• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1400-1405
• /
• 2008

Execute surface of the earth geological survey for stability analysis of stealing cutting sides and investigated wide area nature of soil structure. Inflected DIPS that measure discontinuity's direction that develop to slope and is slope stability a wide use program for Stereographic Projection Method analysis that utilize geometrical correlation of stealing four sides and discontinuity surface. It is principle that angle of internal friction that is basis element of stability estimation applies direct shear test result on joint side, Examination is impossible by case execution, suppose by 30 angles that apply more conservatively in base rock slope sides usually and achieved analysis. When analyze, consider discontinuity's various adult that develop in research slope, after conduct first each discontinuity different assay falling into fault, joint, executed stability estimation which synthesize whole discontinuity data. When ailment element is recognized as analysis result, wished to present stability countermeasure way of most suitable to take into account of execution, stability, economic performance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1021-1024
• /
• 2001

Out of all metal-cutting processes, the hole-making process is the most widely used. It is estimated to be more than 30% of the total metal-cutting process. It is therefore desirable to monitor and detect drill wear during the hole-drilling process. In this paper, the vision system of the sensing methods of drill flank wear on the basis of image processing is used to detect the wear pattern by non-contact and direct method and get the reliable wear information about drill. In image processing of acquired image, median filter is applied for noise removal. The vision flank wear area of the drill was measured. Backpropagation neural networks (BPns) were used for no-line detection of drill wear. The neural network consisted of three layers: input, hidden and output. The input vectors comprised of spindle rotational speed, feed rates, vision flank wear, thrust and torque signals. The output was the drill wear state which was either usable or failure. Drilling experiments with various spindle rotational speed and feed rates were carried out. The learning process was peformed effectively by utilizing backpropagation. The detection of the abnormal states using BPNs achieved 96.4% reliability even when the spindle rotational speed and feedrate were changed.

• 소성∙가공
• /
• 제26권1호
• /
• pp.11-17
• /
• 2017

In this study, process analysis of elbow-shaped tubes using a mandrel has been performed. To reach the final shape within the dimensional tolerance, the process analysis has been performed at various processing parameters such as tube dimensions, the curved cutting surface and the radius of curvature. The area outside the boundary of the target shape was expressed as a quantitative index to analyze the formability. The validation experiments have also been performed in order to increase the reliability of the process analysis. For the processing of elbow-shaped tubes, it is preferable to make the angle of the portion where the punch touches the tube smaller than the opposite angle. And the convex cutting surface is advantageous due to the increased contacts between the punch and the tube ends during the bending process. Elbow tube having larger radius of curvature shows higher dimensional accuracy due to the relatively uniform strain distribution.

• 한국기계가공학회지
• /
• 제12권6호
• /
• pp.159-166
• /
• 2013

In order to develop the optimum shape of an MQL carbide end-mill suitable for high speed machining of wing ribs which are a detailed part of larger wing structures, using a new material Al-Li alloy, a new MQL carbide end-mill is created that has various quantities of holes, hole sizes, and hole locations. A theoretical machining graph is generated using the hammer test and FRF simulation, and a machining test is performed in order to verify the machining stability in the high speed machining area. The optimum configuration of the MQL carbide end-mill is also presented through comparing the chattering, machining noise and cutting conditions, including the maximum cutting depth, rpm, and feed rate per teeth, for each cutter.

• Current Photovoltaic Research
• /
• 제6권4호
• /
• pp.119-123
• /
• 2018

The High Performance Module With The Shingled String Has Several Advantages Such As The Larger Active Area, Higher Open-Circuit Voltage And Smaller Cell To Module (Ctm) Loss. To Obtain Increase Of Power In Pv Shingled Module, The Detailed Condition Of Various Parameters Related To Cutting And Bonding Process Were Investigated In This Study. We Searched The Optimized Cutting Conditions Of Laser Scan Speed, The Number Of Laser-Scribing And Also Bonding Conditions Of Electrically Conductive Adhesives (Eca) By Varying Amount Of Eca, Curing Time And Curing Temperature. The Shingled Pv Module Showed 25.4W of Maxmimum Power At 60 Rpm Of Dipensing Motor Speed, 30 Seconds Of Curing Time And $140^{\circ}C$ Of Curing Temperature, Respectively.

• 한국의류산업학회지
• /
• 제23권2호
• /
• pp.237-246
• /
• 2021

This study aims to analyze short sleeve cycling tops from three brands for a change in garment fit and pressure depending on the static and cycling postures. To this end, it used a 3D virtual garment system to virtualize the garments. Further, a cross-section of the 3D virtual garment data was obtained, and the space length was measured in the design-X program to prove the objectivity of the 3D virtual garment. The results indicated that three brands had a large space length at the front than the back because of the bent posture in cycling. Therefore, appropriate ease was required for the waist and abdomen. Although there were various cutting lines of the bodice panel by brand, the design of the cutting lines should consider the changes in the surface to reflect the bent posture in cycling. The results of this experiment confirmed that the wrinkles present in the 3D virtual garment were reflected in the cross-section and that the space length was small in the high-stress area, as shown in red. Therefore, it was proven the stress of the 3D virtual garment could be used for 3D virtual garment evaluation.

