• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.455-465
• /
• 2006

In this study, the effect of scour was evaluated by regional and geotechnical characteristics and back data were accumulate for the design against scour through the local erosion characteristics evaluation of the Inchon coast. The erosion characteristics for the undisturbed soil samples collected near the main locations at the Incheon 2nd bridge, the Hwangyeong bridge, and a coast road in Songdo, are determined quantitatively through the scour rate tests. On the basic soil properties test, the bed around the Inchon coast chiefly consists of fined grained soils, and the soil samples were classified as silty clay(ML) or clay(CL) under the Unified Soil Classification System. On the scour rate test, the critical shear stress increases when the undrained shear strength increases as of the general trend of fine grained soils, and the average scour rate for the maximum velocity by 100 year flood is 173mm/hr at the Incheon 2nd bridge, 67mm/hr at the Hwangyeong bridge and 10mm/hr at a coast road in Songdo, respectively. Comparing to the scour rate of coarse grained soil, that of the bed around the Inchon coast is turned out to be very low. Therefore, the relative ability of the bed around the Inchon coast to resist erosion is assumed to be very high.

• Geotechnical Engineering
• /
• v.14 no.1
• /
• pp.81-92
• /
• 1998

Coal ash from thermal power plants has been produced in large quantity and discarded uselessly, However, it is possible to supply construction material properly by utilizing the coal ash as construction material. In this study, the applicable model and its applicability for deformation analysis of coal ash fill and reclamation ground are studied. Camflay model gives complete constitutive law which illustrates deformation and pore water pressure while soil is loaded under the various stresses at drained and undrained conditions. The merit of proposed model which is acquired from laboratory tests is that only a few soil parameters are available. The whole parameters of Camflay model are obtained by typical mechanical test and CV triaxial test on the sample with optimum mixing ratio( i.e. fly ash : bottom ash=5:5) Then the results from proposed numerical analysis are compared with laboratory results. The differences between laboratory test and numerical analysis are negligible. Parameters deter mined from laboratory tests are useful as a basic data for deformation analysis of coal ash reclamation ground using Camflay model.

• Geotechnical Engineering
• /
• v.10 no.4
• /
• pp.119-132
• /
• 1994

Undrained cyclic triaxial tests were performed on silt contained in the sand in order to investigate the effect of silt contents on the liquefaction strength and shear characterist ifs of the sand. As the result of this experiment, the weakest percentage of silt contained in the sand was 30% for all the relative density considered in the test. Also, the same bests were performed to find the effect of cyclic speed applied ranging from 0.1Hz to 5Hz on the liquefaction strength. The more the silt is contained in the sand, the greater the liquefaction strength was affected by cyclic speed, While the silt -containing sand was far less influenced by the cyclic speed than clay containing sand. These results are believed to be caused by the change of pore water pressure of the effective stress path.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.87-100
• /
• 1996

This paper verifies the accuracy and efficiency of the implicit stress integration algorithm for an anisotropic hardening constitutive model developed in a companion paper[Oh & Lee (1996)3. Simulation of undrained triaxial test results shows the accuracy of the method through an error estimation, and analyses of accuracy and convergence were performed for a numerical excavation problem. As a result, the stress was accurately integrated by the algorithm and the nonlinear solution was converged to be asymptotically quadratic. Furthermore nonlinear FE analysis of a real excavation problem was by performed considering the initial soil conditions and the in-situ construction sequences. The displacements of wall induced by excavation were more accurately estimated by the anisotropic hardening model than by the Cam-clay model.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.3
• /
• pp.93-100
• /
• 2015

The object of this paper is to study the shear characteristics of the weathered granite soil. To this end, a series of consolidated undrained triaxial compression tests are carried out to investigate the shear parameters-cohesion and internal friction angle-for the degree of saturation and degree of weathering. From the results, it is found that the shear parameters of weathered granite soil are influenced on the degree of saturation, degree of weathering and disturbance. Especially, internal friction angle is more influenced on the upper factors than cohesion. And shear parameters are more acted on the degree of saturation than the degree of weathering in the test range. It is, therefore, recommended that must be considered the conditions of granite soil-degree of saturation, degree of weathering and disturbance etc-in case of the calculation of bearing capacity, stability analysis and other designs with shear parameters.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.8 no.3
• /
• pp.33-42
• /
• 2005

