• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.1
• /
• pp.71-84
• /
• 2007

Statement of problem: Implant surface characteristics plays an important role in clinical success and many studies have been made for improvement of success by changing surface roughness. Purpose: Appropriate increase of surface roughness increases the activity of osteoblast and enhance contact and retention between bone and implant. Material and method- Machined, SLA and RBM surface implants, which are the most commonly used implants were implanted into the tibia of rabbits and after 1 week, 4 weeks, 8 weeks and 12 weeks there were histologic and histomorphometric analysis and study for bone gradient and change of Ca/P ratio using EDS(Energy Dispersive X-ray Spectroscope). Results: Comparison of bone-implant contact showed no significant difference among each implant. In comparison of bone area rates, SLA showed higher value with significant difference at 1 week and 4 weeks, and SLA and RBM at 8 weeks than Machined implant (p<0.05). In analysis of bone constituents with EDS, titanium was specifically detected in new bones and the rates were constant by surface treatment method or period. In case of Ca/P ratio, according to surface treatment method, each group showed significant difference. Lots of old bone fragments produced during implantation remained on the rough surface of RBM implant surface and each group showed histological finding with active synthesis of collagen fibers until 12 weeks. In transmission electronic microscopic examination of sample slice after elapse of twelve weeks, tens nm of borderline (lamina limitans like dense line)was seen to contact the bone, on the interface between bone and implant. Conclusion: SLA and RBM implant with rough surface shows better histomorphometrical result and the trend of prolonged bone formation and maturation in comparison with Machined implant. In addition, implant with rough surface seems to be helpful in early stage bone formation due to remaining of old bone fragments produced in implantation. From the results above, it is considered to be better to use implant with rough surface in implantation.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.14 no.1
• /
• pp.40-48
• /
• 2011

The purpose of this study is to contribute enhancing the accuracy of viewshed analysis through the explanation for an analysis method of viewshed analysis using GIS. According to previous studies, the visible area using digital terrain in viewshed analysis depends on a visible interest area, scale of terrain, spatial resolution and surface data. In this study, we used trend analysis and RMSE analysis in order to find the effect of a visible interest area, scale of terrain, etc in viewshed analysis. Results of this study are as follows. First, the result of viewshed analysis depends on a visible interest area, scale of terrain, spatial resolution, surface data such as previous studies. Second, the results in forest area are reliable than those of flat area in terms of a visible interest area. Third, the results based on raster grid data are stable than those of TIN(triangulated irregular network) in terms of input surface data. Fourth, according to the result of trend and RMSE analysis, the spatial resolution for analysis is differently applied to different scales digital terrain map in viewshed analysis. In detail, it is desirable that the spatial resolution is set less than 10m(in the case of 1/1,000 digital terrain map), 20m(in the case of 1/5,000 map), 30m(1/25,000 map).

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.274-277
• /
• 2011

We measured a solar irradiation of vertical and horizontal surface per azimuth in southern area of Korea using pyrheliometer. In comparison with the provided data from ASHRAE and CIBSE, the average amount of solar irradiation has much variation of 10 to 150% in reference with north direction. In the clear day, the measured value has much difference with the value of ASHRAE and there is similar trend in case of CIBSE. The reason why amount of irradiation of clear day is differ from the average value, is able to be assumed that the value of ASHRAE and CIRSE is made of assumption based on clear days. The result of analysis of ASHRAE and CIBSE values according to the amount irradiation value for vertical and horizontal surface per azimuth using the MBE, RSME, and t-Statistic show that the CIBSE value has more reliability for the MBE, RMSE, and t-Statistic values than ASHRAE value.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.9 no.2
• /
• pp.59-64
• /
• 2003

The long­term trend and inter­relationship with depth of temperature and salinity in coastal waters of Korea are studied using coastal oceanographic observation and serial oceanographic data measured by National Fisheries Research and Development Institute. Temperature of coastal waters of Korea except south­western sea of Korea where cold water appears to increase in summer. In case of temperature offshore, surface temperature of East Sea increases, the reverse, for 50m and 100m decreases. Temperature in South Sea of Korea increases in whole depth and for the Yellow Sea, surface temperature increases, but for 50m decreases. In case of salinity offshore, surface salinity of East Sea decreases, but for 50m increases. Surface salinity in South Sea of Korea decreases, the reverse, form 50m and 100m increases. salinity in the Yellow Sea decrease in whole depth According to the result of inter­relationship analysis, for temperature relationship coefficients of 50m and 100m in the East Sea and South Sea of Korea is higher, however, for the Yellow sea the inter­relationship between 50m and 100m is lower. In case of salinity, the inter­relationship between surface and 50m, and for the South Sea of Korea, between 50m and 100m, and for the Yellow Sea, between surface and 50m is higher.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.539-545
• /
• 2009

KTX trains which began passenger service between Seoul and Busan in April 2004 have gained very high evaluation for their safe operation. Track is one of the most important means to keep KTX safety, it has not been a fail of safe structure. The track failure during operation may lead to a severe accident. So, it is to be verified the confidence of track maintenance management on the high speed line. This paper would like to find a track deformation trend through a comparative analysis on actual measurement data at these times. It discusses the effect of cyclic dynamic load at welding part. KTX dynamic impact load was measured in accordance with a rail surface irregularity and analyzed some track irregularities according to the condition of rail profile at welding part in the Gyeongbu high speed line.

