• 한국분말재료학회지
• /
• 제25권4호
• /
• pp.331-335
• /
• 2018

This study investigates the directional recrystallization behavior of Ni based oxide dispersion strengthened (ODS) alloy according to the zone annealing velocity. The zone annealing temperature is set as $1390^{\circ}C$, while the zone velocities are set as 2.5, 4, 6, and 10 cm/h, respectively. The initial microstructure observation of the as-extruded sample shows equiaxed grains of random orientation, with an average grain size of 530 nm. On the other hand, the zone annealed samples show a large deviation in grain size depending on the zone velocities. In particular, grains with a size of several millimeters are observed at 2.5-cm/h zone velocity. It is also found that the preferred orientation varies with the zone annealing velocity. On the basis of these results, this study discusses the role of zone velocities in the directional recrystallization of Ni base ODS alloy.

• Journal of Biosystems Engineering
• /
• 제10권1호
• /
• pp.76-82
• /
• 1985

To investigate the influence of annealing heat treatment on the mechanical properties at the various weld zone, an experimental study was performed for the structural alloy steel. The results obtained from the experimental works are as follows: 1. Hardness and tensile strength showed the highest value at the heat affected zone, which was 5mm apart from bond zone. With increasing of annealing temperature, hardness and tensile strength were decreased at every weld zone, and bound in heat affected zone was increased. 2. Impact strength was the highest at the filler metal, and increased with increment of annealing temperature at filler metal and base metal. However, both at bond and heat affected zones, impact strength was increased from $700^{\circ}C$ of annealing temperature, and was decreased again over $900^{\circ}C$. 3. Mutual relationship between the mechanical properties at filler and base metals showed a similar linearty to that the common structural steel did. However, it varied unsteadly both at bond and heat affected zones. 4. It may be concluded that proper annealing temperature is $700^{\circ}C$ from the viewpoint of hardness, tensile and impact strength.

• 한국세라믹학회지
• /
• 제53권4호
• /
• pp.411-416
• /
• 2016

Benzothienobenzothiophene ($C_8-BTBT$) is a soluble organic small molecule material with high crystallinity resulting from its strong self-organizing properties. In addition, the high mobility and easy fabrication of $C_8-BTBT$ make it very attractive in terms of organic thin-film transistors. In this work, we made $C_8-BTBT$ thin films by using the zone-casting method; we also used an organic solvent to treat the devices with solvent vapor annealing to improve the electrical properties. As a result, we confirmed improved mobility, threshold voltage, and subthreshold swing after solvent vapor annealing. To prove the effect of solvent vapor annealing, we used the simultaneous extraction model to extract the contact resistance from the current-voltage curve. We confirmed that the electrical properties improved with decreasing contact resistance.

• 한국안전학회지
• /
• 제2권3호
• /
• pp.5-11
• /
• 1987

In this study, a mild steel (SS41) of the carbon steel, a spring steel (SUP-9), and stainless steel (SUS 304) of the special gceel, etc, are adopted as the experimental materrials and are weded by $CO_2$(SS41, SUP-9), TIG (SUS304), respectively. And the residual stress distribution and fracture behavior at the welded zone are examined according to annealing temperatures of four section involving as welded. As a consequence, the best annealing temperatures that the residual stress is removed enough and mechanical properties are very suitable are at 90$0^{\circ}C$ (SS41), 75$0^{\circ}C$ (SUP-9), 110$0^{\circ}C$ (SUS 304), respectively.

• 한국정밀공학회지
• /
• 제11권2호
• /
• pp.173-181
• /
• 1994

A Cold spot temperature control system for the batch annealing furnace has been estabilished in order to reduce energy consumption to improve productivity and stabilize the propertics of products. Therefore we confirmed a relation between annealing cycle time and atmospheric gas, variation of coil cold spot temperature with time during heating and actual temperature measurements at mid-width of each coil during heating and actual temperature measurements at mid-width of each coil during soaking. The results of the tempaeature variation effect on the batch annealing are as follows. 1) Heating time is reduced to one half with increasing atmospheric gas flow rate and changing of atmospheric gas component from HNx to Ax gas, and annealing cycle time is reduced to 2.7 times. 2) In case of short time healing, the slowest heating part is the center of B coil, in case of long time heating, the low temperature point moves from the center of coil to inside coil. And the temperature in this part is higher than other parts when cooling. When finished heating, the cold spot is located 1/3 of coil inside in case of HNx atmospheric gas. But center of coil in case of Ax atmospheric gas. 3) The outside of top coil is the highest temperature point when heating, which becomes the lowest temperature point when cooling. So, this point becomes high temperature zone at heating and low temperature zone at cooling, It has relation according to atmospheric gas component and flow rate. 4) Soaking time at batch annealing cycle determination is made a decision by the input coil width, and soaking time for quality homogenization of 1214mm width coil must be 2.5 hours longer than that of 914mm width coil for the same ciol weight. 5) Annealing cycle time with Ax atmospheric gas is extended 1 hour in of slow cooling during 5 hours in order to avoid rapid cooling.

• 한국결정성장학회지
• /
• 제5권2호
• /
• pp.87-93
• /
• 1995

Floating zone법으로 strontium titanate 단결정을 육성하였다. 성장조건은 공기 분위기하에서 성장속도 3mm/hr, 상부축 회전속도 20~25rpm, 하부축 회전속도 15~20rpm이었으며 육성한 단결정은 옅은 갈색을 띄고 있었으며 투명하였고 annealing 후 색깔이 옅어짐을 확인할 수 있었다. 성장방위는 [112] 방향이었으며 XRD, EDS로 화학양론적인 조성은 $SrTiO_3$단일 결정상임을 알 수 있었다. $350^{\circ}C$, KOH용액에서 5분동안 chemical etching하여 etch pit pattern을 조사하였으며 상온하에서$350^{\circ}C$의 온도 범위에서 유전상수 값을 조사하였다.

