• 한국세라믹학회지
• /
• 제32권1호
• /
• pp.95-105
• /
• 1995

Ceria(CeO2) stabilized zirconia(CeSZ) sol was synthesized with zirconium n-butoxide Zr(OC4H9)4 and cerium nitrate hexahydrate Ce(NO3)3.6H2O as precursors and ethylacetoacetate(EAcAc) as a chelating agent under atmosphere. CeSZ films were deposited on AISI 304 stainless steel using the prepared polymeric sol by dipcoating and the coating characteristics were investigated by XRD, ellipsometry, scratch test and SEM. The CeSZ film began to crystallize from amorphous to tetragonal phase at 40$0^{\circ}C$ and it was not converted into monoclinic phase up to 100$0^{\circ}C$ by the addition of 16mol% CeO2 as a stabilizer which could suppress phase transformation of zirconia. The CeSZ films were prepared by varying the EAcAc contents and the cncentration of CeSZ sol and measured the thickness and refractive index. From these results, it was found that the EAcAc contents and concentration of CeSZ coating sol evidently affect the densification of CeSZ film. The CeSZ film coated with 0.4M CeSZ sol and heat-treated at $600^{\circ}C$ for 10min had thickness of 50nm and 17% porosity. The CeSZ film on 304 stainless steel effectively acted as a protective layer against oxidation up to 80$0^{\circ}C$ and had superior corrosion resistance in 25% H2SO4 solution for 4.5 hrs.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 디스플레이 광소자분야
• /
• pp.86-89
• /
• 2004

Organic thin film transistors (OTFTs) are fabricated on the plastic substrate through 4-level mask process without photolithographic patterning to yield the simple fabrication process. And we herewith report for the effect of dielectric surface modification on the electrical characteristics of OTFTs. The KIST-JM-1 as an organic molecule for the surface modification is deposited onto the surface of zirconium oxide $(ZrO_2)$ gate dielectric layer. In this work, we have examined the dependence of electrical performance on the interface surface state of gate dielectric/pentacene, which may be modified by chemical properties in the gate dielectric surface.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.193-193
• /
• 2011

To obtain ceramic films, the sol-gel coating technique has been broadly used with heat treatment, but crack formation tend to occur during heat treatment in thick sol-gel films. We prepared PZT thin films by sol-gel method with single-step spin coating process. The PZT solution have been synthesized using lead acetate ($Pb(CH_3COO)_2$), zirconium acetylacetonate ($Zr(OC_3H_7^n)_4$), and titanium diisopropoxide bis(acetylacetonate) 75wt% in isopropanol ($Ti(OC_3H_7^i)_2(OC_3H_7^n)_2$) as starting materials and n-propanol was selected as a solvent. The poly(vynilpyrrolidone) (PVP) was added with 0, 0.25, 0.5, 0.75, and 1 molar ratios to control viscosity of solution. We investigated influence of the viscosity on thickness, microstructure, and electrical properties of final PZT films. Thermo-gravimetric analysis and differential scanning calorimeter (TGA/DSC) was carried out from room temperature to $800^{\circ}C$ in order to measure pyrolysis temperature. Structural characteristics were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Ferroelectric and dielectric properties were measured by RT66A (Radiant) and impedance analyzer (Agilent), respectively. The thicknesses of PZT films depended on incorporation of an excess amount of PVP. Finally, we obtained PZT films of good quality without crack formation via single-step spin coating.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.115-119
• /
• 2003

