• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.2
• /
• pp.5-12
• /
• 2000

Uncooled metallic thin-film thermopile infrared detectors have been fabricated, and the figures of merit for the detectors were examined. The hot junctions of a thermopile were prepared on a $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$-membrane which acts as a thermal isolation layer, the cold junctions on the membrane supported with the silicon rim which functions as a heat sink, and Au-black was used as an infrared absorber. Infrared absorbance of Au-black, which strongly depends on the chamber pressure during Au-evaporation and its mass per area, was found to be about 90 ％ in the wavelength range from 3${\mu}{\textrm}{m}$ to 14${\mu}{\textrm}{m}$. Voltage responsivity, noise equivalent power, and specific detectivity of Bi-Sb thermopile infrared detector at 5 Hz-chopping frequency were about 10.5V/W, 2.3 nW/Hz$^{1/2}$, 및 $1.9\times10^{7}$ cm.Hz$^{1/2}$/w at room temperature in air, respectively.

• Membrane Journal
• /
• v.30 no.5
• /
• pp.319-325
• /
• 2020

In this study, we developed mixed matrix membranes by blending thermoplastic elastomer, i.e. polystyreneblock-polybutadiene-block-polystyrene (SBS) block copolymer with the synthesized UiO-66 particles for CO₂/N₂ gas separation. To investigate the effect of UiO-66 particles in the SBS matrix, we prepared different mixed matrix membranes (MMMs) by varying the mass ratio of SBS and UiO-66 in the blend. To fabricate well-dispersed UiO-66, the SBS/UiO-66 mixture was sonicated and stirred thoroughly. The physico-chemical properties of prepared membranes were characterized by Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscope (SEM). The gas separation performance was measured by time-lag method. The permeability of the MMMs increased significantly as the content of UiO-66 increased, but the CO₂/N₂ selectivity did not decrease significantly. The membranes containing 20% of UiO-66 particles showed the best performance with the CO₂ permeability and CO₂/N₂ selectivity of 663.8 barrer and 13.3, respectively. This result showed performance closer to upper bound than pure SBS membrane in the Robeson plot, as the added UiO-66 particles did not significantly sacrifice selectivity and more than doubled gas permeability.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.11
• /
• pp.1355-1363
• /
• 2009

In the present study, the neuroprotective effects of astaxanthin on $H_2O_2$-mediated apoptotic cell death, using cultured mouse neural progenitor cells (mNPCs), were investigated. To cause apoptotic cell death, mNPCs were pretreated with astaxanthin for 8 h and followed by treatment of 0.3 mM $H_2O_2$. Pretreatment of mNPCs with astaxanthin significantly inhibited $H_2O_2$-mediated apoptosis and induced cell growth in a dose-dependent manner. In Western blot analysis, astaxanthin-pretreated cells showed the activation of p-Akt, p-MEK, p-ERK, and Bcl-2, and the reduction of p-P38, p-SAPK/JNK, Bax, p-GSK3b, cytochrome c, caspase-3, and PARP. Because $H_2O_2$ triggers caspases activation, this study examined whether astaxanthin can inhibit caspases activation in $H_2O_2$-treated mNPCs. After $H_2O_2$ treatment, caspases activities were prominently increased, but astaxanthin pretreatment significantly inhibited $H_2O_2$-mediated caspases activation. Astaxanthin pretreatment also significantly recovered the ATP production ability of $H_2O_2$-treated cells. These findings indicate that astaxanthin inhibits $H_2O_2$-mediated apoptotic features in mNPCs. Inhibition assays with SB203580 ($10\;{\mu}M$, a specific inhibitor of p38) and PD98059 ($10\;{\mu}M$, a specific inhibitor of MEK) clearly showed that astaxanthin can inhibit $H_2O_2$-mediated apoptotic death via modulation of p38 and MEK signaling pathways.

