• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2002년도 제3회 최신 분말제품 응용기술 Workshop
• /
• pp.133-155
• /
• 2002

1. Quasicrystalline powders shows exotic physical and mechanical p properties 2. Applications: structural application: strengthening particles for composites C Coating application: wear resistance, low friction coefficient 3. For thermal spaying: material loss during process should be c considered to control chemical composition of deposit 4. Friction coefficient is strongly dependent on contact geometry F Friction coefficient from pin on plate: 0.1-0.2 Friction coe야icient from flat on plate: about 0.46. 5. Quasicrystalline materials show lower friction coefficient but higher w wear rate than corresponding values of $Cr_20_3$ coated layer. 6. Amorphous coating seems to be promising

• 한국식품저장유통학회지
• /
• 제7권3호
• /
• pp.267-272
• /
• 2000

건고추로부터 올레오레진을 신소가게 추출하고자 기존 추출방법들에 비하여 신속성과 환경친화성이 인정되고 있는 극초단파 추출공정에 필요한 몇 가지 기본조건을 검토하였다. 극초단파 추출에서 건고추의 입자 크기는 60 mesh, 시료와 용매(에탄올)의 비는 1:10(g/mL)이 적당하였고, 에너지 용량은 50 W에서 올레오레진과 capsanthin에 대한 추출효율이 가장 높게 나타났다. 가용성 고형분은 에탄올농도가 낮을수록 증가하였으나 capsanthin 함량은 75% 이상의 에탄올 농도에서 높은 증가현상을 나타내었다. 극초단파에 의한 올레오레진과 capsanthin의 추출은 짧은 시간에 이루어지므로 1회 추출시간은 3~5분이 적당한 것으로 나타났다.

• 공업화학
• /
• 제8권2호
• /
• pp.292-300
• /
• 1997

본 연구에서는 출발물질을 변화시켜 입방체의 PZT(Lead Zirconate Titanate) 분말을 수열합성법으로 제조하였으며 합성된 분말을 이용하여 소결특성을 조사하였다. 출발물질에 관계없이 입방체 형태를 갖는 PZT 결정분말이 형성되었으나 $Pb(NO_3)_2$, $Ti(OC_4H_9)_4$와 $Zr(OC_4H_9)_4$을 출발물질로 사용한 경우 다른 여러 출발물질을 사용한 경우보다 상대적으로 작은 입자가 생성되었다. 수열합성시 교반을 시키면서 합성한 경우 교반없이 반응시킨 경우에 비해 핵생성을 위한 수열 반응온도가 낮아졌으며 상대적으로 입경이 큰 입자들의 수가 늘어났다. Zr대Ti의 조성비를 변화시켜 수열합성한 반응물을 XRD 분석한 결과, 조성비가 40대60인 경우 정방정상이 주상(major phase)으로 형성되었으며 조성비가 60대40인 경우에는 주상의 결정형이 능면체정상으로 바뀌었다. 여러 조건에서 합성된 PZT 분말을 PbO 분위기에서 소결시키면서 소결온도 및 소결시간 변화에 따른 소결밀도의 변화를 분컥하였으며, $1150^{\circ}C$에서 2시간 소결시켰을 때 최적의 소결밀도, $7.6g/cm^3$을 갖는 소결체가 제조되었다.

• 한국재료학회지
• /
• 제22권9호
• /
• pp.489-493
• /
• 2012

Green phosphors $K_2BaW_2O_8:Tb^{3+}$(1.0 mol%) were synthesized by solid state reaction method. Differential thermal analysis was applied to trace the reaction processes. Three endothermic values of 95, 706, and $1055^{\circ}C$ correspond to the loss of absorbed water, the release of carbon dioxide, and the beginning of the melting point, respectively. The phase purity of the powders was examined using powder X-ray diffraction(XRD). Two strong excitation bands in the wavelength region of 200-310 nm were found to be due to the ${WO_4}^{2-}$ exciton transition and the 4f-5d transition of $Tb^{3+}$ in $K_2BaW_2O_8$. The excitation spectrum presents several lines in the range of 310-380 nm; these are assigned to the 4f-4f transitions of the $Tb^{3+}$ ion. The strong emission line at around 550 nm, due to the $^5D_4{\rightarrow}^7F_5$ transition, is observed together with weak lines of the $^5D_4{\rightarrow}^7F_J$(J = 3, 4, and 6) transitions. A broad emission band peaking at 530 nm is observed at 10 K, while it disappears at room temperature. The decay times of $Tb^{3+}$ $^5D_4{\rightarrow}^7F_5$ emission are estimated to be 4.8 and 1.4 ms, respectively, at 10 and 295 K; those of the ${WO_4}^{2-}$ exciton emissions are 22 and 0.92 ${\mu}s$ at 10 and 200 K, respectively.

