• Korean Journal of Optics and Photonics
• /
• v.7 no.3
• /
• pp.238-243
• /
• 1996

We have developed XeCl laser pumped double-resonator Dye laser and two-stage amplifier system, and generated simultaneously of alternatively two wavelengths suitable in DIAL system. The developed double-resonator is composed of 1st and 2nd diffraction orders on light incidence angle in grazing-incidence grating method with 1200 g/mm. We have obtained spectral linewidth below 10 pm and the total efficiency dependent on pump energy over 6%. The tuning ranges dependent on 1st and 2nd diffraction orders are 434~470 nm and 436~468 nm, respectively. The amplification gain and rine-450 dye laser by using the double-resonator laser system and measured the distribution of $NO_2$ concentration over Suwon as the result of transmission of laser output of 6 mJ in this DIAL system. Consequently, we have confirmed that the developed dye laser system is very useful as the tunable source for DIAL.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.5
• /
• pp.715-722
• /
• 2000

In this paper, the PLDRO is designed and implemented for X-band. It is comprised of tunable high Q resonator with a varactor diode for frequency tuning, loop filter and a 1/8 prescaler which up to 10GHz. Also, it is implemented a TCXO and a VCO signal into the phase detector and achieved a highly stable signal source. From the measurement, the designed PLDRO has the output power of 2.5dBm at 8GHz and phase noise of -64.33dBc at 10KHz offset from carrier. Its characteristic is 26 dBc. This PLDRO has much better temperature stability.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.5
• /
• pp.508-517
• /
• 2004

We described a near-field scanning microwave microscope which uses a high-quality dielectric resonator with a tunable screw. The operating frequency is f=4.5 5GHz. The probe tip is mounted in a cylindrical resonant cavity coupled to a dielectric resonator We developed a hybrid tip combining a reduced length of the tapered part with a small apex. In order to understand the function of the probe, we fabricated three different tips using a conventional chemical etching technique and observed three different NSMM images for patterened Cr films on glass substrates. We measured the reflection coefficient of different metal thin film samples with the same thickness of 300m and compared with theoretical impedance respectly. By tuning the tunable screw coming through the top cover, we could improve sensitivity, signal-to-noise ratio, and spatial resolution to better than $1{\mu}m$. To demonstrate the ability of local microwave characterization, the surface resistance of metallic thin films has been mapped.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.28-28
• /
• 2010

This study realized low-temperature crystallization process of the $Ba_{0.6}Sr_{0.4}TiO_3$ (BST) thin films without thermal damage of substrate using excimer laser annealing (ELA) and structural and electrical characteristics were investigated. The amorphous BST thin films were prepared on Pt/Ti/$SiO_2$/Si substrate by sol-gel method at $250^{\circ}C$. The ELA was carried out using KrF excimer laser which provided excitation wavelength of 248 nm. The beam homogenizing system was used in order to homogenize beam shape of Gaussian fit. The XRD and SEM were used to analyze structural characteristics and the microwave capacitance, dielectric loss and tunability of the BST films were measured by a symmetrical stripline resonator method with shorted end. Consequently, the crystallinity of BST thin films were improved after ELA process and RF tunable capacitor was demonstrated at low temperature below $300^{\circ}C$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.5
• /
• pp.506-513
• /
• 2015

In this paper, we proposed a novel ethanol concentration sensor using microfluidic metamaterial absorber. The metamaterial absorber comprises a split-ring-cross resonator(SRCR) and a microfluidic channel. The SRCR can generate LC resonance that is very sensitive to changes in the effective dielectric constant around the capacitive gap. In addition, microfluidic channels can change the effective dielectric constant of the dielectric substrate by using an infinitesimal quantity of a liquid on the order of microliters. The proposed absorber can detect the electrical properties of different concentration of ethanol. The performance of the proposed absorber is demonstrated using the absorption measurements of a fabricated prototype sample with waveguides. In addition, the simulated results and measurement results show good agreement.

