SiC-C films were deposited with r. f. magnetron sputtering on substrates followed by argon ion bombardment. These films were then permeated by hydrogen gas under the pressure of $3.23\times10^{7}$ Pa for 3 hours at temperature of 500K or bombarded with hydrogen ion beam at 5 keV and a dose of $1\times10^{18}$ ions/$\textrm{cm}^2$. SIMS, AES and XPS were used to analyze hydrogen related species, chemical bonding states of C, Si as well as contamination oxygen due to hydrogen participation in the SiC-C films in order to study the different behaviors of hydrogen in carbon-carbide films due to different hydrogen introduction. Related mechanism about the effects of hydrogen on the element of the SiC-C films was discussed in this paper.

Solid-state reactions in Ni/Si multilayered films (MLF) with an overall stoichiometry of $Ni_2Si$, NiSi and $NiSi_2$, induced by ion-beam mixing (IBM) and thermal annealing, were studied by using spectroscopic ellipsometry and magneto-optical spectroscopy as well as x-ray diffraction (XRD). The mixing was performed with Ar+ ions of an energy of 80 keV and a dose of $1.5 x\times10^{16}$ $Ar^+$/$\textrm{cm}^2$. It was shown that the IBM induces structural changes in the Ni/Si MLF, which cannot be detected by XRD but are confidently recognized by the optical method. A thermal annealing at 673 K of the Ni/Si MLF with an overall stoichiometry of NiSi and $NiSi_2$ causes formation of the first η -NiSi phase. The first trace for $NiSi_2$ phase on the background of NiSi one was detected by XRD after an annealing at 1073 K while, according to the optical results, $NiSi_2$ turns out be the dominant phase for the annealed Ni/Si MLF with an overall stoichiometry of $NiSi_2$.

Coatings of hydroxyapatite (HA) and tricalcium phosphate/HA (TCP/HA) on titanium were fabricated by ion beam assisted deposition (IBAD). Significant effect of the Ca-P coatings on human Gingival Fibroblasts (HGFs) attachment and formation of type I collagen were found by using immunofluorescence microscope. TCP/HA and HA coatings exerted more HGFs attachment and collagen I formation. Comparing with HA coating, TCP/HA coating exhibited better responses during the late period of the tests. This investigation indicated that this surface modification method may enhance the biological seal at the cervical level of the titanium dental implants.

3-D photonic band-gap structures are fabricated from dielectric colloidal polystyrene beads through a centrifuge method. The fabricated photonic crystals exhibit opalescent colors under white light and show a clear diffraction peak dependent on the incident angle of the light beam. Also the scanning electron microscope image was taken to verify the face-centered cubic crystal structure. Bragg's law and Snell's law are employed to describe the position of angle resolved diffraction peaks. It was shown that the optically deduced effective refractive index and lattice constants were in good agreement with the crystal structure identified by scanning electron microscope.

We have studied magnetic and structural properties of ultrathin Ni films grown on PI(lII) surface using in situ surface magneto-optic Kerr effect and X-ray photoelectron spectroscopy. Perpendicular magnetic anisotropy was absent, and longitudinal Kerr signal was only detectable for Ni films thicker than 6 monolayers. Enhancement in longitudinal Kerr signal by 30% was achieved by post-annealing at temperatures below 800K, but upon annealing at 820K, surface alloy was formed. By using core-level binding-energy shifts, the composition was determined to be Ni 70 at. %.

Micro-arc discharge oxidation (MDO) is a cost-effective plasma electrolytic process which can be used to improve the wear and corrosion resistance of Al-alloy parts by forming a alumina coating on the component surface. However, the MDO coated Al-alloy components often exhibit relatively high friction coefficients and low wear resistance fitted with many counterface materials, additionally, the pitting corrosion for the MDO coated AI-alloy components, especially for a thinner alumina coating, often occurs in atmosphere circumstance due to the porous alumina coats. Therefore, a duplex treatment, combining a MDO coated ahumina thin layer with a TiN coating, prepared by magnetron sputtering (MS), has been investigated. The Vicker's microhardness, pin-on-disc, electrochemical measurement, salt spray, XRD and SEM tests were used to characterize and analyze the treated samples. The work demonstrates that the MDO/MS coated samples have a combination of a very low friction coefficient and good wear resistance as well as corrosion since the micro-holes on alumina coating are partly or fully covered by TiN material.

