Effective jamming in electronic warfare depends on proper jamming technique selection and jamming parameter estimation. For this purpose, this paper proposes a new method of estimating jamming parameters using Gaussian kernel function networks. In the proposed approach, a new method of determining the optimal structure and parameters of Gaussian kernel function networks is proposed. As a result, the proposed approach estimates the jamming parameters in a reliable manner and outperforms other methods such as the DNN(Deep Neural Network) and SVM(Support Vector Machine) estimation models.

This study proposes a novel structure for the cross-eye, one of the representative jamming techniques of monopulse sensors. The proposed jammer tranceivers are composed of multi-channels with phased array antenna. We named this structure PRCJ(Phased array Retrodicetive Cross-eye Jammer). In this structure, formulas for calculating cross-eye gain and distance error are derived. We compare the properties of PRCJ with two-element retrodiredtive cross-eye jammer(TRCJ). PRCJ can achieve higher J/S because this structure can steer the spatially combined jamming signal in the direction of the incident monopulse signal. Because of the multiple channels in the phased array, it also increases the degree of freedom of channel matching. Finally, We preform a statistical analysis of the cross-eye gain according to the amplitude and phase errors. From this results, It has been found that PRCJ can get higher cross-eye gain than TRCJ.

In order to estimate the launch point of a high-speed vehicle, predicting the various characteristics of the vehicle's movement, such as drag and thrust, must be preceded by the estimation. To predict the various parameters regarding the vehicle's characteristics, we build the IMM filter specialized in predicting the parameters of the post-launch phase based on flight dynamics. Then we estimate the launch point of the high-speed vehicle using Inverse Dynamics. In addition, we assume the arbitrary error level of the radar for accuracy of the prediction. We organize multiple-dimensioned IMM structures, and figure out the optimal value of parameters by comparing the various IMM structures. After deriving the optimal value of parameters, we verify the launch point estimation error under certain error level.

Due to the continued demand for high-definition video, video compression technology is steadily developing and the High Efficiency Video Coding standard was established in 2013. However, despite the development of this compression technology, it is very difficult to smoothly transmit VGA-level videos in Ultra-narrowband environments. In this paper, the target information preprocessing algorithm is presented for smooth transmission of target images moving in forest or open-terrain in Ultra-narrowband environment. In addition, for algorithm verification, the target information preprocessing algorithm was simulated and the simulated results were compared with the video compression result without the algorithm being applied.

This study is for a bulletproof experiment through speed acceleration of steel ball(2.385 mm) at the laboratory level. The secondary propulsion method is used for speed acceleration, which uses a sabot assembly consisting of a sabot body, a plunger, water, and a sabot cap. At the core of the secondary drive, it is important that the energy in the water of the private particle is transferred well to the steel ball. The experiment was conducted by selecting a plunger that pushes water and water charged with variables. judging that the longer the contact time, the greater the energy transferred to the steel ball. As a result of experiments with each variable, the amount of water does not affect the speed acceleration efficiency of the steel ball and, when the length of the plunger is increased by 200 %, the speed of the steel ball can be accelerated up to 130 m/s.

In this study, numerical analysis was carried out on a complex pressure field of blast waves caused by the detonation of high explosives in various environments. The generated blast waves propagated in the air, upon the sudden release of high energy induced by the explosion. Reflected waves were created when the pressure waves encountered certain obstacles such as the ground or the walls of structures. The propagation of the blast waves and its interaction with the reflected waves were simulated. An adaptive mesh refinement was applied to improve the efficiency of distribution of computer resource, for the computational calculation of the blast wave propagation in a wide open space. In addition, the integration of the calculation domains for the explosive and air were considered when the maximum density of the explosive region was below critical value. The results were verified by comparison with the pressure time history from blast wave experiments performed under two topographical conditions.

In this paper, a 2-dimensional phase comparison direction finding receiver was designed and fabricated. For 2-D comparison direction finding, direction finding formulas were derived from a uniformly arranged of four antennas. Based on this, a direction finding receiver was designed using Matlab simulink, and the direction finding receiver was fabricated. To analyze the performance of the designed direction finding receiver, the injection direction finding accuracy and simulation results were compared. As a result of the test, the fabricated direction finding receiver showed a maximum of 3° RMS precision, and the result of both tests showed similar trends. Also, it was confirmed that the direction finding accuracy of elevation angle is about 2.7 times better than azimuth angle, and both models performed well within 0.7° RMS at the boresight.

Many technologies are being studied to reduce the RCS(Radar Cross Section) of stealth aircraft. Most RCS-reduction technlogies correspond to platforms. It is important to identify factors that RCS performance through simulation analysis of aircraft Mounted equipment. In particular, there are no studies of RCS performance in the radar frequency band when antenna transmit signals are applied. In this paper, the RCS performance variation on the transmit signal on/off of antennas mounted on a stealth aircraft was verified. Antennas were selected for each frequency band and simulated analysis to the RCS performance changes during antenna transmitting signal. Finally, to verify the characteristics of the change in RCS performance, RCS test measurements on the low-profile antenna transmit signal on/off were performed. In addintion, antenna RCS test measurement was performed according to the change of transmit signal power output. As a result, it was confirmed that there is no change in RCS performance when an antenna transmit signal is applied.

Enemy information has significant value when it comes to the process of military actions in battle field. Our Army now uses Battlefield Management Systems(BMSs) equipped in Ground Fighting Vehicles(GFVs) and we need to make research on what kind of role enemy information can play in such systems. Also, enemy information can be shared among GFVs and target information shall be extracted from it in view of KVMF scheme. Because KVMF becomes requisite standard in modern BMSs, we need to implement target information handling process in KVMF standard. In this article, we will focus on how target information and its sharing process can be managed efficiently without information conflicts. Also, situation map produced by it will be noted.

Technology growth curve methodology is commonly used in technology forecasting. A technology growth curve represents the paths of product performance in relation to time or investment in R&D. It is a useful tool to compare the technological performances between Korea and advanced nations and to describe the inflection points, the limit of improvement of a technology and their technology innovation strategies, etc. However, the curve fitting to a set of survey data often leads to model mis-specification, biased parameter estimation and incorrect result since data through survey with experts frequently contain outlier in process of curve fitting due to the subjective response characteristics. This paper propose a method to eliminate of outlier from a technology growth curve using M-estimator. The experimental results prove the overall improvement in technology growth curves by several pilot tests using real-data in Defense Science and Technology Survey reports.

Delivering the weapons system requirements of the military to the acquirer is an essential activity for the development of the defense industry as well as the successful acquisition of a weapons system. In order to ensure successful delivery of requirements, the creation of a weapons system Operational Requirements Document(ORD) has been mandated since 7. 2013. However, according to the results of a study which analyzes recently-created ORD, a number of problems are occurring. For one, some items in created ORDs differ from what the ORD template requires. In addition, the overall mission area of the weapons system to be acquired and the core parts(operation performance, system performance, and core performance) of ORD are being poorly recorded. In response, this study presented a framework(focused on a creating method of overall contents and core parts) for the creation of ORDs which can solve the problems that arose during ORD creation in the past.