The thick film type sensor having Pt/Na Super Ionic Conductor(NASICON) solid electrolyte/Pt/$Na_2$$SO_4$/Pt catalyst system for $SO_2$gas was fabricated by screen-print method. The phase of Na Super Ionic Conductor solid electrolyte sintered at different temperature of 1050, 1150,$ 1250^{\circ}C$ and for different time of 1.5, 2.5, 3.5 hr were investigated by XRD. The Electromotive Force variation of the sensor with $SO_2$concentrations and operating temperatures were investigated. The major phase of Na Super Ionic Conductor film sintered at 115$0^{\circ}C$ for 3.5 hr was sodium zirconium silicon phosphate($Na_3$Zr$_2$$Si_2$PO$_{12}$). The Nernst's slope of Na Super Ionic Conductor sensor for $SO_2$gas with the variation of concentration from 10 to 100 ppm was 167.14 ㎷/decade at the operating temperature of $500 ^{\circ}C$. The increase of oxygen partial pressure was not affected to the variation of Nernst's slope.e.

• Bulletin of the Korean Chemical Society
• /
• 제27권1호
• /
• pp.65-70
• /
• 2006

An amperometric glucose biosensor has been developed based on the use of the nanoporous composite film of sol-gel-derived zirconia and perfluorosulfonated ionomer, Nafion, for the encapsulation of glucose oxidase (GOx) on a platinized glassy carbon electrode. Zirconium isopropoxide (ZrOPr) was used as a sol-gel precursor for the preparation of zirconia/Nafion composite film and the performance of the resulting glucose biosensor was tuned by controlling the water content in the acid-catalyzed hydrolysis of sol-gel stock solution. The presence of Nafion polymer in the sol-gel-derived zirconia in the biosensor resulted in faster response time and higher sensitivity compared to those obtained at the pure zirconia- and pure Nafion-based biosensors. Because of the nanoporous nature of the composite film, the glucose biosensor based on the zirconia/Nafion composite film can reach 95% of steady-state current less than 5 s. In addition, the biosensor responds to glucose linearly in the range of 0.03-15.08 mM with a sensitivity of 3.40 $\mu$A/mM and the detection limit of 0.037 mM (S/N = 3). Moreover, the biosensor exhibited good sensor-to-sensor reproducibility (~5%) and long-term stability (90% of its original activity retained after 4 weeks) when stored in 50 mM phosphate buffer at pH 7 at 4 ${^{\circ}C}$.

• Nuclear Engineering and Technology
• /
• 제50권2호
• /
• pp.218-222
• /
• 2018

An oxide-dispersion-strengthened (ODS) layer was formed on Zircaloy-4 tubes by a laser beam scanning process to increase mechanical strength. Laser beam was used to scan the yttrium oxide ($Y_2O_3$)-coated Zircaloy-4 tube to induce the penetration of $Y_2O_3$ particles into Zircaloy-4. Laser surface treatment resulted in the formation of an ODS layer as well as microstructural phase transformation at the surface of the tube. The mechanical strength of Zircaloy-4 increased with the formation of the ODS layer. The ring-tensile strength of Zircaloy-4 increased from 790 to 870 MPa at room temperature, from 500 to 575 MPa at $380^{\circ}C$, and from 385 to 470 MPa at $500^{\circ}C$. Strengthening became more effective as the test temperature increased. It was noted that brittle fracture occurred at room temperature, which was not observed at elevated temperatures. Resistance to dynamic high-temperature bursting improved. The burst temperature increased from 760 to $830^{\circ}C$ at a heating rate of $5^{\circ}C/s$ and internal pressure of 8.3 MPa. The burst opening was also smaller than those in fresh Zircaloy-4 tubes. This method is expected to enhance the safety of Zr fuel cladding tubes owing to the improvement of their mechanical properties.

