• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.348-355
• /
• 2023

Magnesium secondary batteries are attracting much attention due to their potential to replace conventionally used lithium ion batteries. Magnesium secondary battery cathode material Mo₆S₈ were synthesized by molten salt synthesis method and PVC as a carbon materials were added to improve electrochemical properties. Crystal structure, size and surface of the synthesized anode materials were measured through XRD and SEM. Charge-discharge profiles and rate capabilities were measured by battery test system. 2.81 wt% PVC coated sample showed the best rate capabilities of 85.8 mAh/g at 0.125 C-rate, 69.2 mAh/g at 0.5 C-rate, and 60.5 mAh/g at 1 C-rate.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.851-856
• /
• 2002

Tribological behavior of plasma-sprayed $Cr_2O_3$-based coatings containing $MoO_3$ at 450$^{\circ}C$ was investigated to understand the influence of $MoO_3$. A reciprocal disc-on-plate type tribo-tester was employed to examine fricition and wear behavior of the specimens. The microstructure and phase composition of the coating was characterized with Transmission Electron Microscopy(TEM). The TEM analysis indicated that $MoO_3$ was dispersed into the grain boundary, resulting in the increase of the hardness and density of the coating. Worn surfaces were investigated by scanning electron microscopy and chemistry of the worn surfaces was analyzed using a X-ray Photoelectron Spectrometer(XPS). The results showed that the friction coefficient of the $MoO_3$-added coatings was lower than that without $MoO_3$ addition. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with $MoO_3$ composition in the protecting layer appears to be more favorable in reducing the friction.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.6 s.171
• /
• pp.159-167
• /
• 2005

This work focuses on the effects of crack free friction on Mode II stress intensity factors, $K_{II}$, for a vertical surface crack in a two-dimensional finite element model of TiN/steel subject to rolling contact. Results indicate that maximum $K_{II}$ values, which occur when the load is adjacent to the crack, may be significantly reduced in the presence of crack face friction. The reduction is more significant for thick coatings than for thin. Crack extension and increased layer thickness result in increased $K_{II}$ values. The effect of crack face friction on compressive $K_I$ values appears negligible. Comparative results are presented for $MoS_2/steel$ and diamond-like carbon(DLC)/Ti systems.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.145-146
• /
• 2015

초미세 가공 및 치수안정성 향상을 위한 다이아몬드 마이크로 블레이드의 DLC 코팅이 연삭 과정에서 결합구조가 안정적으로 유지되는지 알아보기 위해 Cu/Sn 금속 결합재에 $MoS_2$ 고체 윤활제를 첨가한 후 PAPVD법으로 DLC 박막을 블레이드의 측면에 증착하였다. 실착 절삭 시험을 위해 마이크로 블레이드 시편을 제조하여 충분한 드레싱 과정 후 절삭 시험을 행하였으며 라만 분광법을 통해 절삭 전후 DLC 코팅에 존재하는 $sp^2$, $sp^3$ 결합의 분율을 조사하고 그 결과를 토대로 DLC 코팅의 특성의 변화를 분석하였다. DLC 코팅에 존재하는 D밴드와 G밴드의 비인 ID/IG는 절삭 후 증가하는 경향을 보였으며 결과적으로 절삭 과정 중 흑연화가 진행되었음을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.347.2-347.2
• /
• 2016

Recently, in order to improve the performance of the colloidal quantum dot solar cells (CQDSCs), various efforts such as the modification of the cell architecture and surface treatment for quantum dot (QD) passivation have been made. Especially, the incorporation of halides into the QD matrix was reported to improve the performances significantly via passivating QD trap states that lower the life-time of the minority-carrier. In this work, we fabricated a lead sulfide (PbS) QD bilayer treated with different ligands and utilized it as a photoactive layer of the CQDSCs. The bottom and top PbS layer was treated using metal iodide ($MI_x$ and butanedithiol (BuDT), respectively. All the depositions and ligand treatments were carried out in air using layer-by-layer spin-coating process. The fabrication of the active layers as well as the n-type zinc oxide (ZnO) layer was successfully carried out on the bendable indium-tin-oxide (ITO)-coated polyethylene terephthalate (PET) substrate, which implies that this technique can be applied to the fabrication of flexible and/or wearable solar cells. The power conversion efficiency (PCE) of the CQDSCs with the architecture of $PET/ITO/ZnO/PbS-MI_x/PbS-BuDT/MoO_x/Ag$ reached 4.2 %, which is significantly larger than that of the cells with single QD (PbS-BuDT) layer.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.3
• /
• pp.335-343
• /
• 2019

