• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.613-623
• /
• 2012

In this paper, we present an ultra miniaturized voltage tuned oscillator, with HMIC-type amplifier and phase shifter, using LTCC artificial dielectric resonator. ADR which consists of periodic conductor patterns and stacked layers has a smaller size than a dielectric resonator. The design specification of ADR is obtained from the design goal of oscillator. The structure of the ADR with a stacked circular disk type is chosen. The resonance characteristic, physical dimension and stack number are analyzed. For miniaturization of ADRO, the ADR is internally implemented at the upper part of the LTCC substrate and the other circuits, which are amplifier and phase shifter are integrated at the bottom side respectively. The fabricated ADRO has ultra small size of $13{\times}13{\times}3mm^3$ and is a SMT type. The designed ADRO satisfies the open-loop oscillation condition at the design frequency. As a results, the oscillation frequency range is 2.025~2.108 GHz at a tuning voltage of 0~5 V. The phase noise is $-109{\pm}4$ dBc/Hz at 100 kHz offset frequency and the power is $6.8{\pm}0.2$ dBm. The power frequency tuning normalized figure of merit is -30.88 dB.

• Proceedings of the KIEE Conference
• /
• 2005.07a
• /
• pp.368-370
• /
• 2005

Due to the tendency towards large capacity and complexity of power system, an enhancement of power system equipment make a system impedance to be low in power system. Generally if an equivalent impedance of system becomes lower, a system stability will be better. But the fault current becomes very larger. The 345kV ultra-high voltage system will use current limit reactors(CLR) in a transmission line or a bus in substation to limit the magnitude of fault current. The CLR makes a significant contribution to the severity of the transient recovery voltage(TRV) experienced by feeder and bus circuit breakers on clearing feeder faults. Based on the conclusions of an investigation of actual circuit breaker failures while performing this duty, the mitigation of the transient recovery voltage associated with the reactors is described. Therefore in this article we simulated the TRV by EMTP at Bus Terminal Fault.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.12
• /
• pp.2136-2139
• /
• 2008

Chaotic oscillators can generate wide-band signals and the spectrum characteristics of the wide-band signals are not changed by switching on and off the output power of the oscillators. When communication systems use a chaotic oscillator, the communication system need not a local oscillator and a mixer used in conventional transceivers. Therefore the configuration of a communication system using a chaotic oscillator is simple and have the characteristics of low-power consumption. In this paper we design and implement a chaotic oscillator. And the test results of the implemented chaotic oscillator for UWB systems are presented. The implemented chaotic oscillator has -8.11dBm of the output power with 500MHz channel bandwidth at 3.4GHz of the center frequency and has about 410MHz of -10dB bandwidth.

• The Journal of the Korea Contents Association
• /
• v.7 no.1
• /
• pp.147-154
• /
• 2007

In this paper, we propose a new parallel search algorithm to acquire synchronization for UWB(Ultra Wideband) systems that reduces computation of the correlation. The conventional synchronization acquisition algorithms check all the possible signal phases simultaneously using multiple correlators. However it reduces the acquisition time, it makes high power consumption owing to increasing of correlation. The proposed algorithm divides the preamble signal to input the correlator into an m-bit bunch. We check the result of the correlation at first stage of an m-bit bunch data and predict whether it has some synchronization acquisition information or not. Thus, it eliminates the unnecessary operation and save the number of correlation. We evaluate the proposed algorithm under the AWGN and the multi-Path channel model with MATLAB. The proposed parallel search scheme reduces number of the correlation 65% on the AWGN and 20% on the multi-path fading channel.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.4
• /
• pp.35-40
• /
• 2002

Ultra-power-saving SBR has been fabricated by using vanadium and molybdenum with low work function. Because reverse leakage current is increased in inverse proportion to work function, we implanted argon ion on the n-Si layer for decreasing leakage current. The dose and acceleration energy of the argon implantation in the silicon was 1$\times$10$^{14}$ ion/$\textrm{cm}^2$, 40 keV, respectively. The forward voltages drop of fabricated V-SBR and Mo-SBR were 0.25 V and 0.39 V at the same forward current density of 60 A/$\textrm{cm}^2$. As a result, it was found that the reverse leakage current of the fabricated V-SBR was reduced over 20$mutextrm{A}$ by the argon implantation in comparison with the no implanted V-SBR. Also, owing to argon implantation, the inferiority of characteristic of the SBR was not detected.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.630-633
• /
• 2021