• Tribology and Lubricants
• /
• 제15권1호
• /
• pp.77-82
• /
• 1999

The processing conditions fur the synthesis of platelet W $S_2$ lubricant powder through a solid-gas reaction were optimized. The mixture of tungsten and sulfur powders were sealed in a vacuum of 10$^{-6}$ torr, prior to heat-treating at 85$0^{\circ}C$ fur 8 days. The reaction product showed a well-developed platelet W $S_2$ powder with an average size of 3.8 ${\mu}{\textrm}{m}$. The TGA/DTA analysis of the synthesized W $S_2$ powder was performed up to 120$0^{\circ}C$ at a rate of 1$0^{\circ}C$/min in flowing air (100 ${\mu}{\textrm}{m}$/min) atmosphere. The weight loss was about 6% up to 120$0^{\circ}C$ compared to the original weight. A rapid weight loss of about 5% occurred in the temperature range of 44$0^{\circ}C$ to 66$0^{\circ}C$ and an exothermic peak observed due to the transition of W $S_2$ to W $O_3$. The synthesized W $S_2$powder was coated on the commercial deep grooved ball bearing (No. 6203) to examine the effect of W $S_2$, coating layer on the noise and endurance of the ball bearing. The level of noise obtained from W $S_2$, coated-ball bearing (56 ㏈) was higher. than the value (32 ㏈) occurred in the case of greece lubrication. The endurance of the ball-bearing assembled after the coating of W $S_2$ powder onto each part increased 50 times compared to the non-coated ball-bearing..

• 한국재료학회지
• /
• 제16권3호
• /
• pp.173-177
• /
• 2006

Porous surfaced Ti implant compacts were fabricated by electro-discharging-sintering (EDS) of atomized spherical Ti powders. Powders of $50-100{\mu}m$ in diameter were vibratarily settled into a quarts tube and subject to a high voltage and high density current pulse in Ar atmosphere. Single pulse of 0.7 to 2.0 kJ/0.7 gpowder, from 150, 300, and $450{\mu}F$ capacitors was applied in less than $400{\mu}sec$ to produce twelve different porous-surfaced Ti implant compacts. The solid core formed in the center of the compact shows similar microstructure of cp Ti which was annealed and quenched in water. Hardness value at the solid core was much higher than that at the particle interface and particles in the porous layer, which can be attributed to both heat treatment and work hardening effects induced by EDS. Compression tests were made to evaluate the mechanical properties of the EDS compacts. The compressive yield strength was in a range of 12 to 304MPa which significantly depends on input energy. Selected porous-surfaced Ti-6Al-4V dental implant compacts with a solid core have much higher compressive strengths compared to the human teeth and sintered Ti dental implants fabricated by conventional sintering process.

• 한국기계가공학회지
• /
• 제16권2호
• /
• pp.108-113
• /
• 2017

The performance of refrigerant oil at the thrust bearing and at the journal bearing of a scroll compressor is a significant factor. This paper presents the friction and anti-wear characteristics of nano-fluid with a mixture of a refrigerant oil and nano powders. The particle size distribution and oxidation stability of nano powders prepared by the electrical explosion method were analyzed by TEM and BET. It was found that the nanoparticles showed a spherical morphology with sizes ranging of 40-60 nm and were covered with graphite layers of 2-4 nm. The thermal conductivity of POE oil was 0.1-0.5W/mk higher than that of POE oil. The coefficient of friction of Cu-POE was found to be 0.1 higher than that of Al2O3. The cooling capacity of the heat pump with nanofluid increased to 3.67%, and the performance was improved by 5.83%.