The bearing methods using pile of steel itself or reinforced concrete has been applying which in excavated depth was not deep. Also, the retaining wall as resisting structure to lateral force has taken weakness that the cure periods of concreted is long. Recently, with the material cost of steel, the application of cement is more increasing trend. In this study, the design methods of earth retaining and retention wall within the pre-casted concrete pile, PHC(Pretentioned spun High strength Concrete piles), was proposed which in the ground condition of excavated depth was not deep. The typical ground conditions, cohesive and non-cohesive soil, was considered as follows; soil strength as internal friction angle and UU(Undrained Unconsolidation triaxial test) strength, soil reaction and stabilization of structures. The application of design methods could be confirmed through the comparing and analyzing between measured data and utility software for the design.

• Geotechnical Engineering
• /
• v.4 no.3
• /
• pp.43-52
• /
• 1988

The behavior of clays subjected to Repeated loading has been shown to be very different from the behavior under a single load application. Especially the behavior of pore water pressure is Qf considerable importance. The objective of this work is to experimentally study the stress-strain characteristics of clays, and this study includes the pore water pressure which is built up during the load repetition. For this study, the samples were consolidated isotropically in the triaxial cell during 24 hours, .and monotonic strain controlled triaxial test is carried out by uslng the tests of Compression failure, Cycled at failure, and Nonfailure equilibrium on remoulded samples under undrained .condition . Consequently there exists a critical level of repeated loading which seperates the behavior of a particular sample into two distinctly different patterns.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.131-142
• /
• 1999

The objective of this study is to perform finite element analyses using the anisotropic hardening constitutive model on the basis of the total stress concept. An anisotropic hardening constitutive model had been developed in a companion paper, and was then formulated by implicit stress integration and consistent tangent moduli. A nonlinear finite element analysis program was coded including the algorithm, and as a result, the nonlinear solution was accurately calculated and converged to be asymptotically quadratic. In the analysis of a test embankment it was found that the proposed model could predict the displacement of soils more reasonably than the analysis with von Mises type model. In addition the proposed model could predict accurately the actual behavior through the reanalysis of the problem by a reasonable evaluation of the strength parameter.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.235-244
• /
• 2001

Liquefaction may be caused by sudden decrease in the soil strength under undrained conditions. This loss of soil strength is related to the development of excess pore pressures. During this study, fines content affects the maximum and minimum void ratios are investigated. The results of static and cyclic triaxial test on silty saturated sands are presented. These tests are performed to evaluate liquefaction strength and static and cyclic behavior characteristics. The samples are obtained from Saemangeum and drying on air. The main results are summarized as follows : 1) The maximum and minimum void ratio lines follow similar trends. 2) Maximum and minimum void ratios are established at 20~30% fines content. 3) As confining pressures and overconsolidation ratio are increased, the resistance to liquefaction are increased. 4) Instability friction angles are increased with increasing initial relative density. 5) The resistance to liquefaction are decreased with increasing effective stress ratio.

• Journal of the Korean Society for Railway
• /
• v.8 no.4
• /
• pp.367-371
• /
• 2005

Pile foundations are utilized when soil is so weak that shallow foundations are not suitable or point load is concentrated in small area. Such soil can be formed by the land reclamation works which have extensively been executed along the coastal line of southern and western parts of the Korean Peninsula. The working load at pile is sometimes subjected to not only compression load but also lateral load sad uplift forces. But in most of the practice design, uplift capacity of pile foundation is not considered and estimation of uplift capacity is presumed on the compression skin friction. This study was carried out to determine that the effect of embedment ratio and loading rate on uplift adhesion factor of concrete pile driven in clay. Based on the test results, the critical embedment ratio is about 9. Adhesion factor is constant under the critical embedment ratio, and decreasing over the critical embedment ratio. Also, adhesion factor is increased with the loading rate is increased.