• Geomechanics and Engineering
• /
• v.8 no.4
• /
• pp.511-521
• /
• 2015

It is a common failure type that high-filled embankment slope sideslips. The deformation mechanism and factors influencing the sideslip of embankment slope is the key to reduce the probability of this kind of engineering disaster. Taking Liujiawan high-filled embankment slope as an example, the deformation and failure characteristics of embankment slope and sheet-pile wall are studied, and the factors influencing instability are analyzed, then the correlation of deformation rate of the anti-slide plies and each factor is calculated with multivariate linear regression analysis. The result shows that: (1) The length of anchoring segment is not long enough, and displacement direction of embankment and retaining structure are perpendicular to the trend of the highway; (2) The length of the cantilever segment is so large that the active earth pressures behind the piles are very large. Additionally, the surface drainage is not smooth, which leads to form a potential sliding zone between bottom of the backfill and the primary surface; (3) The thickness of the backfill and the length of the anti-slide pile cantilever segment have positive correlation with the deformation whereas the thickness of anti-slide pile through mudstone has a negative correlation with the deformation. On the other hand the surface water is a little disadvantage on the embankment stability.

• Economic and Environmental Geology
• /
• v.13 no.3
• /
• pp.141-158
• /
• 1980

A geologic structure could be formed through various processes, because there are a number of factors which control the deformation of the Earth's crust. In geology, we could call it geological epistemology to describe exactly a geologic structure, and call it geological logics to infer logically the deforming process through which the geologic structure had been formed. Degree of legitimacy of geological logics depends upon the degree of exactness of geological epistemology. This study described quantitatively 3-dimensional Hambaek Syncline through computer analysis, and examined qualitatively into its deforming mechanism based on the results of 3-dimensional analysis of the structure. Input data for the computer analysis are dips and dip directions of bedding planes of the structure. The Hambaek Syncline disclose a minor fold group of NE-SW or NNE-SSW trend and a large scale fold of E-W trend. The conclusions of this study are as follows: (1) The fold of E-W trend is primary fold $(F_1)$ and the minor fold group of NE-SW or NNE-SSW trend secondary fold $(F_2)$. (2) Hambaek Syncline is cylindrical type fold. (3) Apparent axial trace of Hambaek syncline does not coincide with true axial trace. The apparent axial trace is $N70^{\circ}-80^{\circ}W$ in Gohan and Sabuk area, and changes to $N70^{\circ}-80^{\circ}E$ in the westward of the area, while the true axial trace is $N40^{\circ}-70^{\circ}W$ in the former, and $N60^{\circ}-80^{\circ}E$ in the latter area. (4) Westward dipping of axial plane of the minor fold group of NE-SW or NNE-SSW trend can be attributed to simple shear movements along overthrusts. (5) Angle between axial trace and the directional trace of the maximum principal compressive stress $({\sigma}_1)$ may not be perpendicular each other. The angle between them is governed by the following factors; 1) the plunge of fold axis 2) the dip of axial surface 3) cylindrisity (6) The mean axial trace of Hambaek Syncline $(F_1)$ is $N45.6^{\circ}W$, and the directional trace of ${\sigma}_1$ is $N52.4^{\circ}E$ (7) The mean axial trace of the minor fold group of NE-SW or NNE-SSW trend $(F_2)$ is $N21^{\circ}E$, and the directional trace of ${\sigma}_1$ is $N22^{\circ}W$.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2002.11a
• /
• pp.251-255
• /
• 2002

This paper describes the analysis of UHF signals taking place at partial discharges due to defects in GIS. To imitate the defects, two kinds of electrode were employed. One is to generate the PD due to corona discharge, and the other surface discharge. As a result, the magnitude of the UHF signals acquired from the discharges increased with the applied voltage. However, each frequency distribution trend at corona discharges and surface discharge was similar even though the applied voltage increased. Frequency distribution between corona discharge and surface discharge was clearly distinguish.

• Journal of the Korea Furniture Society
• /
• v.27 no.1
• /
• pp.35-42
• /
• 2016

With radical increase in one-person households, the consumption market in Korea has also rapidly changed. In line with this movement, customized furniture for sing lecustomershas been recently introduced. Since sleeping more than eight hours a day is needed to maintain a healthy lifestyle, a suitable bed for a comfortable sleep is an essential product for single consumers. In order to respond to this trend, a study was conducted to examine the surface materials of a bed designed for singles. A complete enumeration survey was implemented for beds manufactured by ACEBED Co., Ltd., Simmons-k, Co, Ltd,. Keumsung Bed, Hanssem Co,. Ltd., Hyundai Livart Co,. Ltd,. Emons Furniture Co,. Ltd,. and Borneo International Furniture Co., Ltd. This study helped in the proper selection of surface materials that may be used in the development of furniture for single consumers.

• Journal of Ginseng Research
• /
• v.18 no.1
• /
• pp.53-59
• /
• 1994

To develop the methodology of the quantitative analysis of saponin in ginseng milk, conditions of the saponin extraction were optimized using the fractional factorial design with 3 variables and 3 levels by a RSM computer program. The extraction of saponin increased with an increase in extraction temperature up to $90^{\circ}C$ and then decreased significantly at $100^{\circ}C$. Extraction time affected the saponin yield in a similar trend. On the other hand, decreasing cooling temperature increased the amount of the saponin extracted. Recovery yield of the saponin from ginseng milk varied from 70.0% to 92.9%. The optimum extraction temperature, time and cooling temperature determined by partial differentiation of the model equation were $86^{\circ}C$, 2.83 hrs and $4^{\circ}C$, respectively. Key words Ginseng milk, saponin, response surface methodology.