In this study, $Sr_2Ni_{1.8}Mo_{0.2}O_{6-{\delta}}$ (SNM) with a double perovskite structure was investigated as an alternative anode for use in the $CH_4$ fuel in solid oxide fuel cells. SNM demonstrates a double perovskite phase over $600^{\circ}C$ and marginal crystallization at higher temperatures. The Ni nanoparticles were exsolved from the SNM anode during the fabrication process. As the SNM anode demonstrates poor electrochemical and electro-catalytic properties in the $H_2$ and $CH_4$ fuels, it was modified by applying a samarium-doped ceria (SDC) coating on its surface to improve the cell performance. As a result of this SDC modification, the cell performance improved from $39.4mW/cm^2$ to $117.7mW/cm^2$ in $H_2$ and from $15.9mW/cm^2$ to $66.6mW/cm^2$ in $CH_4$ at $850^{\circ}C$. The mixed ionic and electronic conductive property of the SDC provided electrochemical oxidation sites that are beyond the triple boundary phase sites in the SNM anode. In addition, the carbon deposition on the SDC thin layer was minimized due to the SDC's excellent oxygen ion conductivity.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.3-4
• /
• 1999

최근 산업이 고속도화, 고능률화 및 고정멸화의 추세로 발전함에 따라 우수한 내마모성, 인성, 고온 안정성 및 내구성을 갖는 공구 및 금형을 요구하게 되었다. 그러나 이와같은 성질들은 어떤 단일 재료에서는 얻을 수 없으며 적당한 기판공구나 금혈위에 내마모성 보호피막을 coating함으로 비교적 저렴하게 얻을 수 있다. 화학증착법으로 TiC, TiN등을 증착시킬때에는 $1000^{\circ}C$정도의 반응온도가 필요하며 이러한 증착온도는 모재가 초경합금일때는 문제가 안되나 강재일 경우 모재의 연화와 칫수변화의 문제를 야기시킨다. 최근에는 플라즈마를 사용하여 증착반응온도를 $550^{\circ}C$ 이하로 낮추는 플라즈마 화학 증착볍(PACVD)이 대두되고 있다. 그러나 이 방법어서 는 뚱착하려는 금속원소가 TiCl4의 형태로 공급되고 있으므로 생성된 층이 염소를 포함하고 있다. 이 층에 잔존하는 염소는 층의 기계적 성질을 저하시키고 층내의 stress를 유발시킨다. 또한 HCI개스의 생성으로 인하여 펌프 및 장비의 부식이 촉진 된다 이러한 결점을 극복하기 위하여 금속유기화합물 전구체(metallo-organic precursor)로 $TiCl_4$를 대체하고자 하는 연구가 활발하게 진행되고 있으며 본 연구실에서 이에 대하여 연구한 결과를 소개하고자 한다. diethylamino titanium을 전구체로 사용하여 $H_2,\;N_2,\;Ar$분위기하에서 pulsed d.c.를 사용하는 MO-PACVD에 의하여 $150~250^{\circ}C$의 저온에서 Al 2024 기판에 TiCN층 형 성을 하였다. 전구체 증발온도는 $74~78^{\circ}C$의 온도범위어야 하며 고경도의 코탱층은 54% duty, 14.2kHz, 450V의 조건에서 얻어졌으며 duty, 주파수, 전압이 증가함에 따라 경도는 저하되었다. 이때의 표면 morphology를 SEM으로 조사한바 dome structure가 크게 발달되었음을 알 수 있었다. 본 실험의 온도 범위내에서 얻은 TiCN 증착반응의 활성화에너지는 7.5Kcal/mol이었다. 증착된 TiCN층은 우수한 내마모섣을 나타내었으며 스크래치테스트 결과 17N의 엄계하중을 나타내었다. 본 연구에서 변화 시킨 duty, 주파수, 전압의 범위에서는 층의 밀착력은 크게 변화하지 않았다. titanium isopropoxide를 전구체로 사용하여 Hz, Nz 분위기하에서 d.c.를 사용하는 MO-PACVD에 의하여 Ti(NCO) 코팅층을 SKDll, SKD61, SKH9 공구강에 형성시키는 공정을 개발하였다. 최적의 Ti(NCO) 코탱층을 얻기 위해 유입전구체 부피%의 양은 향착압력의 5%를 넘지 않아야 되고 수소와 젤소 가스비가 1:1일 때 가장 높은 코팅층의 경도값을 나타내었다. 수소와 질소 가스비가 3:7일 때 TiFeCr(NCO)의 복화합물 코팅층이 형성됨을 알 수 있었고 500t의 증착온도에서 얻은 Ti(NCO) 코팅층이 높은 경도값과 좋은 내식성을 나타내었다. 또한 이와같은 Ti(NCO) 코팅공정과 본 실험실에서 개발한 확산층만 형성시키는 plsma nitriding 공정을 결합하여 복합코탱층을 형성하였는데 이 복합코팅층은 고경도와 우수한 내마모성, 내식성 뿐만 아니라 10)N 이상의 뛰어난 밀착력을 나타내었다. 현재 많이 사용되고 있는 PVD법은 step coverage가 좋지 않은 점과 cost intensive p process라는 단점이 있다. MO-PACVD법은 이러한 문제를 해결할 수 있는 방법으로서 앞으로 지속적인 도전이 요구되는 분야이다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.305-306
• /
• 2006