• Textile Coloration and Finishing
• /
• v.33 no.3
• /
• pp.97-104
• /
• 2021

In this study, the dyeability of m-aramid fabric with various cationic dyes using two bath two step dyeing method were investigated. The exhaustion properties of Doracryl series recommend for aramid(Doracryl^® Red GL 100%(DR), Doracryl^® Blue GL 300%(DB), Doracryl^® Yellow XGRL 200%(DY)) and commercial cationic Synocryl series(Synocryl^® Red GRL ED(SR), Synocryl^® Blue GSL ED(SB), Synocryl^® Yellow 3RL ED(SY)) for acrylic were measured by using Dye-O-meter. In the presence of carrier, the exhaustions of Doracryl series were higher to those of Synocryl series and the opposite phenomenon was observed in the absence of carrier. And the severe migrations of cationic dyes to acetate, nylon and wool fabrics were observed without carrier.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.10
• /
• pp.458-463
• /
• 2003

In order to develope piezoelectric transformer for the ballast of fluorescent lamp, a new shape and electrode pattern of piezoelectric transformer has been investigated in this work. The composition of piezoelectric ceramics was 0.95Pb(Zr$_{0.51}$Ti$_{0.49}$)O$_3$+0.03Pb(Mn$_{1}$3/Nb$_{2}$3/)O$_3$+0.02Pb(Sb$_{1}$2/Nb$_{1}$2/)O$_3$. The sample prepared by this composition system showed the characteristics which has about 1200 of relative dielecric constant, 1100 of the mechanical quality factor, 0.53 of the electromechanical coupling coefficient, 320 pC/N of the piezoelectric constant d$_{33}$, 0.3 % of the dissipation factor. Diameter and thickness of disk-type piezoelectric transformer was 45 mm and 4 mm, respectively. The driving and generating electrode with their gap of 1mm were fabricated on the top surface. But the common electrode was fabricated on the whole bottom surface. The electrode surface ratio of driving and generating part on the top surface ranges from 1.4:1 to 3:1. We investigated the electrical characteristics with the variation of the electrode surface ratio of driving and generating part in the range of load resistance of 100 $\Omega$～70 k$\Omega$. The set-up voltage ratio of this piezoelectric transformer increases with increasing both the electrode surface of driving part and the load resistance. The set-up voltage ratio at no load resistance was more than 60 times. On the other hand, the efficiency decreases with increasing the electrode surface of driving part. In the case of the electrode surface of both 1.4:1 and 2:1, maximum efficiency showed above 97 % at load resistance of 2 k$\Omega$. However, in the case of the electrode surface of 3:1, maximum efficiency showed about 94 % at load resistance of 3 k$\Omega$.>.>.>.

• Advances in Traditional Medicine
• /
• v.9 no.3
• /
• pp.252-258
• /
• 2009

Shade-dried flowers of Sarcostemma brevistigma Wight Syn (SBF) belonging to Asclepiadaceae yielded a rare flavonol glycoside viz., Quercetin 5a prenyl, 3-O-glucosyl, 7-O-(4c-p-coumaroyl) neohesperidoside which were characterized based on chemical and spectral (including 2D NMR) studies. The ethyl acetate fraction of alcoholic concentrate (test sample) of flowers of this plant (SBF) was evaluated for its hepatoprotective and inhibition of lipid peroxidation activities to investigate the scientific basis of the traditional uses. The oral administration in varying doses viz., 125 and 250 mg/kg of aqueous suspension of SBF to rats for 7 days produced significant (P < 0.01) hepatoprotective effect comparable to that of standard drug silymarin. The SBF afforded good hepatoprotection against $CCl_4$ induced elevation levels of serum marker enzymes, serum bilirubin and liver weight. The free radical scavenging effects of SBF and flavonol glycoside (SA) were assigned by $Fe^{2+}$/ascorbate induction method (in vitro), which revealed the inhibition of lipid peroxidation. The SBF and SA showed prominent anti-lipid peroxidation activity ($IC_{50}$ about $\sim$180 mg/ml and 11.0 mg/ml respectively), which was comparable to standard drug curcumin ($IC_{50}$ about $\sim$8.25 mg/ml). Thus the hepatoprotective activity of SB could be correlated to the free radical scavenging property of the flavonol glycoside.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.1
• /
• pp.27-32
• /
• 2001