• Progress in Superconductivity and Cryogenics
• /
• v.22 no.4
• /
• pp.10-13
• /
• 2020

High-quality superconducting coplanar waveguide (SCPW) resonators are crucial for developing superconducting quantum information devices and sensors. We designed quarter-wavelength SCPW resonators and fabricated the SCPW resonators using Nb thin film. The resonant characteristics were measured at T = 4.2 K, revealing the intrinsic quality factor and the coupling quality factor to be Qi = 4,784 and Qc = 17, 980, respectively. Our design and fabrication techniques would be very useful to develop a gate-tunable superconducting qubit based on the semiconductor nanostructures.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.174-179
• /
• 2013

This paper presents a capacitor loaded tunable bandpass chip filter using multiple split ring resonators (MSRRs) with two transmission zeros. To obtain high selectivity and minimize the chip size, asymmetric feed lines are adopted to make a pair of transmission zeros located on each side of passband. Compared with conventional filters using cross-coupling or source-load coupling techniques, the proposed filter uses only two resonators to achieve high selectivity through a pair of transmission zeros. In order to optimize selectivity and sensitivity (insertion loss) of the filter, the effect of the position of asymmetric feed line on transmission zeros and insertion loss is analyzed. The SOI-CMOS switched capacitor composed of metal-insulator-metal (MIM) capacitor and stacked-FETs is loaded at outer rings of MSRRs to tune passband frequency and handle high power signal up to +30 dBm. By turning on or off the gate of the transistors, the passband frequency can be shifted from 4GH to 5GHz. The proposed on-chip filter is implemented in 0.18-${\mu}m$ SOI CMOS technology that makes it possible to integrate high-Q passive devices and stacked-FETs. The designed filter shows miniaturized size of only $4mm{\times}2mm$ (i.e., $0.177{\lambda}g{\times}0.088{\lambda}g$), where ${\lambda}g$ denotes the guided wave length of the $50{\Omega}$ microstrip line at center frequency. The measured insertion loss (S21)is about 5.1dB and 6.9dB at 5.4GHz and 4.5GHz, respectively. The designed filter shows out-of-band rejection greater than 20dB at 500MHz offset from center frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.123-130
• /
• 2016

In this paper, a novel flexible microfluidic metamaterial absorber is proposed for remote chemical sensor applications. The proposed metamaterial absorber consists of a periodic of split-ring-cross resonators(SRCRs) and a microfluidic channel. The SRCR patterns are inkjet-printed using silver nanoparticle inks on paper. The microfluidic channels are laser-etched on polydimethylsiloxane(PDMS) material. The proposed absorber can detect change of the effective permittivity at different liquids. Therefore, the absorber can be used for a remote chemical sensor by detecting change of the resonant frequencies. The performance of the proposed absorber is demonstrated with full-wave simulation and measurement results. The experimental results shows that the resonant frequency is 10.49 GHz at the empty channel. When ethanol and DI-water are injected into the channel, the resonant frequencies are 10.04 GHz and 8.9 GHz, respectively.

• Clean Technology
• /
• v.22 no.3
• /
• pp.203-207
• /
• 2016

Here, we report a novel fabrication technique for patchable organic lasing sheet based on non-volatile liquid organic semiconductors and freestanding polymeric film with high flexibility and patchability. For this work, we have fabricated the second-order DFB grating structure, which leads to surface emission, embedded in the freestanding polymeric film. Using an ultra-violet (UV) curable polyurethaneacrylate (PUA) mixture, the periodic DFB grating structure can be easily prepared on the freestanding polymeric film via a simple UV curing process. Due to unsaturated acrylate remained in the PUA mixture after UV curing, the freestanding PUA film provides adhesive properties, which enable mounting of the patchable organic lasing sheet onto non-flat surfaces with conformal contact. To achieve laser actions in the freestanding resonator structure, a composite material of liquid 9-(2-ethylhexyl)carbazole (EHCz) and organic laser dyes was used as the laser medium. Since the degraded active materials can be easily refreshed by a simple injection of the liquid composite, such a non-volatile liquid organic semiconducting medium has degradation-free and recyclable characteristics in addition to other strong advantages including tunable optoelectronic responses, solvent-free processing, and ultimate mechanical flexibility and uniformity. Lasing properties of the patchable organic lasing sheet were also investigated after mounting onto non-flat surfaces, showing a mechanical tunability of laser emission under variable surface curvature. It is anticipated that these results will be applied to the development of various patchable optoelectronic applications for light-emitting displays, sensors and data communications.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.84-89
• /
• 1994

A tunable pulsed dye laser was operated in a single longitudinal mode by injection locking with a cw ring dye laser. A doubled Nd:YAG laser was used as the pumping source. Phase sensitive detection technique was applied to maintain the required match between the master laser frequency and the slave resonator cavity length. The fluctuation of the center frequency of the pulsed laser was < 10 MHz, and the pulse duration (FWHM) was 6 ns. The linewidth measured by scanning confocal interferometer was 130 MHz. When pumped by 50 mJ of the doubled Nd:YAG laser, the output energy of the pulsed dye laser was 2 mJ and the peak power was 330 kW. 30 kW.