Ga-doped and Al-doped ZnO thin films were fabricated via a sol-gel technique and electrical and optical properties of the films were investigated. Film deposition was performed by spin coating at 4000 rpm for 30 s on $SiO_2$ glass substrate FE-SEM was used to obtain the surface morphology images and the film thickness Four-point probe and UV-VIS spectrophotometer were used to measure the sheet resistance and the optical transparency, respectively.

• Journal of Biomedical Engineering Research
• /
• v.25 no.2
• /
• pp.157-163
• /
• 2004

Nitrogen ion implantation and ion plating techniques were applied for improvement of the wear resistance of metallic implant materials. In this work, the wear dissolution behaviour of a nitrogen ion implanted super stainless steel (S.S.S, 22Cr-20Ni-6Mo-0.25N) was compared with those of S.S.S, 316L SS and TiN coated 316L SS. The amounts of Cr and Ni ions worn-out from the specimens were Investigated using an electrothermal atomic absorption spectrometry. Furthermore, the Ti(Grade 2) disks were coated with TiN, ZrN and TiCN by use of low temperature arc vapor deposition and the wear resistance of the coating layers was compared with that of titanium. The chemical compositions of the nitrogen ion implanted and nitride coated layers were examined with a scanting auger electron spectroscopy. It wat observed that the metal ions released from the nitrogen ion implanted S.S.S surface were significantly reduced. From the results obtained, it was shown that the nitrogen ion implanted zone obtained with 100 KeV ion energy was easily removed within 200,000 revolutions from a wear dissolution testing under a similar load condition when applied to artificial hip joint. The remarkable improvement in wear resistance weir confirmed by the nitrides coated Ti materials and the wear properties differ greatly according to the chemical composition of the coating layers. for specimens with the same coating thickness of about 3$\mu\textrm{m}$, TiCN coated Ti showed the highest wear resistance. However, after removing the coating layers, the wear rates of all nitrides coated Ti reverted to their normal rates of below 10,000 revolutions from Ti-disk-on-disk wear testing under the same load condition. From the results obtained, it is suggested that the insufficient depth of the 100 Kel N$\^$＋/ ion implanted zone and of the nitrides coated layers of 3$\mu\textrm{m}$ are subject to restriction when used as frictional parts of load bearing implants.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.638-646
• /
• 2023

Recently, active research has been conducted to enhance the power characteristics and thermal stability of lithium-ion batteries (LiBs) by modifying separators using a ceramic coating method. However, since the thermal properties and surface features of the separator vary depending on the characteristics of the ceramic powders applied to the separator, it is crucial to manufacture ceramic powders optimized for the separator's performance. In this study, we evaluated the characteristics of three types of α-alumina (A-1, A-2, and A-3) produced with varying dispersant contents and milling times, in addition to commercial α-alumina (AES-11). Subsequently, the optimized powders (A-3) were coated onto the separator using an aqueous binder for comparison with the characteristics of an AES-11 coated separator and an uncoated PE separator. The A-3 coated separator improved electrolyte wettability with a low contact angle (44.69°) and increased puncture strength (538 gf). Furthermore, it exhibited excellent thermal stability, with a shrinkage value of 5.64% when exposed to 140℃ for 1 hour, compared to the AES11 coated separator (6.09%) and the bare PE separator (69.64%).