The effect of $V_2O_5$, a donor-type dopant on the degradation of quality factor of ($Zr_{0.8}, Sn_{0.2})TiO_4$was compared with Ta$_2$O$_{5}$ doped ($Zr_{0.8}, Sn_{0.2})TiO_4$ in terms of microstructure, electrical conductivity, and oxidation state of the dopant. It is well known that the addition of the donor type species such as $Ta_2O_5,Nb_2O_5, Sb_2O_5, WO_{3}$, increases the quality factor of ($Zr_{0.8}, Sn_{0.2})TiO_4$due to decrease the oxygen vacancy concentration. Unlike other dopants, however, the addition of $V_2O_5$ decreased the quality factor. The degradation of quality factor of ($Zr_{0.8}, Sn_{0.2})TiO_4$was resulted from the formation of grain boundary phase and $V_2O_5$rich fiber shaped secondary phase, and the increasing the oxygen vacancy concentration due to unstability of oxidation state of vanadium ions in ($Zr_{0.8}, Sn_{0.2})TiO_4$ceramic.c.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.4
• /
• pp.338-343
• /
• 2002

In this study, $Pb_{0.88}(La_{\alpha}Nd_{1-\alpha})_{0.08}(Mn_{1/3}Sb_{2/3})_{0.02}Ti_{0.98}O_3$ system ceramics with La molar ratio $\alpha$ variation were manufactured for 24 MHz class resonator application. Electromechanical coupling factor, mechanical quality factor and dynamic range of $3^{rd}$ overtone thickness vibration mode were measured as the variations of La and Nd molar ratio. Mechanical quality factor and dynamic range at $\alpha$ = 0.6 composition ceramics showed the highest value of 2691 and 52.37 dB, respectively. The temperature coefficient of resonant frequency measured from $-20^{\circ} to 80^{\circ}$ showed an excellent value of $5ppm/^{\circ}C$ at $\alpha$=1 composition ceramics.

• Korean Journal of Materials Research
• /
• v.15 no.12
• /
• pp.814-817
• /
• 2005

In order to enhance energy efficiency in high electric conversion devices such as Power transformers, which need to have high power properties, an alloy design approach in $Pb(Zr,Ti)O_3(PZT)$ base ceramic system was attempted $0.03Pb(Sb_{0.5}Nb_{0.5})O_3-0.03Pb(Mn_{1/3}Nb_{2/3})O_3-(0.94-x)PbTiO_3-xPbZrO_3$[PSN-PMN- PZT] ceramics were synthesized by conventional bulk ceramic processing technique. To improve power properties, the various Zr/Ti ratio was varied ]lear their morphotropic phase boundary (MPB) composition of PSN-PMN-PZT system and their effects on subsequent piezoelectric and dielectric properties for the transformer application at high power were systematically investigated using an impedance analyzer. Microstructure and phase information were characterized using X-ray diffractometer (XRD), a scanning electron microscope (SEM) and others. When the Zr/Ti ratio was 0.415/0.465, the value of $Q_m\;and\;k_p$ were shown to reach to the maximum, indicating that this alloy design can be a feasible composition :or high power transformer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.5
• /
• pp.361-365
• /
• 2012

A bolt-clamped ultrasonic viscometer was designed and fabricated using a pair of ring-shaped piezoelectric ceramic resonators. For its compactness and low operation frequencies, simulation of piezoelectric resonators was carried out using an ATILA program. Ring-shaped resonators using $0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.95Pb(Zr_{0.475}Ti_{0.525})O_3$ ceramics were prepared by a conventional ceramic processing, which were then clamped with a pair of metal caps. The fabricated sensor module with a small volume of less than 1 $cm^3$ and an operation frequency as low as 26.5 kHz showed a good relationship between its quality factor and the viscosity of oil.