• ETRI Journal
• /
• 제30권3호
• /
• pp.383-393
• /
• 2008

The etching mechanism of $ZrO_2$ thin films and etch selectivity over some materials in both $BCl_3$/Ar and $BCl_3/CHF_3$/Ar plasmas are investigated using a combination of experimental and modeling methods. To obtain the data on plasma composition and fluxes of active species, global (0-dimensional) plasma models are developed with Langmuir probe diagnostics data. In $BCl_3$/Ar plasma, changes in gas mixing ratio result in non-linear changes of both densities and fluxes for Cl, $BCl_2$, and ${BCl_2}^+$. In this work, it is shown that the non-monotonic behavior of the $ZrO_2$ etch rate as a function of the $BCl_3$/Ar mixing ratio could be related to the ion-assisted etch mechanism and the ion-flux-limited etch regime. The addition of up to 33% $CHF_3$ to the $BCl_3$-rich $BCl_3$Ar plasma does not influence the $ZrO_2$ etch rate, but it non-monotonically changes the etch rates of both Si and $SiO_2$. The last effect can probably be associated with the corresponding behavior of the F atom density.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제17권4호
• /
• pp.483-491
• /
• 2017

The interdigitated germanium (Ge) meta-lsemiconductor-metal (MSM) photodetectors (PDs) with and without an $SiO_2$ anti-reflection (AR) layer was fabricated, and the effect of $SiO_2$ AR layer on their optoelectronic response properties were investigated in detail. The lowest reflectance of 15.6% at the wavelength of 1550 nm was obtained with a $SiO_2$ AR layer with a thickness of 260 nm, which was in a good agreement with theoretically calculated film thickness for minimizing the reflection of Ge surface. The Ge MSM PD with 260 nm-thick $SiO_2$ AR layer exhibited enhanced device performance with the maximum values of responsivity of 0.65 A/W, the quantum efficiency of 52.2%, and the detectivity of $2.49{\times}10^9cm\;Hz^{0.5}W^{-1}$ under the light illumination with a wavelength of 1550 nm. Moreover, time-dependent switching analysis of Ge MSM PD with 260 nm- thick $SiO_2$ AR layer showed highest on/off ratio with excellent stability and reproducibility. All this investigation implies that 260 nm-thick $SiO_2$ AR layer, which is effective in the reduction in the reflection of Ge surface, has a great potential for Ge based optoelectronic devices.

• 한국진공학회지
• /
• 제19권3호
• /
• pp.177-183
• /
• 2010

우리는 MOCVD (metal organic chemical vapor deposition)법을 이용하여 DEZ (Diethylzinc)을 운송하는 Ar 유속과 reactant (반응물질)의 종류에 따른 ZnO 박막 증착을 연구하였다. Bubbler 시스템을 통하여 주입되는 Ar 유속에 의해 Zn 소스인 DEZ의 양이 조절된다. 산소 기체와 수증기는 산화를 위해 반응물질로 사용된다. 본 연구로부터 표면의 거칠기(surface roughness)는 반응물질의 종류와 DEZ Ar 유속에 관계되며 박막의 두께에 의존한다는 것을 알 수 있었다. 그러나 기판 온도는 산소를 반응물로 하는 상태에서는 표면 거칠기에 영향을 주지 못함을 알 수 있었다. 우리는 ZnO 박막이 90 sccm (Standard Cubic Centimeter per Minute)의 DEZ Ar 유속, 8 Pa의 수증기압, 그리고 $140^{\circ}C$의 기판 온도에서 39.16 mm의 가장 높은 거칠기를 가진다는 것을 확인할 수 있었다. 본 논문은 태양전지의 광 흡수층으로 사용가능한 ZnO 박막을 연구하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제11권2호
• /
• pp.1-6
• /
• 2009

We report a successful fabrication of $high-J_c\;NdBa_2Cu_3O_{7-{\delta}}$ (NdBCO) films on $SrTiO_3$(STO) (100) substrates by pulsed laser deposition (PLD) in a relatively wide processing window. Under various oxygen pressures controlled by either 1%$O_2$/Ar mixture gas or pure $O_2$ gas, strongly c-axis oriented NdBCO films were grown at the substrate temperature $(T_s)\;of\;800^{\circ}C$ in 800 mTorr with 1%$O_2$/Ar gas and also in 400 and 800 mTorr with pure $O_2$ gas. These samples exhibited $T_c$ values over 90K and $J_c$ values of $2.8-3.5MA/cm^2$ at 77K in self-field (77K, sf). On the other hand, $J_c$ values over $1A/cm^2$ were obtained at the temperature regions of $700-830^{\circ}C$ in 800 mTorr with 1%$O_2$/Ar gas at those of $750-830^{\circ}C$ in 800 mTorr with pure $O_2$ gas. Unlike previous reports, resent results support that the PLD processing window for high-Jc NdBCO films is not narrow.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.72-74
• /
• 2004