Both $LiNbO_3$ and $KTiOPO_4$ samples were implanted with 350 keY $H^+$ and $He^+$ ions at different doses ranging from $1 ${\times}$\times10^{16}$ to of $5 ${\times}$\times10^{16}$ ions/$\textrm{cm}^2$. Single and multi-energy implantations were performed at room temperature. Mono-mode or a few modes in both $LiNbO_3$ and $KTiOPO_4$ waveguides were observed. The effect of temperature on the refractive index profiles of $LiNbO_3$ and $KTiOPO_4$ waveguids was studied. The temperature covered from room temperature, $200^{\circ}C$, 194.5 K (dry ice) and 77K (liquid nitrogen). Different mechanisms are needed to interpret the observed behavior. A n, increased mono-mode $LiNbO_3$ waveguide was formed by multi-energy keV $He^+$ ions.

The electrooptic properties of the reflected light in a reflective mode, $45^{\circ}C$twisted nematic liquid crystal (TNLC) cell were investigated in the voltage regions near and away from the Freedericksz transition threshold. The measured reflectivity away from the threshold voltage ($V_th$) could not be described by the model which assurnes a constant tilt angle as well as a linearized distribution of twist angle across the cell, although the data are well fitted near $V_th$. We found that in the voltage region away from $V_th$, the model considering the distributions of the tilt angle and the twist angle should be applied for the calculation of the reflectivity. The director-axis distributions were obtained from the numerical integration of the Euler-Lagrange equation.

Field-domain dynamics and current self-oscillations are theoretically studied in quantum-well (QW) negative-effective-mass (NEM) $p^{+}pp^{+}$ diodes when the electric field is applied along the direction of the well. The origin of current self-oscillations is the formation and traveling of electric-field domains in the p-base. We have accurately considered the scattering contributions from carrier-impurity, carrier-acoustic phonon, and carrier-optic phonon. It's indicated that, both the applied bias and the doping concentration largely influence the current patterns and self-oscillating frequencies, which lie in the THz range for the NEM $p^{+}pp^{+}$ diode with a submicrometer p-base. The complicated field-domain dynamics is presented with the applied bias as the controlling parameter.

Ru interfacial layer was inserted into Mo-on-Si interface to enhance the extreme ultra-violet (EUV) reflective multilayer properties. The stacking status and optical properties are analyzed using cross-sectional transmission electron microscope (TEM), and reflectometer. About 1.5% of maximum reflectivity can be acquired as predicted in optical simulation, which is thought to be originated from the diffusion inhibition property. Phase defect correctability of the multilayer can be enhanced by the insertion of Ru barrier layer.

The modification of metal surface by ion implantation with MEVVA ion implanter and thin film deposition with filtered vacuum arc plasma device is introduced in this paper. The combination of ion implantation and thin film deposition is proved as a better method to improve properties of metal surface.

Amorphous hydrous ruthenium oxide thin films have attracted much interest owing to the possibility of using this material in electrochemical supercapacitors. Recently, it was found that this material is also electrochromic: during the charging/discharging cycle, the optical transmittance of the thin film is modulated. The physical and chemical origin of this phenomenon is not fully understood yet. In this work, we performed in-situ Raman spectroscopy measurements on amorphous hydrous ruthenium oxide thin films during the charging/discharging cycles. Unambiguous changes in the Raman spectrum were observed as protons were injected or extracted from the thin film. When the samples were annealed to reduce the water content, there is a consistent trend in the Raman spectrum. The origins of the Raman features and their relation to the electrochromic and/or supercapacitor characteristics is discussed.

GaAs/AlGaAs quantum-wire (QWR) gain-coupled distributed-feedback (GC-DFB) lasers are fabricated and characterized Constant metalorganic chemical vapor deposition (MOCVD) growth is used to avoid grating overgrowth during the fabrication of DFB structures. Numerical calculation shows large gain anisotropy by optical feedback along the DFB directions near Bragg wavelength. DFB lasing via QWR active gratings is also experimentally achieved.

