In recent years, shipboard noise control is attracting increasing attention to human environmental conditions and crew's opportunity for rest and recreation with work on board. In order to minimize the noise levels, careful attention have to be paid by the experts from initial design stage to the delivery. This paper describes the outlines of shipboard noise control including general characteristics of shipboard noise, measurement, evaluation, prediction, and control measures considering the noise transmission mechanism from source to receiver space.

Global strength check for TLP tendon body can be estimated based on maximum tendon tensions and bending moments, which are resulted in TLP global performance analysis. Final tendon length, especially thread length on Length Adjustment Joint, is easily calculated with water depth at TLP in-place location, TLP lock-off draft and unlocking length of tendon bottom section. And LAJ thread length, which is locked with TLP top tendon connector, should be carefully determined with tendon design and installation tolerances.

Generally wave buoy and visual observation are used to measure sea waves. But the wave buoy cannot be applicable for the ship moving in deep sea. So the visual observation has been used for it. But it has several defects and limitation related to environmental condition and observer. To overcome this problem, various wave measurement systems have been suggested. Recently, the wave measurement systems using nautical X-band radar have been developed and extended its application area. In this report, we introduce the wave measurement system, WaveFinder, developed by authors. The system was calibrated and verified with the measurement results of wave buoy. The system was adopted to measure wave condition during sea trials. The system will be a device to support safe navigation in ship's voyage.

In rough seas, water breaker of the sea-going ships is subject to high impact loads due to the green water and some ships' water breaker suffers structure damage. So, a substantial research on the structural response caused by green water impact is required. In this paper, the green water flow on bow deck is simulated by FDM(finite differential method). Using the results of green water simulation, impact loads on water breaker are calculated. Calculation results of the 6200TEU container ship's structural response to this green water impact pressure are shown and discussed for two condiered calculation conditions.

For ships of ice class, finish Maritime Administration(FMA) requires brackets on intersections between longitudinal frames and the web frames within the ice-strengthened area. The main object of this paper is to verify ultimate load carrying capacity of longitudinal frame without brackets of engine room region of 74,100 DWT Product Oil Tanker. Comparative approach between proposed structures from builder (the proposed structure) and structures satisfying the Finnish-Swedish ice class rules (the rule structure) is used for the analysis.

For ships, heat resistant coating is applied on the aluminized steel pipe systems dealing with high temperature steam over $200^{\circ}C$. The coatings on these steam pipes should retain both heat resistance and anti-corrosion properties to provide long-term resistance against coating defects (rust, delamination and crack) under the harsh outdoor environment including repeated seawater wetting and condensation. Thus, it is important to improve the coating qualities and to reduce maintenance works for these steam pipe systems. In this study, five different commercial heat resistant coatings (A, B, C, D, E) were selected for evaluation. Various physical properties of these coatings were evaluated on the coatings applied on the aluminized steam pipes. FT-IR analysis was also employed to identify the factors contributing the degree of heat resistance and durability of each coating material. The results indicated that the heat resistance capacity of coatings increased with the increase of silicon content as well as the decrease of substituent content. Both products C and D showed the best coating qualifies, which can be standard coating systems for future steam pipe areas.

When the vibration troubles occur on the ship structure during the sea trial, the rectification work is very restricted because of in-situ limitation. Usually the finite element method is used to improve vibration characteristics of the structure, but it takes lots of time and effort in modeling the structure and adjusting the finite element model in order to consider appropriate boundary conditions of a complex ship structure. Therefore, experimental methods have been in general suggested to obtain proper countermeasures without time-consuming in modeling. In this paper, FRF(frequency response function) synthesis method is applied to estimate natural frequency of the modified ship structure, which is obtained from experimental and numerical methods.

Most important factor to consider funnel performance is exhaust gas temperature and exhaust gas concentration Electric equipments on the wheelhouse top affected exhaust gas temperature. So, it is important that electric equipments keep away from high temperature. Though exhaust gas concentration is not a regulation and restraint, the exhaust 9as can cause serious problems for the on-board air quality and result in irreversible damage to the ship and people. So, we pocus on the exhaust gas concentration also. When judge whether a measured concentration is acceptable or not, criteria based on the LTEL (Long Term Exposure Limit). In this paper, we carried out the smoke simulation study. For this analysis, we used FLUENT which is commercial CFD (Computational Fluid Dynamics) code.

In this paper, we introduce prediction program of HVAC system, HJNOVAC Version 2.0. The developed program adopts both the authentic empirical method suggested by NEBB and acoustic power balancing method. The program provides intuitive pre- and post- processor using modern GUI function to help efficient modeling and evaluation of cabin and HVAC component noises. To verify the accuracy and convenience of the program, we carry out noise prediction of HVAC system for 8,100 TEU Container Carrier and measure the noise levels of cabins during sea trial.

