• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.7B
• /
• pp.886-891
• /
• 2011

Multicast has been a key routing service for efficient data dissemination in underwater acoustic sensor networks. In sensor networks, there are several multicast routing protocol which reflects sensor network nature. However, existing routing scheme was not targeted at underwater acoustic sensor networks which is hard to provide battery continually. Therefore, a specialized routing algorithm is essential for acoustic sensor networks. In this paper, we propose angle aided multicast routing algorithm for decreasing routing computation complexity, including virtual Euclidean Steiner point. Simulation results show better performance than exist routing Position Based Multicast, Geographic Multicast Routing. such as low computation capability and limited power consumption.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.6B
• /
• pp.738-743
• /
• 2011

This paper considers the cost minimization issue for sensor network systems where sensor energy is supplied by remote energy sources wirelessly. Assuming symmetric structures of sensor nodes and energy sources, cost minimization problem is formulated, where the cost of sensor networks is represented as a function of sensor node density and energy source coverage. The optimal solution for the problem is provided and simulation results show that the proposal scheme achieves around 19% cost reduction in comparision to a conventional scheme.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.6
• /
• pp.263-270
• /
• 2008

The performance of an ultrasonic array sensor is determined by the properties of constituent materials and the effects of many structural parameters. In this study, with the finite element method, variation of the performances of an ultrasonic array sensor was analyzed in relation to its structural variables. Based on the analysis result, the structure of the ultrasonic array sensor was optimized to provide the highest sensitivity while satisfying such requirements as fractional bandwidth, center frequency and -20 dB pulse length. The optimization was carried out with the SQP-PD method for a target function composed of the ultrasonic array sensor performance. The optimized ultrasonic array sensor satisfied all the required specifications to be applicable to medical imaging diagnosis. The design technology in this paper can be utilized for other ultrasonic array sensors of a similar structure.

• The KIPS Transactions:PartB
• /
• v.17B no.1
• /
• pp.9-14
• /
• 2010

In this paper, we propose method of correlation coefficients between sensors by statistical analysis that selects optimal sensors in odor recognition system of selective multi-sensors. The proposed sensor decision method obtains odor data from Metal Oxide Semiconductor(MOS) sensor array and then, we decide optimal sensors based on correlation of obtained odors. First of all, we select total number of 16 sensors eliminated sensor of low response and low reaction rate response among similar sensors. We make up DB using 16 sensors from input odor and we select sensor of low correlation after calculated correlation coefficient of each sensor. Selected sensors eliminate similar sensors' response therefore proposed method are able to decide optimal sensors. We applied to floral scent recognition for performance evaluation of proposed sensors decision method. As a result, application of proposed method with floral scent recognition using correlation coefficient obtained recognition rate of 95.67% case of using 16 sensors while applied floral scent recognition system of proposed sensor decision method confirmed recognition rate of 94.67% using six sensors and 96% using only 8 sensors.

• Electrical & Electronic Materials
• /
• v.9 no.5
• /
• pp.455-462
• /
• 1996

Automobile Fuel Shortage Detecting Sensor, in this paper, was fabricated by using heat dissipation coefficient difference between gasoline and air condition the NTC thermistor of Mn-Ni Co system with the composition ratio of Mn$_{3}$O$_{4}$ : 9wt%, NiO : 28wt%, and CO$_{3}$O$_{4}$ : 61wt%. The condition of sensor operation is that, for turn-on characteristics, the time of arriving at 135mA must be less than 180 second when the DC voltage of 11V is applied in the air condition of -10.deg. C and that, for turn-off characteristics, the saturation current must be less than 60mA when the DC voltage of 15V is applied in the gasoline condition of 60.deg. C. It is known, from the experimental results, that the resistance range and B-constant for the Automobile Fuel Shortage Detecting Sensor with dimension of 5*3*0.9mm were 850-1150.ohm. and 1150-1250.deg. C, respectively and the resistance range and B-constant were agree with that of sensor operation condition. When Bi$_{2}$O$_{3}$ of 0-0.5wt% was added to Mn$_{3}$O$_{4}$ : 9wt%, NiO : 28wt%, and CO$_{3}$O$_{4}$ : 61wt% composition, the resistivity and B-value were 380-430(.ohm.-cm) and 1930 - 2030, respectively. Particularly, for Bi$_{3}$O$_{3}$ of 0.25-0.5wt%, the sintering density of over 90% and the operation characteristics necessary to Automobile Fuel Shortage Detecting Sensor were obtained. The difference of heat dissipation coefficient gasoline and air condition was 15 times.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.2
• /
• pp.145-152
• /
• 2010