• 한국정밀공학회지
• /
• 제12권7호
• /
• pp.32-45
• /
• 1995

In this paper, we present a new method to tool path planning problem for rough cut of pocket milling operations. The key idea is to formulate the tool path problem into a TSP (Travelling Salesman Problem) so that the powerful neural network approach can be effectively applied. Specifically, our method is composed of three procedures: a) discretization of the pocket area into a finite number of tool points, b) neural network approach (called SOM-Self Organizing Map) for path finding, and c) postprocessing for path smoothing and feedrate adjustment. By the neural network procedure, an efficient tool path (in the sense of path length and tool retraction) can be robustly obtained for any arbitrary shaped pockets with many islands. In the postprocessing, a) the detailed shape of the path is fine tuned by eliminating sharp corners of the path segments, and b) any cross-overs between the path segments and islands. With the determined tool path, the feedrate adjustment is finally performed for legitimate motion without requiring excessive cutting forces. The validity and powerfulness of the algorithm is demonstrated through various computer simulations and real machining.

• 대한교통학회지
• /
• 제21권2호
• /
• pp.33-43
• /
• 2003

우리나라는 전 국토의 약 74%가 산지로 되어있어 도로건설에 따라 산지부 통과가 필연적이며, 이에 따라 터널이나 절토사면(절개면)과 같은 도로구간이 발생한다 절토사면의 경우, 전국 24개 노선 총 연장 900km에 대한 조사 결과에서는 약 2,400 개소의 절토사면이 있는 것으로 나타나 도로 1km당 평균 2.7개소의 많은 절토사면이 조성된 것으로 파악되었다. 도로의 절토사면은 붕괴사고 등과 같은 안전이 무엇보다 중요한 요소이나 도로의 질적수준 지향에 따라 운전자에게 쾌적한 도로경관도 점차 그 중요성이 부각되어 다양한 공법이 도입.적용되고 있고. 최근에는 도로설계단계에서 도로경관에 관한 수요와 요구가 급증하고 있다. 따라서 본 연구에서는 도로의 경관을 구성하는 중요한 요인중 하나인 절토사면을 대상으로 기존에 연구된 관련연구를 검토함과 동시에 실제로 현장에서 적용되고 있는 10개 공법별로 도로경관을 구성하는 핵심요소를 요인분석을 통하여 분석하여 경관구성의 결정요인을 파악하였다. 그리고 경관평가를 구성하는 정성적 특성을 반영하여 LISREL(공분산구조분석)모형을 구축하여 모형에 내재되어 있는 측정오차와 변수간의 관계를 파악함으로써 요인상호간의 관계를 고려한 경관평가와 분석이 가능하도록 하였다.

• 한국실내디자인학회논문집
• /
• 제23권3호
• /
• pp.21-28
• /
• 2014

The purpose of this study is to analysis the change of rural house type in Gyeongbuk province. There are 13 Gun(a kind of administrative district) areas in Gyeongbuk province. According to definition of rural area, the scopes of the research of rural houses limited the 12 places rural area(Gun area, excluded Ulleung-Gun) of Gyeongbuk province. The method of study is to compare and analyze about housing situation, structure of house, housing type and housing area etc. through the statistical data of each Gun area and other various data etc. during these 5 years. As a results of the analysis : 1) The supply ratio of housing is steadily decreasing in rural areas. 2) The houses of rural areas are changing from a detached house to multi-household house and small apartment by development near the rural area. 3) The number and area of commercial buildings are gradually increasing because of urbanization of rural areas. 4) The most houses inside area scopes in the rural area was from $60m^2$ to $85m^2$ area. And the family types of rural house are changing from large family to nuclear family and single households. 5) The structure of rural houses is changing from the brick house type to lightweight steel construction house because of cost-cutting of construction and easy way to construct etc.

• 한국초지조사료학회지
• /
• 제14권2호
• /
• pp.76-81
• /
• 1994

대관령 지역에서 Tall fescue 9개 품종을 공시하여 가을철 예취시기에 따른 2번초의 수량구성 요소와 개체중의 변화를 검토하여 이 지역의 환경조건에 적응성이 높은 품종을 선발하여고 하였으며, 얻어진 결과를 요약하면 다음과 같다. 1. 2번초에서 개체당 경수가 많은 품종(Barcel, Forager)이 개체중도 무거워서 이지역의 환경조건에 적응성이 높은 품종이라고 생각되었다. 2. 가을철 예취시기에 따른 2번초의 개체당 경수는 개체중과 0.1%의 유의한 정상관을 나타냈으나 1경중은 유의한 상관이 인정되지 않았다. 3. 2번초의 편균 개체중이 최대에 도달하는 가을철 예취시기는 $C_3$(10월28일)으로 추정되었다. 4. 2번초의 평균 개체중은 1번초의 평균 개체중과 반비례적인 관계를 나타내었다.