Wurtzite GaN films are grown by low-pressure MOCVD on (0001)-plane sapphire substrates. The GaN films have a total thickness of 4 $\mu$m with a surface Mg-doped p-type layer, which has a thickness of 0.5 $\mu$m. 90k eV $Mn^{+}$ ions are implanted into the GaN films at room temperature with doses ranging from $1 \times10^{15}$ to $1 \times 10^{16}\textrm{cm}^{-2}$. After an annealing step at $770^{\circ}C$ in flowing $N_2$, the structural characteristics of the $Mn^{+}$ implanted GaN films are studied by X-ray diffraction (XRD), Rutherford backscattering spectrometry (RBS) and atomic force microscopy (AFM). The structural and morphological changes brought about by $Mn^{+}$ implantation and annealing are characterized.

In this study we report the results of ab initio first-principles calculations to investigate the possibility of metamagnetic behavior in Fe$_3$Al alloy. We used the WIEN2k package of full-potential linearized-augmented- plane-wave method within the local-spin-density approximation to the density-functional theory. The exchange-correlation functional is the generalized-gradient approximation of Perdew-Burke-Ernzerhof. The theoretical lattice constant, which is about 0.5% smaller than the experimental one, is obtained by minimizing the total energy. If the volume decreases about 9 % from the equilibrium, the total magnetic moment decreases abruptly from 4.6 $\mu_{B}$/f.u. to 4.0 $\mu_{B}$/f.u. Since this change is considerably large (∼14%), it is possible to measure by a simple high-pressure experiment at about 180 kbar.

It is experimentally shown that a $TiO_2$ film on Si(111) substrate was prepared by using the technique of D.C. reaction sputter deposition with $Ar^{+}$ ion beam bombardment, and a layer-like structure was observed from the depth profile of the interface between $TiO_2$ film and Si substrate with Scanning Electron Microscopy and Electron Probe. It was also surprisingly discovered that Ti atoms could be detected at about 9 $\mu$m depth. The $TiO_2$-Si interface bombarded by $Ar^{+}$ ion beams revealed multi-layer structures, a mechanism might be caused by defect diffusion, impurity and matrix relocation. Multi-relocations of impurity and matrix atoms were as a result of profile broadening of the $TiO_2$-Si interface, and the spread due to matrix relocation in this system is shown to exceed much more the spread due to impurity relocation.

The magnetic properties of single- and poly-crystalline $La_{0.7}Sr_{0.3}MnO_3/Pr_{0.65}Ca_{0.35}MnO_3$ multilayered (ML) films, and composite (CP) $(La_{0.7}Sr_{0.3})_{0.5}(Pr_{0.65}Ca_{0.35}_{0.5}MnO_3$ films, prepared by laser ablation, have been investigated in a wide temperature range. It was shown that the transformation from an incoherent to a coherent interface in the ML films leads to an enhancement of the ferromagnetic coupling between layers and to a single-phase magnetic transition. The amorphous CP films demonstrate a paramagnetic behavior of the magnetization with a sharp peak at $T_{G}\approx$45 K, which was interpreted as the formation of Griffiths phase. A short-term annealing at $750^{\circ}C$ induced the complete crystallization of film, and a recovery of the ferromagnetic and the metal-insulator transitions.

Sum-frequency vibrational spectroscopy has recently been used to investigate the surface of the various polymers and was able to find the chemical compositions and structures specific to the surface. Here we report our studies on two specific polymer samples to demonstrate its capability. Polyimide thin films were made by spin coating on fused quartz and $CaF_2$ substrates. The sum-frequency signal originating mainly from the air/polymer interface showed markedly different spectra, indicating the structural change of the polymer surface depending on the underlying substrate. Various polyethylene surfaces were also investigated by sum-frequency vibrational spectroscopy. The surface of polyethylene samples in the CH-region showed different sum-frequency spectra, presumably due to the trace amount of additives having much higher concentration at the air/polymer interface. These examples demonstrate the surface and interface of the polymer could have different structure and chemical composition from those of a bulk, which can be studied effectively by surface nonlinear optical spectroscopy.