Microphones can convert received voice signals to electric signals. They have been widely used in various industries such as radios, smart devices and vehicles. Recently, the demands for small size and high sensitive microphones are increased according to the minimization of wireless earphone with the development of smart phone. A MEMS system is a good candidate for an ultra-small size microphone of a next generation and a read out IC for high sensitive MEMS sensor is researched from many industries and academies. Since the microphone system has a high sensitivity from environment noise and electric system noise, the system requires a low noise power supply and some low noise design techniques. In this paper, a low noise LDO is presented for small size MEMS microphone systems. The input supply voltage of the LDO is 1.5-3.6V, and the output voltage is 1.3V. Then, it can support to 5mA in the light load condition. The integrated output noise of proposed LDO form 20Hz to 20kHz is about 1.9uV. These post layout simulation results are performed with TSMC 0.18um CMOS technology and the size of layout is 325㎛ × 165㎛.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.6
• /
• pp.880-886
• /
• 2010

In this paper, we studied the application of low pressure ultra-violet (UV) lamps for the development of an energy saving ship's ballast water treat (BWT) device. We proposed the optimal arrangement of UV lamps by analyzing the energy radiated from medium- and low-pressure UV lamps. Based on the experimental results, we manufactured a disinfection chamber which is composed of low-pressure UV lamps. The rated power and the treatment capacity of the chamber are 216 [W] and 10 [$m^3$/h], respectively. This can replace a disinfection chamber treated by two 2 [kW] medium pressure lamps. The disinfection performance, however the power consumption is about one-eighteen compare to the medium pressure UV lamp, is over 94 [%] for bacteria, 93 [%] for zooplankton, and 94 [%] for phytoplankton. Therefore, it would be possible to develop an energy saving BWT device in a low capacity below 100 [$m^3$/h].

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.10
• /
• pp.1897-1904
• /
• 2006

Home service robot must recognize and build map for indoor and components of the house such as furniture and chair etc. The previous researcher has developed a indoor map building system by using CCD camera and ultra sonic sensor. %no stems have some problem in such a way that (1) a distun resolution can be changed according to the number of pixel when we use a CCD camera system, (2) a measured distance can be decreased when it transmitted to the rubber because of being absorbed the sound energy. This paper represents an intelligent sensor controller of module has been developed by using optic PSD(Position Sensitive Detector) sensor any at a low price. To deduce the switching noise from beam power module and diffused reflection noise, we proposed a heuristic soft filter. The performance of the developed system was compared with ultra sonic sensor system by detecting the indoor wall environment. Some experiments were illustrated for the validity of the developed system.

• Journal of Satellite, Information and Communications
• /
• v.12 no.1
• /
• pp.64-71
• /
• 2017

In this paper, Kalman filter and RRWA algorithm are used to estimate the accurate target in IR-UWB (Impulse-Radio Ultra Wideband) radar system, which enables accurate location recognition of indoors and outdoors with low cost and low power consumption. In the signal reflected by the target, unnecessary signals exist in addition to the target signal. We have tried to remove unnecessary signals and to derive accurate target signals and improve performance. The location of the targets is estimated in real time with one transmitting antenna and one receiving antenna. The Kalman filter was used to remove the background noise and the RRWA algorithm was used to remove the reflected signal. In this paper, we think that it will be useful to study the accurate distance estimation and tracking in future target estimation.

• Journal of IKEEE
• /
• v.15 no.4
• /
• pp.305-312
• /
• 2011

A primary interest of this work is to develop an efficient and powerful repetitive pulser system for the application of ultra wide band generation. The important component of the pulser system is a small-sized coaxial type spark gap with planar electrodes filled with SF6 gas. A repetitive switching action by the coaxial spark gap generates two consecutive pulses in less than a microsecond with rise times of a few hundred picoseconds (ps). A set of several parameters for the repetitive switching of the spark gap is required to be optimized in charging and discharging systems of the pulser. The parameters in the charging system include a circuit scheme, circuit elements, the applied voltage and current ratings from power supplies. The parameters in the discharging system include the spark gap geometry, electrode gap distance, gas type, gas pressure and the load. The characteristics of the spark gap discharge, such as breakdown voltage, output current pulse and recovery rate are too dynamic to control by switching continuously at a high pulse repetition rate (PRR). This leads to a low charging efficiency of the spark gap system. The breakthrough of the low charging efficiency is achieved by a parallel operation of two spark gaps system. The operational behavior of the two spark gaps system is presented in this paper. The work has focused on improvement of the charging efficiency by scaling the PRR of each spark gap in the two spark gaps system.