• 한국전기전자재료학회논문지
• /
• 제17권11호
• /
• pp.1178-1185
• /
• 2004

In the atmosphere of $N_2$ gas, BaZ $r_{0.08}$ $Ti_{0.92}$ $O_3$ polycrystal was grown by floating zone technique using BaZ $r_{0.08}$ $Ti_{0.92}$ $O_3$ ceramics as a feed and SrTi $O_3$(1l0) single cystal as a seed. The dielectric constant and loss at 10 kHz, 100 kHz, and 1 MHz for the as-grown sample were measured as a function of temperature in the temperature range between -10$0^{\circ}C$ and 150 $^{\circ}C$ to find a dielectric peak with frequency dispersion at Curie point. The hysteresis loop showed that the grown sample had very small polarization which was 0-0.01 $\mu$C/$\textrm{cm}^2$ for the applied dc-electric fields from -7 kV/cm to +7 kV/cm. However, the normal hysteresis loop was appeared after oxygen annealing. The electric-field dependence of the dielectric constant for both the as-grown and the post-annealed samples was studied by measuring the dielectric constants as a function of the biased-electric fields and their tunability was figured out from it at room temperature(27 $^{\circ}C$) and cryotemperature( -73$^{\circ}C$). Tunability for the as-grown sample was 51 % and the figure of merit 20.4 at 10kHz with the biased electric-field of 12 kV/cm. The tunability for the grown sample may be increased up to 80 % if the electric field of 25 kV/cm is applied. Tunability for the post-annealed sample was 41 % and the figure of merit 10.3 at 10 kHz with the biased electric-field of 12 kV /cm. Post-annealing improved the crystallinity of the as-grown sample but decreased its tunability.ability.

• 한국결정성장학회지
• /
• 제28권4호
• /
• pp.152-158
• /
• 2018

PVT(Physical vapor transport)법은 고품질의 대면적 웨이퍼를 생산하기에 이점을 가져 질화물계 반도체의 상용화를 위해 많은 연구가 진행되고 있는 단결정 성장 방법이다. 하지만 복잡한 공정 변수들로 인하여 비평형적인 성장 조건을 갖게 될 경우 수많은 결함들이 발생하게 된다. 결정성장 후 어닐링 공정은 결정성 개선을 위해 널리 사용된다. 효과적인 결정성 개선을 위해서는 적절한 온도, 압력과 시간을 설정하는 게 중요하다. 본 연구에서는 PVT법으로 성장된 AlN 단결정 및 어닐링 조건에 따른 단결정의 결정 미세구조 변화를 X-ray topography, Electron Backscattered Diffraction(EBSD), Rietveld refinement를 통해 분석하였다. Synchrotron Whitebeam X-ray topography 분석 결과 어닐링을 진행하지 않은 단결정에 2차상 및 sub grain, impurity가 존재하였으며 이로 인해 결정성이 저하되는 것을 확인 할 수 있었다. EBSD 결과 어닐링을 진행한 시편의 경우 결정립수가 증가함과 동시에 basal plane의 뒤틀림이 일어나는 것을 관찰할 수 있었다. Rietveld refinement 결과 일부 격자들이 a, b, c축 방향으로 응력을 받아 변형된 것으로 분석되었다. 이는 어닐링 과정 중 hot zone 내의 상하 온도구배에 의해 발생한 응력으로 결정립 방향의 뒤틀림이 일어날 뿐만 아니라 격자 상수가 달라진 것으로 분석된다.

• 전자공학회논문지A
• /
• 제32A권1호
• /
• pp.179-184
• /
• 1995

Phosphorous was deped in silicon thin films by Ion Mass Doping and Changes in the electrical resistance with respect tko heat treatments were investigated. SOI(Silicon On Insulator) thin films which contain few grain boundaries prepared by ZMR(Zone Melting Recrystallization) of polysilicon films, polysilicon films which have about 1500 $A^{\rarw}$ of grain size prepared by LPCVD at 625.deg. C, and amorphous silicon thin films prepared by LPCVD at low temperature were used as substrates and thermal behavior of phosphorous after RTA(Rapid Thermal Annealing) and furnace annealing was carefully studied. Amorphous thin films showed about 10$^{6}$ .OMEGA./ㅁbefore any heat treatment, while polycrystalline and SOI films about 10$^{3}$.OMEGA./¤. All these films, however, showed about 10.OMEGA./ㅁafter furnace annealing at 700.deg. C for 3hrs and RTA showed about the same trend. Films with grain boundaries showed a certain range of heat treatment which rendered increase of the electrical resistance upon annealing, which could not be observed in amorphous films and segregation of doped phosphorous by diffusion with annealing was thought to be responsible for this abnormal behavior.

• Corrosion Science and Technology
• /
• 제13권2호
• /
• pp.48-55
• /
• 2014

Influence of annealing temperature on the microstructure and resistance to pitting corrosion of the hyper duplex stainless steel was investigated in acid and neutral chloride environments. The pitting corrosion resistance is strongly dependent on the microstructure, especially the presence of chromium nitrides ($Cr_2N$), elemental partitioning behavior and volume fraction of ferrite phase and austenite phase. Precipitation of deleterious chromium nitrides reduces the resistance to pitting corrosion due to the formation of Cr-depleted zone. The difference of PREN (Pitting Resistance Equivalent Number) values between the ferrite and austenite phases was the smallest when solution heat-treated at $1060^{\circ}C$. Based on the results of electrochemical tests and critical crevice temperature tests, the optimal annealing temperature is determined as $1060^{\circ}C$.