In this paper, we studied, by numerical calculation, a system, which was composed of metal-film and metal-substrate irradiated by IPIB with beam ion energy 250 keV, current density 10 to 250 A/$\textrm{cm}^2$. While the IPIB irradiation was going on, an induced effect named mixing occurred. In this case, metal-film and part of metal-substrate melted and mixed. The mixing state was kept as it was in melting phase due to the fast cooling rate. Our works were simulating the heating and cooling process via our STEIPIB program and tried to find proper parameters for a specific film-substrate system, 500 nmtitanium film coated on aluminum, to get best mixing results. The parameters calculated for such Ti-Al system were compared with the experimental results and were in good accordance to the experimental results.

We present the investigation on P- and As-desorption process from the (001) InP surface in metal organic chemical vapor deposition using surface photoabsorption (SPA). The monochromatic SPA signal showed rapid initial increase to reach In-stabilized surface value after $PH_3$ was turned off, but in case of As-desorption, the signal showed clear existence of a metastable state after the $AsH_3$ was turned off. The SPA spectra at each stable surfaces were taken to confirm the interpretation. This result indicates that the As-desorption process should be understood as a two-step process, in contrast to P-desorption of one-step process.

Zirconium oxide films have been synthesized by radio-frequency magnetron sputtering deposition on n-Si(001) substrate with metal zirconium target at variant $O_2$ partial pressures. The influences of $O_2$ partial pressures of the morphology, deposition rate, microstructure, and the dielectric constant of $ZrO_2$ have been discussed. The results show that deposition rate of $ZrO_2$ films decreases, the roughness, and the thickness of the native $SiO_2$ interlayer increases with the increase of $O_2$ partial pressure. $ZrO_2$ films synthesized at low $O_2$ partial pressure are amorphous and monoclinic polycrystalline in nanometer scale at low $O_2$ partial pressure. The relative dielectrics of $ZrO_2$ films are in the range of 12 to 25.

Electromagnetic interference shielding and near-infrared cutoff filters for plasma display panel application were designed and fabricated by radio frequency magnetron sputtering. Three types of the filters were prepared: the basic structure of type A consisted of [$TiO_2$ Ti Ag $TiO_2$]; type B, of [$TiO_2$ ITO Ag $TiO_2$]; type C, of [$TiO_2$ ITO Ag ITO $TiO_2$]. Ti and ITO layers deposited on Ag layers were employed as barriers to prevent the oxidation and the diffusion of Ag film into the adjacent oxide layers. Optical, electrical, chemical, and structural properties were investigated, and the result shows that the filters with the ITO barrier layers provided an enhancement in transmittance in the visible owing to a lower absorption of ITO layers than Ti layers. Type C filter showed better optical and electrical performances and smoother surface roughness than Type B and C filters: the average sheet resistance was as low as 1.51 $\Omega\Box$ (where $\square$ stands for a square film), the peak transmittance in the visible was as high as 78.2 %, and the average surface roughness was 1.48 nm.

The sputtering yield change of an amorphous Si layer on Si(100) was measured quantitatively for 0.5 keV $O_2^{+}$ and $Ar^{+}$ ion bombardment with in suit MEIS. In the case of 0.5 keV $O_2^{+}$ ion bombardment, at the initial stage of sputtering before surface oxidation, the sputtering yield of Si was 1.4 (Si atoms/$O_2^{+}$) and then decreased down to 0.06 at the ion dose of $3\times10^{16}O_2\;^{+}\textrm{/cm}^2$. In the case of 0.5 keV $Ar^{+}$ ion bombardment, the sputtering yield of Si for the surface normal incidence was 0.56 at the ion dose of 2.5 ${\times}$ 10$^{15}$ $Ar^{+}\textrm{cm}^2$, and rapidly saturated to 1.2 at dose of $7.5\times10^{15}Ar^+\textrm{cm}^2$. For the incidence angle of 80 from surface normal, the sputtering yield of Si was saturated to about 1.4 at the initial stage of sputtering. The surface transient effects, caused by change in sputtering yield at the initial stage of sputtering can be negligible when 0.5 keV $Ar^{+}$ ion at extremely grazing angle was used for sputter depth profiling.g.