Preliminary conceptual design of hulls is developed and a theoretical evaluation study performed for the comparison of the hull concepts. Systematic variation of the side hull location is carried out to find an optimum position of side hulls for a trimaran by CFD computation. In order to compare computed results, the model test of trimaran was carried out. Shallow water effect is considered due to the route which has critical water depth of 20m for the design speed and investigated on the condition of different speeds and water depth by the numerical computations.

In recent booming up of the ship building market, the supplying of large scale casting is difficult to keep the delivery schedule for ship yard because of the restrict manufacturer in Korea. And also, it is main cause to rise-up the cost of castings. This paper describes the outline of guidance of optimizing design for Rudder Horn Casting to reduce the risk of the delivery problem to ship yard.

Recently, the Session of MSC $80^{th}$ has adopted the new harmonized requirements of damage stability for Passenger, Ro-Ro Passenger ship and Ory Cargo ship based on the probabilistic analyzing method reflecting the study of IMO for more than ten years. This paper introduces what have been changed in the SOLAS requirements about SDS (Subdivision and Damage Stability) and the results of investigation for design effects according to the new rules.

The objective of this paper is to find out a reasonable method for docking analysis of ships. The characteristics of reaction force distribution under docking condition are investigated by carrying out parametric study. To assess the allowable reaction force on keel block from structural strength point of view, two kinds of structural assessment methods are proposed in accordance with expected collapse pattern. In order to verify the proposed method, linear buckling and elasto-plastic large deflection analyses of typical double bottom structure are carried out and the results are compared.

Until now, we are designing the breakwater of container vessel as cantilever structure ypically. Recently, we have designed "side shell touch type breakwater" for the first time to 6,200TEU Class Container Carrier registered on Lloyd Classification. The Lloyd Rule does not provide requirements for breakwater scantling but only recommend breakwater wave load and Lloyd Class requests for submitting the calculation results. At early design step, we had reviewed the breakwater structure through the calculation of simple beam theory with wave load recommended by Lloyd and referring to already built same size of container vessel. At the same time we had carried out F.E.M analysis of breakwater structure and had updated design, so we could verify the strength of side shell touch type breakwater at final step.

The steel outfitting structures installed in engine room are vibrated by an excitation of the engine and the propeller. Vibration problems such as cracks and fitting breakages are mainly induced at the near range of the resonance. The excitation frequency estimation is possible by engines and propeller specifications, but the natural frequency of a steel outfitting structure is not easily estimated due to the complication and variety of the designed shape. This paper represents natural frequency data of simple steel outfitting structures. As a vibration analysis tool, MSC/NASTRAN was used to calculate natural frequencies. Natural frequencies were compared in case of the shape and boundary condition changes of simple models, and anti-vibration models of the steel outfitting structures were presented on the basis of results.

The vertical displacement of a ship on the basis of the sea level is an important parameter for its stability and control. To indicate the displacement on operating conditions, "draft marks" are carved on the hull of the ship in various ways. One of the methods is welding. The position, shape and size of the marks are specified on the shipbuilding rules by classification societies to be checked by shipbuilders. In most cases, high-skilled workers do the welding along the drawing for the marks and welding bead becomes the marks. But the inaccuracies due to human errors and high labor cost increase the needs for automating the work process of the draft marks. In the preceding work, an indoor robot was developed for automatic marking system on flat surfaces and the work proved that the robot welding was more effective and accurate than manual welding. However, many parts of the hull structure constructed at the outdoor are cowed shapes, which is beyond the capability of the robot developed for the indoor works on the flat surface. The marking on the curved steel surface requiring the 25m elevations is one of the main challenges to the conventional robots. In the present paper, the robot capable of climbing vertical curved steel surfaces and performing the welding at the marked position by effectively solving the problems mentioned earlier is presented.

In case of lap joint fillet welds of thin plate, the example which is applicable to Plasma Welding increases substituting for the exiting TIG Welding but the quality of Plasma arc welding has a special feature influenced sensitively by the condition of welding caused by controlling the various parts of welding torch. This research is purposed to improve lap joint fillet welds of thin plate in high quality and attain the high productivity and it is examined that how the change of electrode tip angle and Setback has an effect on the quality of welding and it is investigated how the change of Setback and Standoff has an effect on Melting efficiency using Response Surface Analysis.

Generally, porosity which was formed by pyrolysis of the primer is usually generated in the weld metal in respect of increase of the welding speed. in order to analyze the cause of porosity generation, this study was performed using FCAW(flux cored arc welding) process for three kinds of inorganic.zinc primer. in addition the evaluation by influence of welding method on porosity generation is conducted to compare between FCAW and MAG(metal active gas) welding with the same inorganic zinc primer. As the result of this investigation, not only primer of lower organic binder and zinc but also FCAW process than MAG in fillet welding have been verified the excellent resistance to the porosity generation for horizontal fillet welding.