Gait phase detection is important for evaluating the recovery of gait ability in patients with paralysis, and for determining the stimulation timing in FES walking. In this study, three different motion sensors(tilt sensor, gyrosensor and accelerometer) were used to detect gait events(heel strike, HS; toe off, TO) and they were compared one another to determine the most applicable sensor for gait phase detection. Motion sensors were attached on the shank and heel of subjects. Gait phases determined by the characteristics of each sensor's signal were compared with those from FVA. Gait phase detections using three different motion sensors were valid, since they all have reliabilities more than 95%, when compared with FVA. HS and TO were determined by both FVA and motion sensor signals, and the accuracy of detecting HS and TO with motion sensors were assessed by the time differences between FVA and motion sensors. Results show of that the tilt sensor and the gyrosensor could detect gait phase more accurately in normal subjects. Vertical acceleration from the accelerometer could detect HS most accurately in hemiplegic patient group A. The gyrosensor could detect HS and TO most accurately in hemiplegic patient group A and B. Valid error ranges of HS and TO were determined by 3.9 % and 13.6 % in normal subjects, respectively. The detection of TO from all sensor signals was valid in both patient group A and B. However, the vertical acceleration detected HS validly in patient group A and the gyrosensor detected HS validly in patient group B. We could determine the most applicable motion sensors to detect gait phases in hemiplegic patients. However, since hemiplegic patients have much different gait patterns one another, further experimental studies using various simple motion sensors would be required to determine gait events in pathologic gaits.

• Journal of Industrial Technology
• /
• v.27 no.B
• /
• pp.97-101
• /
• 2007

We have developed a Edge Position Controller (EPC) using a ultrasonic sensor and applied to a fabric machine as a web guide system. Hardware devices composed of a ultrasonic transmitter-receiver sensor module and microprocessor-based sensor signal processing system are developed to realize the proposed system. We evaluated the control characteristics of the EPC and the performance of the system was good enough to apply the actual system.

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.739-745
• /
• 2014

We have demonstrated a $Ti:LiNbO_3$ electro-optic electric-field sensor utilizing a $1{\times}2$ Y-fed balanced-bridge Mach-Zehnder interferometric (YBB-MZI) modulator, which uses a 3-dB directional coupler at the output and has two complementary output waveguides. A dc switching voltage of ~25 V and an extinction ratio of ~12.5 dB are observed at a wavelength of $1.3{\mu}m$. For a 20 dBm rf input power, the minimum detectable electric fields are ~8.21, 7.24, and ~13.3 V/m, corresponding to dynamic ranges of ~10, ~12, and ~7 dB at frequencies of 10, 30, and 50 MHz respectively. The sensors exhibit almost linear response for an applied electric-field intensity from 0.29 V/m to 29.8 V/m.

• Journal of Sensor Science and Technology
• /
• v.14 no.6
• /
• pp.402-408
• /
• 2005

This paper describes the optimal design of a multi-layered surface plasmon resonance sensors to meet various specifications and improve some physical parameters. Dip 3 dB bandwidth and depth were chosen as design parameters and the objective function was the norm of the difference between design parameters and target values. The design variables are thicknesses of each layer and to obtain the design parameters, the optical admittance method was employed. The (1+1) evolution strategy was employed as an optimization tool. By applying the proposed optimization procedure to a 3-layered sensor, the optimized design variables considerably improved the 3 dB bandwidth by 4.8 nm and the dip depth by 1.1 dB.

• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.145-150
• /
• 2011

In this paper, we designed a tunable microstrip patch antenna using RF MEMS switches. The design and simulation of the antenna were performed using a high frequency structure simulator(HFSS). The antenna was designed for use in the ISM band and either operates at 2.4 GHz or 5.7 GHz achieving -10 dB return-loss bandwidths of 20 MHz and 180 MHz, respectively. In order to obtain high efficiency and improve the ease of integration, a high resistivity silicon(HRS) wafer on a glass substrate was used for the antenna. The antenna achieved high gains: 8 dB at 5.7 GHz and 1 dB at 2.4 GHz. The RF MEMS DC contact switches were simulated and analyzed using ANSYS software.