• 치위생과학회지
• /
• 제22권3호
• /
• pp.191-198
• /
• 2022

Background: The purpose of this study was to evaluate the composition of the crystal phases of various calcium silicate-based materials (CSMs): ProRoot white MTA^Ⓡ (mineral trioxide aggregate) (WMTA), Ortho MTA^Ⓡ (OM), Endocem MTA^Ⓡ (EM), Retro MTA^Ⓡ (RM), Endocem Zr^Ⓡ (EN-Z), Biodentine^TM (BD), EZ-seal^TM (EZ), and OrthoMTA III (OM3). Methods: In a sample holder, 5 g of the powder sample was placed and the top surface of the material was packed flat using a sterilized glass slide. The prepared slides were mounted on an X-ray diffraction (XRD) instrument (D8 Advance; Bruker AXS GmbH, Germany). The X-ray beam 2θ angle range was set at 10~90° and scanned at 1.2° per minute. The Cu X-ray source set to operate at 40 kV and 40 mA in the continuous mode. The peaks in the diffraction pattern of each sample were analyzed using the software Diffrac (version 2.1). Then, the peaks were compared and matched with those of standard materials in the corresponding Powder Diffraction File (PDF-2, JCPDS International Center for Diffraction Data). A powder samples of the materials were analyzed using XRD and the peaks in diffraction pattern were compared to the Powder Diffraction File data. Results: Eight CSMs showed a similar diffraction pattern because their main component was calcium silicate. Eight CSMs showed similar diffraction peaks because calcium silicate was their main component. Two components were observed to have been added as radiopacifiers: bismuth oxide was detected in WMTA, OM, and EM while zirconium oxide was detected in RM, EN-Z, BD, EZ, and OM3. Unusual patterns were detected for the new material, OM3, which had strong peaks at low angles. Conclusion: It was caused by the presence of Brushite, which is believed to have resulted in crystal growth in a particular direction for a specific purpose.

• 청정기술
• /
• 제19권3호
• /
• pp.264-271
• /
• 2013

본 연구에서는 지르코늄 피복관 제조공정에서 발생되는 스크랩을 원전급(nuclear grade)으로 재활용하기 위해 스크랩 표면에 부착되어 있는 오염물 제거조건을 최적화하였다. 주 오염물은 피복관 제조시 필거링 공정에서 사용하고 있는 수용성 냉각윤활제 잔류물로서 튜브 표면에 압착 및 탄화된 것으로 가정된다. 스크랩 발생 빈도가 높은 ${\phi}9.50mm$, zirlo 합금 튜브를 피 세정 대상물로 선정하여 세정 후 피 세정물 표면에 잔존하고 있는 오염물의 특성분석과 피 세정물의 표면 성분분석으로 세정성을 평가하였다. 세정제별 세정능력을 평가하기 위하여 수산화나트륨(sodium hydroxide) 계열 2종과 수산화칼륨(potassium hydroxide) 계열 3종을 선정하여 비교하였다. 또한 온도 및 초음파 강도에 따른 세정 효과 분석을 위해 상온, $40^{\circ}C$, $60^{\circ}C$에서 각각 세정한 결과, 세정온도 및 초음파 강도가 높을수록 세정효과도 높은 것으로 나타났다. 육안검사 결과 수산화나트륨 계열은 초음파 강도와 무관하게 모두 양호한 것으로 나타났으나 수산화칼륨 계열은 초음파 강도 120 W 이상에서 피 세정물의 표면상태가 양호한 것으로 나타났다. 중량측정법에 의한 세정효과 분석결과 수산화나트륨 계열은 세정효율이 97.6% ($60^{\circ}C$, 120 W)까지 나타났으나 수산화칼륨 계열은 피 세정물의 표면상태 불량으로 중량측정 방법을 적용하는 것이 부적합한 것으로 나타났다. 피 세정물의 표면 오염물 분석 결과 C, O, Ca, Zr 성분이 검출되었으며 그 중 C, O의 성분이 대부분을 차지하였음을 알 수 있었다. 피 세정물의 세정 정도에 따라 C, O 구성 비율의 변화가 큰 것으로 나타났으며 세정이 잘될수록 C의 구성비율이 감소되며 상대적으로 O의 구성 비율이 증가되었다. 본 연구 결과를 바탕으로 산업현장에 적용하기 위하여 세정공정을 알카리세정, 수세, 건조의 3단계로 구분하고 각 단계별로 세정변수를 조정함으로써 세정효과의 극대화를 기대할 수 있다.