In this study, we used a inductively coupled plasma (ICP) source for etching $Al_2O_3$ thin films because of its high plasma density, low process pressure and easy control bias power. $Al_2O_3$ thin films were etched using $Cl_2/BCl_3$, $N_2/Cl_2/BCl_3$, and Ar/$Cl_2/BCl_3$ plasma. The experiments were carried out measuring the etch rates and the selectivities of $Al_2O_3$ to $SiO_2$ as a function of gas mixing ratio, rf power, and chamber pressure. When $Cl_2$ 50% was added to $Cl_2/BCl_3$ plasma, the etch rate of the $Al_2O_3$ films was 118 nm/min. We also investigated the effect of gas addition. In case of $N_2$ addition, the etch rate of the $Al_2O_3$ films decreased while $N_2$ was added into $Cl_2/BCl_3$ plasma. However, the etch rate increased slightly as Ar added into $Cl_2/BCl_3$ plasma, and then further increase of Ar decreased the etch rate. The maximum etch rate was 130 nm/min at Ar 20% in $Cl_2/BCl_3$ plasma, and the highest etch selectivity was 0.81 in $N_2$ 20% in $Cl_2/BCl_3$ plasma. And, we obtained the results that the etch rate increases as rf power increases and chamber pressure decreases. The characteristics of the plasmas were estimated using optical emission spectroscopy (OES).

• Bulletin of the Korean Chemical Society
• /
• 제25권2호
• /
• pp.226-232
• /
• 2004

Ground and low-lying electronic states of Cr atoms in the gas phase were generated from photolysis of $Cr(CO)_6$ vapor in He or Ar using an unfocussed weak UV laser pulse and their reactions with $O_2$ and $N_2O$ were studied. When 0.5-1.0 Torr of $Cr(CO)_6$ /$O_2$ /He or Ar mixtures were photolyzed using 295-300 nm laser pulses, broadband chemiluminescence peaked at ~420 and ~500 nm, respectively, was observed in addition to the atomic emissions from $z^7P^{\circ}$, $z^5P^{\circ}$, and $y^7P^{\circ}$ states of Cr atoms. When $N_2O$ was used instead of $O_2$, no chemiluminescence was observed. The chemiluminescence intensities as well as the LIF intensities for those three low-lying electronic states ($a^7S_3,\;a^5S_2\;and\;a^5D_J$) showed second-order dependence on the photolysis laser power. Also, the chemiluminescence intensities were first-order in $O_2$ pressure, but the presence of excess Ar showed a strong inhibition effect on them. Based on the experimental results, the chemiluminecent species in this work is attributed to $CrO_2^*$ generated from hot ground state Cr atoms with $O_2$. The apparent radiative lifetimes of the chemiluminescent species and collisional quenching rate constants by $O_2$ and Ar also were investigated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1211-1214
• /
• 2005

One of the important problems in recent AC-PDP technology is high efficiency. In this research, we have been investigated electro-optical characteristics of MgO protective layer after radio frequency(RF) plasma treatment using Ar, $O_2$, and $H_2$ gases. The breakdown voltage order was $O_2$ > Ar > Nontreatment > $H_2$. Also, brightness order was $O_2$ > Ar > Non-treatment > $H_2$. In this experiment, the best result was obtained after $O_2-plasma$ treatment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.117-119
• /
• 2003

The $Pb(Zr_{0.3}Ti_{0.7)O_3/Pb(Zr_{0.7}/Ti_{0.3})O_3$ [PZT(30/70)/(70/30)] heterolayered thin films were deposited by RF sputtering method on the $Pt/TiO_2/SiO_2/Si$ substrate. Sputter gas ratio(AR/O2) was changed form 90/10 to 50/50. The structural properties and electrical properties of the PZT(30/70)/ (70/30) heterolayered thin films were studied. The relative dielectric constant and dielectric loss at 100Hz of the PZT(30/70)/PZT(70/30) heterolayered thin films with Ar/$O_2$(80/20) ratio were about 982 and 0.036, respectively.

• Transactions on Electrical and Electronic Materials
• /
• 제16권6호
• /
• pp.346-350
• /
• 2015

In this study, we carried out an investigation of the etch characteristics of TiO₂ thin films and the selectivity of TiO₂ to SiO₂ in adaptive coupled C1₂/Ar plasma. The maximum etch rate of the TiO₂ thin film was 136±5 nm/min at a gas mixing ratio of C1₂/Ar (75%:25%). The X-ray photoelectron spectroscopy (XPS) analysis showed the efficient destruction of oxide bonds by the ion bombardment as well as the accumulation of low volatile reaction products on the etched surface.

• 한국표면공학회지
• /
• 제54권2호
• /
• pp.43-52
• /
• 2021

The Ni-based superalloy, Inconel 740, was corroded between 800 and 1100℃ for up to 100 hr in air and Ar-0.2%SO₂ gas in order to study its corrosion behavior in air and sulfur/oxygen environment. It displayed relatively good corrosion resistance in both environment, because its corrosion was primarily dominated by not sulfidation but oxidation especially in Ar-0.2%SO₂ gas. Such was attributed to the thermodynamic stability of oxides of alloying elements when compared to corresponding sulfides. The scales consisted primarily of Cr₂O₃, together with some NiAl₂O₄, MnCr₂O₄, NiCrMnO₄, and rutile-TiO₂. Sulfur from SO₂ gas made scales prone to spallation, and thicker. It also widened the internal corrosion zone when compared to air. The corrosion resistance of IN740 was mainly indebted to the formation of protective Cr₂O₃-rich oxides, and suppression of the sulfide formation.