We successfully grew InN/GaN single quantum well structures by metal-organic chemical vapor deposition and confirmed their formation by optical and structural measurements. We speculate that relatively high growth temperature ($730^{\circ}C$) of InN layer enhanced the formation of 2-dimensional quantum well structures, presumably due to high adatom mobility. As the growth interruption time increased, the PL emission efficiency from InN layer improved with peak position blue-shifted and the dislocation density decreased by one order of magnitude. The high resolution cross-sectional TEM images clearly showed that the InN layer thickness reduced from 2.5 nm (without GI) to about I urn (with 10 sec GI) and the InN/GaN interface became very flat with 10 sec GI. We suggest that decomposition and mass transport processes on InN during GI is responsible for these phenomena.

The magnetoresistance (MR) of $La_{1-\chi}S_{\chi}CoO_{3-\delta}$ films prepared by pulsed-laser deposition were investigated in order to clarify the magnetotransport properties around the metal-insulator transition. For the films in the metallic state ($\chi$ > 0.25), the MR(T) manifests a small peak at the Curie temperature due to the spin-disorder scattering. The transition of the film into the insulating state ($\chi\;\leq$ 0.25) is accompanied by an essential growth of the MR and results in a significant increase in the MR(T) with decreasing temperature, due to a phase separation into the ferromagnetic-metal clusters and the insulating matrix.

In this study, the electronic structures and physical properties of Ni$_2$MnGa alloy films and their dependence on the order-disorder structural transitions were investigated. The results show that the ordered films behave nearly the same as the bulk $Ni_2$MnGa alloy, including the martensitic transformation at 200 K. Unexpectedly, the disordering in $Ni_2$MnGa alloy films does not lead to any appreciable magnetic ordering down to 4 K. An annealing of the disordered films restores the ordered structure with an almost full recovery of the magnetic and the transport properties of the ordered $Ni_2$MnGa alloy films. A possible explanation of the disappearance of magnetic moment in the disordered film is given by using the ab initio first-principles electronic-structure calculations.

The alignment effect of liquid crystals on Polyimide surfaces bombarded by a low energy argon ion beam and the effect of pretilt angle on viewing characteristics of an LCD cell are discussed. The unidirectional out-of-plane liquid crystal tilt angle is varied with various ion beam irradiation conditions, such as the energy of the incident ions, the angle of incidence and exposure time. As low pretilt angle is profitable for wider viewing property, LCD cell with ion beam modified Polyimide layer show wider viewing characteristics.

We investigate transmission of light in nanoscale structures. We present spatial and temporal domain measurements of the dephasing of surface plasmon excitations in metal films with periodic nano-hole arrays. By probing coherent spatial SP propagation lengths of a few f1. $\mu$m and an ultrafast decay of the SP polarization on a 10 fs timescale, we demonstrate that the SP transmission peaks are homogeneously broadened by the SP radiative lifetime. The pronounced wavelength and hole size dependence of the dephasing rate shows that the microscopic origin of the conversion of SP into light is a Rayleigh-like scattering by the periodic hole array. We have experimentally studied the dephasing of surface plasmon excitations in metallic nano-hole arrays. By relating nanoscopic SP propagation, ultrafast light transmission and optical spectra, we demonstrate that the transmission spectra of these plasmonic bandgap structures are homogeneously broadened. The spectral line shape and dephasing time are dominated by Rayleigh scattering of SP into light and can varied over a wide range by controlling the resonance energy and/or hole radius. This opens the way towards designing SP nano-optic devices and spatially and spectrally tailoring light -matter interactions on nanometer length scales.

$Ni_2$MnGa films, deposited on mica and glass substrates, were studied by ferromagnetic resonance (FMR) technology. The temperature-dependent resonance field was measured and a martensitic phase transformation (MT) was found between 310 and 340 K, exhibiting an abnormality on the curve. The easy axis is found to be in the film plane. The line width increases as a whole with decreasing temperature, which is discussed in terms of the motional narrowing mechanism. The resonance field was also measured as a function of orientation and the results were fitted, exhibiting a good consistence.