travel time and travel distance relationship. Calibration of the derived friction factor resulted in a similar level to that of the existing friction factor. As a result of verifying the various indicators, the explanatory power was found to be excellent in the short - and long - distance range. Therefore, it is possible to derive and apply the new friction factor using the integration index, which can complement the accessibility beyond the limit of the existing shortest distance, and it is believed to be more advantageous in future utilization.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.599-604
• /
• 1998

We have investigated Pt and $RuO_2$ as a bottom electrode for ferroelectric capacitor applications. The bottom electrodes were prepared by using an RF magnetron sputtering method. Some of the investigated parameters were a substrate temperature, gas flow rate, RF power for the film growth, and post annealing effect. The substrate temperature strongly influenced the surface morphology and resistivity of the bottom electrodes as well as the film crystallographic structure. XRD results on Pt films showed a mixed phase of (111) and (200) peak for the substrate temperature ranged from RT to $200^{\circ}C$, and a preferred (111) orientation for $300^{\circ}C$. From the XRD and AFM results, we recommend the substrate temperature of $300^{\circ}C$ and RF power 80W for the Pt bottom electrode growth. With the variation of an oxygen partial pressure from 0 to 50%, we learned that only Ru metal was grown with 0~5% of $O_2$ gas, mixed phase of Ru and $RuO_2$ for $O_ 2$ partial pressure between 10~40%, and a pure $RuO_2$ phase with $O_2$ partial pressure of 50%. This result indicates that a double layer of $RuO_2/Ru$ can be grown in a process with the modulation of gas flow rate. Double layer structure is expected to reduce the fatigue problem while keeping a low electrical resistivity. As post anneal temperature was increased from RT to $700^{\circ}C$, the resistivity of Pt and $RuO_2$ was decreased linearly. This paper presents the optimized process conditions of the bottom electrodes for memory device applications.

• Journal of Navigation and Port Research
• /
• v.30 no.10 s.116
• /
• pp.847-853
• /
• 2006

In this paper, we designed VCO(voltage controlled oscillator} that is composed of a dielectric resonator and a varactor diode, and the PLDRO(phase locked dielectric resonator oscillator) that is combined with the sampling phase detector and loop filter. The results at 12.05 GHz show the output power is 13.54 dBm frequency tuning range approximately +/- 7.5 MHz, and power variation over the tuning range less than 0.2 dB, respectively. The phase noise which effects on bits error rate in digital communication is obtained with -114.5 dBc/Hz at 100 kHz offset from carrier, and The second harmonic suppression is less than -41.49 dBc. These measured results are found to be more improved than those of VCO without adopting PLL, and the phase noise and power variation performance characteristics show the better performances than those of conventional PLL.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2359-2368
• /
• 2013

In this paper, an IRD (internal read data) circuit preventing the reentry into the read mode while keeping the read-out DOUT datum at power-up even if noise such as glitches occurs at signal ports such as an input signal port RD (read) when a power IC is on, is proposed. Also, a pulsed WL (word line) driving method is used to prevent a DC current of several tens of micro amperes from flowing into the read transistor of a differential paired eFuse OTP cell. Thus, reliability is secured by preventing non-blown eFuse links from being blown by the EM (electro-migration). Furthermore, a compared output between a programmed datum and a read-out datum is outputted to the PFb (pass fail bar) pin while performing a sensing margin test with a variable pull-up load in consideration of resistance variation of a programmed eFuse in the program-verify-read mode. The layout size of the 8-bit eFuse OTP IP with a $0.18{\mu}m$ process is $189.625{\mu}m{\times}138.850{\mu}m(=0.0263mm^2)$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.5
• /
• pp.51-57
• /
• 2015

In this paper, in order to design the A / D converter with a high resolution of 14 bits or more for the biological signal processing, CMOS delta sigma modulator that is a 1.8V power supply voltage - were designed. we propose a new structure of The fourth order delta-sigma modulator that needs four op amps but we use only two op amps. By using a time -interleaving technique, we can re-construct the circuit and reuse the op amps. Also, we proposed a KT/C noise reduction circuit to reduce the thermal noise from a noisy resistor. We adjust the size of sampling capacitor between sampling time and integrating time, so we can reduce almost a half of KT/C noise. The measurement results of the chip is fabricated using a Magna 0.18um CMOS n-well1 poly 6 metal process. Power consumption is $828{\mu}W$ from a 1.8V supply voltage. The peak SNDR is measured as a 75.7dB and 81.3dB of DR at 1kHz input frequency and 256kHz sampling frequency. Measurement results show that KT/C noise reduction circuit enhance the 3dB of SNDR. FOM of the circuit is calculated to be 142dB and 41pJ / step.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.4
• /
• pp.287-294
• /
• 2016

Based on upper limb torque by different angles of a back, distance between crank axis and chest and angles of hand-grips, this research is to develop variable hand bikes. By doing so, it is to offer guidance for its design. For this research three normal persons took part in the experiment. Results are as follows. First, upper limb torque was found to be the highest at 50 degree of a back and muscle endurance was shown to be the highest at 80 degree of a back. It means that as a back of a chair gets lower the speed and efficiency becomes better, which contradicts the subjective fact that K-type hand bikes would show the highest speed. Second, among types of grips of hand bikes 45 degree ones have been shown to be the ones with the highest torque. This is due to proper distribution of power of joints in arms, elbows, and shoulders. Third, in case of distance of 45cm between crank axis and chest, it has shown the most efficient torque. This is because of the effect of gravity and exhaustion when handling.