• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.373-379
• /
• 2001

When a train runs into a tunnel at high-speed, aerodynamic drag suddenly increases and the booming noise is generated at the exit of tunnel. The noise shape is very important to reduce the aerodynamic drag in tunnel as well as on open ground, and the micro-pressure wave that is a source of booming noise is dependent on nose shape, especially on area distribution. In this study, the nose shape has been optimized employing the response surface methodology and the axi-symmetric compressible Navier-Stokes equations. The optimal designs have been executed imposing various conditions of the aerodynamic drag and the micro-pressure wave on object functions. The results show that the multi-objective design was successful to decrease micro-pressure wave and aerodynamic drag of trains.

• Journal of the Korean Institute of Navigation
• /
• v.19 no.3
• /
• pp.1-10
• /
• 1995

The effect of the submerged high speed vessel on the ocean wave is made clear in the point of hydrodynamics view. In connection to the design of high speed ship, the flow analysis is carried out to predict the pressure distribution for drag and lift. The purpose of the research is to help the preliminary design of the economic hull form advancing under the ocean wave by estimating the resistance performance and the wave behaviour. In the present study, more efficient numerical approaches are investigated for the viscous flow analysis around a submerged NACA0012 hydrofoil with the laminar and incompressible fluid. Through the numerical simulation, it is found that the new numerical method becomes more efficient primarily due to the fact that the wave elevation is reasonably developed.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1023-1028
• /
• 2004

A micro-pressure wave is generated by the high-speed train which enters a tunnel, and it causes explosive noise and vibration at the exit. It is known that train speed, train-tunnel area ratio, nose slenderness and nose shape mainly influence on generating micro-pressure wave. So it is required to minimize it by searching optimal values of such train shape factors and tunnel condition. In this study, response surface model, one of approximation models, is used to perform optimization effectively and analyze sensitivity of design variables. Owen's randomized orthogonal array and D-optimal Design are used to construct response surface model. In order to increase accuracy of model, stepwise regression is selected. Finally SQP(Sequential Quadratic Programming) optimization algorithm is used to minimize the maximum micro-pressure wave by using built approximation model.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.2 no.2
• /
• pp.3-10
• /
• 2000

The compression wave produced when a high-speed train enters a tunnel propagates along the tunnel ahead of the train. The micro pressure wave related to the compression wave is a special physics phenomena created by high-speed train-tunnel interfaces. A among methods for the purpose of reducing the micro pressure wave is to delay the gradient of the compression wave by using aerodynamic structures. The objective of this paper is to determine the optimum slanted portal using the moving model rig. According to the results, the maximum value of micro pressure wave is reduced by 19.2% for the $45^{\circ}$ slanted portal installed at the entrance of the tunnel and reduced by 41.9% for the $45^{\circ}$ slanted portals at the entrance and exit of the tunnel. Also it is reduced by 34.6% for the $30^{\circ}$ slanted portals installed at the entrance and exit of the tunnel.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1819-1828
• /
• 1989

In this paper, we determined the modulation index for minimization of speed ripple and position error using maximum speed ripple (SRF) and maximum position error(PEF) in current source TPWM inverter. Through computer simulation, we compared with total current harmonic distortion, SRF and PEF for square wave modulation method and TPWM method. As a result, it turns out that square wave modulation method is superior to TPWM method of 3 pulses per half cycle in speed ripple and position error contents. And TPWM is better than square wave method when pulse number is more than 5. Also, in these pulse numbers, moduladtion index of minimum speed ripple and munimum position error is 0.91.

• ETRI Journal
• /
• v.35 no.4
• /
• pp.578-586
• /
• 2013

Using a sub-terahertz (sub-THz) wave generated using a photonics-based technology, a high-speed wireless link operating at up to 10 Gbps is designed and demonstrated for realization of seamless connectivity between wireless and wired networks. The sub-THz region is focused upon because of the possibility to obtain sufficient bandwidth without interference with the allocated RF bands. To verify the high-speed wireless link, such dynamic characteristics as the eye diagrams and bit error rate (BER) are measured at up to 10 Gbps for non-return-to-zero pseudorandom binary sequence $2^{31}-1$ data. From the measurement results, a receiver sensitivity of -23.5 dBm at $BER=10^{-12}$ is observed without any error corrections when the link distance between the transmitter and receiver is 3 m. Consequently, we hope that our design and experiment results will be helpful in implementing a high-speed wireless link using a sub-THz wave.

• Journal of KSNVE
• /
• v.7 no.6
• /
• pp.959-966
• /
• 1997

In general, the booming noise intensity at tunnel exit is strongly related to the gradient of the compression wave front created by high speed train entering the tunnel. This paper presents some results in relation with the compression wave front produced when the high speed train enters a tunnel. Four kinds of tunnel entrance shape with real dimensions were studied to investigate the formation of compression wave front inside tunnel by train entering tunnel. Computations were carried out using three-dimensional compressible Euler equation with vanishing viscosity and conductivity of fluid. According to the results, the flow disturbances occured at tunnel entrance were eliminated by tunnel hood with same cross sectional area. The compression wave front is formed completely at 30-40m from tunnel entrance. The maximum pressure gradient of compression wave front is reduced by 29.8% for the inclined tunnel hood and reduced by 21.5% for the tunnel hood with holes at the top face with tunnel without hood. The length of the inclined hood is 15m and the length of the hood with holes is 20m.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.627-635
• /
• 1997

In general, the booming noise intensity at tunnel exit is strongly related to the gradient of the compression wave front created by high speed train entering the tunnel. This paper presents some results in relation with the compression wave front produced when the high speed train enters a tunnel. Four kinds of tunnel entrance shape with real dimensions were studied to investigate the formation of compression wave front inside tunnel by train entering tunnel. Computations were carried out using three-dimensional compressible Euler equation with vanishing viscosity and conductivity of fluid. According to the reslts, the flow disturbance occured at tunnel entrance were eliminated by tunnel hood with same cross sectional area. The compression wave front is formed completely at 30-40m from tunnel entrance. The maximum pressure gradient of compression wave front is reduced by 29.8% for the inclined tunnel hood and reduced by 21.5% for the tunnel hood with holes at the top face with tunnel without hood. The length of the inclined hood is 15m and the length of the hood with holes is 20m.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.9 no.1
• /
• pp.103-110
• /
• 2013

WAVE system is a vehicle communication technology. The system provides the services to prevent vehicle accidents that might occur during driving. Also, it is used to provide various services such as monitoring vehicle management and system failure. In this paper, we divide module that manages WAVE MAC state into a WSMP base MLME module and IP base module and we design and implement a parameter environment between WME module to manage the state of the WAVE system and MLMEX module to mange IP base of WAVE MAC therefore the date to be processed.Also, in order to verify the validity, we have carried out experiments to compare the speed of data processing by dividing data of 5Mbyte, 10Mbyte, 20Mbyte into the packets of 2KByte and 4KByte. Therefore, in WAVE system, the Parameter environments and data processing speed between WME and MLMEX module can be utilized in the various service of vehicle communication technology depending on the speed of data processing.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.3
• /
• pp.293-300
• /
• 2013

This study used a water tank and wave maker to generate conditions similar to the real ocean environment. Given that the waves were properly generated in the water tank, a precise analysis indicated the quantitative value of the wave force acting on a body. A high-speed camera and wave-level gauge were used to measure the temporal wave motion and period. A series of artificial water waves were successfully generated using three different wave periods and amplitudes. Each of the waves captured by a high-speed camera was sinusoidal and did not maintain its shape properly without a wave absorber, but it was substantially improved and well shaped when the wave absorber was installed.