• 공업화학
• /
• 제32권5호
• /
• pp.524-531
• /
• 2021

UiO-66은 높은 흡착능력과 구조적 및 열적 안정성 등으로 여러 현장에 적용 가능한 금속유기골격체(MOF)이다. UiO-66은 제조과정에서 조절인자로 사용되는 산의 종류와 양에 따라 구조적 특성이 변형되고, 화학작용제 흡착 능력을 높일 수 있다고 알려져 있다. 이에 본 연구에서는 다양한 산을 조절인자로 첨가하여 UiO-66을 합성하고, 그 특성을 FT-IR, XRD, 적정장치, 그리고 유사화학작용제 diisopropyl methylphosphonate (DIMP)를 활용한 흡착실험을 통해 분석하였다. 연구 결과 UiO-66의 제조과정에서 염산을 첨가할 시 UiO-66의 Zr-OH 결합과 UiO-66의 유기연결체인 테레프 탈산 구조에 일부 손상이 있었다. 특히 이러한 구조 손상은 염산의 농도가 일정 수준 이상으로 높을 때, 그리고 합성 시간이 일정 시간 이상으로 길어질 때 발생하였다. 하지만 아세트산과 포름산을 조절인자로 활용하여 제조한 UiO-66은 구조적 손상이 발견되지 않았으며, 염산을 활용하여 제조한 UiO-66에 비하여 결정도, 비표면적, 공극의 부피, 그리고 DIMP 흡착 능력이 모두 높게 나타나 향후 화학작용제 흡착제로서 활용 가능성이 높을 것으로 판단되었다.

• 비파괴검사학회지
• /
• 제34권3호
• /
• pp.254-259
• /
• 2014

중수로 원자로는 한 개의 원자로용기로 구성된 경수로와는 달리 약 380여개의 연료채널(fuel channel)로 구성되어 있다. 연료채널을 구성하는 압력유지 기기인 압력관(pressure tube)은 지르코니움 합금(Zr-2.5wt% Nb) 재질로서 치수는 내경이 103.4 mm, 두께가 약 4.19 mm, 길이가 6.36 m인 튜브 형태의 관이다. 압력관은 내부에 핵연료 다발과 냉각재가 내장되며 압력관의 기능은 연료를 지지하고 열수송 유체인 중수($D_2O$)를 이송한다. 압력관의 단순한 기하학적인 형상으로 인하여 자동화 비파괴검사가 가능하고 접근성이 우수하다. 연료채널은 경수로형 원전과 동일하게 설치전과 운전중에 원자력안전위원회 법령 요건에 따라 주기적으로 엄격한 비파괴검사를 수행하여 건전성을 확인한다. 연료채널의 주기적 비파괴검사에는 초음파탐상 및 와전류탐상검사 기법을 적용한 체적 비파괴검사 기술이 적용된다. 이중에서 와전류탐상검사 기법은 초음파탐상검사에서 검출된 결함의 확인을 위한 보충검사기술로 적용되고 있지만 표면결함에 대한 검출능이 초음파탐상검사 기법보다 우수한 장점을 가지고 있다. 본 논문에서는 압력관 내부 표면 비파괴검사에 적용되고 있는 와전류탐상검사 기술의 압력관 내면에 발생할 수 있는 결함의 검출 및 깊이 측정 특성에 대한 연구결과를 기술하였다. 즉, 와전류검사 기술은 압력관 내면에 발생할 수 있는 아주 미세한 결함을 매우 우수한 분해능으로 검출할 수 있으므로 초음파탐상검사 결과 확인을 위한 보충기술로서 매우 유용하지만, 결함의 깊이 측정은 오차가 매우 크게 발생하므로 결함 깊이 측정에는 적합하지 않고 오직 표면결함 검출에만 적용하는 것이 바람직하다.