• 한국재료학회지
• /
• 제15권6호
• /
• pp.399-407
• /
• 2005

The effect of IN738 additive powder on microstructure and mechanical properties of the wide-gap region brazed with BNi-3 filler metal powder was investigated. The wide-gap brazing was conducted in a vacuum of $2\times10^{-5}torr\;at\;1200^{\circ}C$ with various powder mixing ratios of additive to filler powders. The microstructures of the wide-gap brazed region were analyzed by SEM and AES. The region brazed with only BNi-3 filler metal powder had a microstructure consisted of proeutectic, binary eutectic and ternary eutectic structure, while that brazed with a mixture of IN738 additive powder and BNi-3 filler metal powder had a microstructure consisted of IN738 additive powder, binary eutectic of $Ni_3B-Ni$ solid solution and (Cr, W)B. The fracture strength of the wide-gap brazed region was about 680 MPa regardless of the additive powder mixing ratios. Cracks were initiated at the (Cr, W)B and binary eutectic of $Ni_3B-Ni$ solid solution, and propagated through them in the wide-gap brazed region, which lowered the fracture strength of the region.

• 한국분말재료학회지
• /
• 제22권4호
• /
• pp.283-288
• /
• 2015

Two sintering methods of a pressureless sintering and a spark-plasma sintering are tested to densify the Fe-TiC composite powders which are fabricated by high-energy ball-milling. A powder mixture of Fe and TiC is prepared in a planetary ball mill at a rotation speed of 500 rpm for 1h. Pressureless sintering is performed at 1100, 1200 and $1300^{\circ}C$ for 1-3 hours in a tube furnace under flowing argon gas atmosphere. Spark-plasma sintering is carried out under the following condition: sintering temperature of $1050^{\circ}C$, soaking time of 10 min, sintering pressure of 50 MPa, heating rate of $50^{\circ}C$, and in a vacuum of 0.1 Pa. The curves of shrinkage and its derivative (shrinkage rate) are obtained from the data stored automatically during sintering process. The densification behaviors are investigated from the observation of fracture surface and cross-section of the sintered compacts. The pressureless-sintered powder compacts show incomplete densification with a relative denstiy of 86.1% after sintering at $1300^{\circ}C$ for 3h. Spark-plasma sintering at $1050^{\circ}C$ for 10 min exhibits nearly complete densification of 98.6% relative density under the sintering pressure of 50 MPa.

• Journal of Nutrition and Health
• /
• 제37권7호
• /
• pp.515-524
• /
• 2004

This study was performed to investigate effect of dried powders and ethanol extracts of garlic flesh and peel on lipid metabolism and antithrombogenic capacity in 16-month-old rats. Forty Sprague-Dawley male rats weighing 618.1$\pm$6.5 g were blocked into five groups according to body weight and raised for 3 months with control and experimental diets containing 5% (w/w) of dried powders of garlic flesh or peel, or ethanol extracts from equal amount of each dried powder and control diet. Plasma and liver total lipids, triglyceride and total cholesterol, and plasma HDL-cholesterol, throm-boxane $B_2$ (TX $B_2$), 6-keto-prostaglandin $F_{1a}$ (6-keto-PG $F_{1a}$) concentrations were measured. Total, insoluble and soluble dietary fibers contents were highest in peel powder followed by fresh powder, and those in ethanol extracts of flesh and peel, especially soluble, very low. Plasma and liver total lipids, triglyceride, and total cholesterol concentrations were lower in all the garlic experimental groups compared to Especially, flesh and peel powder lowered plasma total lipids, triglyceride and total cholesterol concentrations markedly, and flesh powder and flesh ethanol extract lowered liver total lipids, triglyceride and total cholesterol concentration remarkably. Plasma TX $B_2$ concentrations in garlic experimental groups were lower than that of control group, and 6-keto-PG $F_{1a}$ concentrations. In garlic experimental groups were higher than that of control group. Flesh ethanol extract group showed the lowest TX $B_2$ and the highest 6-keto-PG $F_{1a}$ concentrations among experimental groups, so TX $B_2$/6-keto-PG $F_{1a}$ ratio in flesh ethanol extract group was significantly lower than that of control group. Moreover, clotting time was significantly increased in flesh ethanol extract group as compared to control group. In conclusion, intakes of dried powders and ethanol extracts of garlic flesh and peel were effective in lowering lipid levels of liver and plasma. And also flesh ethanol extract diet was most effective in antithrombogenic activity among garlic experimental groups as TX $B_2$/6-keto-PG $F_{1a}$ ratio in flesh ethanol extract group was significantly lower and clotting time was significantly increased in this group as compared to control group.ntrol group.