• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.6
• /
• pp.1422-1428
• /
• 2014

This paper has analyzed threshold voltage roll-off for bottom gate voltages of asymmetric double gate(DG) MOSFET. Since the asymmetric DGMOSFET is four terminal device to be able to separately bias for top and bottom gates, the bottom gate voltage influences on threshold voltage. It is, therefore, investigated how the threshold voltage roll-off known as short channel effects is reduced with bottom gate voltage. In the pursuit of this purpose, off-current model is presented in the subthreshold region, and the threshold voltage roll-off is observed for channel length and thickness with a parameter of bottom gate voltage as threshold voltage is defined by top gate voltage that off-currnt is $10^{-7}A/{\mu}m$ per channel width. As a result to observe the threshold voltage roll-off for bottom gate voltage using this model, we know the bottom gate voltage greatly influences on threshold voltage roll-off voltages, especially in the region of short channel length and thickness.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.86-93
• /
• 2009

Elastomeric O-rings have been the most common seals due to their excellent sealing capacity, and availability in costs and sizes. One of the critical applications of O-ring seals is solid rocket motor joint seal where the operating hot gas must be sealed during the combustion. This has long been a design issue to avoid the system failure. For laterally constrained, squeezed and pressurized condition, deformed shape of O-ring was measured by computed tomography method and CCD laser sensor, compared with numerical calculations. As clearance gap changes, sealing performance had been evaluated on peak contact stresses at top, bottom and side contact surfaces. As clearance gap increases, peak contact stresses and contact widths in top and side contact surfaces increase, and the asymmetry of stress distributions is promoted due to pressure increase. It is suggested that peak stress of bottom contact surface can be approximated by simple superposition of peak ones due to squeeze and pressure. Under pressurized condition, sealing performance is dependent on not peak stresses of bottom and side contact surfaces but that of top.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.7 no.1
• /
• pp.9-15
• /
• 2001

Top-to-bottom compression strength of corrugated fiberboard boxes is partly dependent on the load-carrying ability of the central panel areas. The ability of these central areas to resist bending under load will increase the stacking strength of the box. The difference of box compression strengths, among boxes which are made with identical dimensions and fabricated with same components but different flute sizes, is primarily due to difference of the flexural stiffness of the box panels. Top-to-bottom compression strength of a box is accurately predicted by flexural stiffness measurements and the edge crush test of the combined boards. This study was carried out to analyze the flexural stiffness, maximum bending force and maximum deflection for various corrugated fiberboards by experimental investigation. There were significant differences between the machine direction (MD) and the cross-machine direction (CD) of corrugated fiberboards tested. It was about 50% in SW and DW, and $62%{\sim}74%$ in dual-medium corrugated fiberboards(e.g. DM, DMA and DMB), respectively. There were no significant differences of maximum deflection in machine direction among the tested fiberboards but, in cross direction, DM showed the highest value and followed by SW, DMA, DMB and DW in order. For the corrugated fiberboards tested, flexural stiffness in machine direction is about $29%{\sim}48%$ larger than cross direction, and difference of flexural stiffness between the two direction is the lowest in DMA and DMB.

• Journal of Korea Multimedia Society
• /
• v.15 no.7
• /
• pp.941-950
• /
• 2012

A virtual garment fitting system which fits the top and bottom of a garment on 3D body data is introduced. This system uses the laser scanned 3D body data and the digital images photographed the front and back of a garment. The digital images are modeled to reflect tensions among particles in the images and the friction and gravity effects are considered in the fitting process to the body data. When a bottom is fitted, a virtual belt to hold the bottom in the waist is introduced since gravity effects pull down it. Also the process for fitting the top and bottom on layers is proposed here. The system has the strengths that it uses only the front and back image of a garment instead of using complicated patterns of a garment, and provides a realistic fit result as a 3D figure. As on-line retailing shop in present displays front and back images of garments, this system also does. However this system provides a differentiated service to user than present retailing shop as showing a 3D fit image. It will make a new trend in online shop retailing of garment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.2
• /
• pp.401-406
• /
• 2015

The change of subthreshold swing for channel length of asymmetric double gate(DG) MOSFET has been analyzed. The subthreshold swing is the important factor to determine digital chracteristics of transistor and is degraded with reduction of channel. The subthreshold swing for channel length of the DGMOSFET developed to solve this problem is investigated for channel thickness, oxide thickness, top and bottom gate voltage and doping concentration. Especially the subthreshold swing for asymmetric DGMOSFET to be able to be fabricated with different top and bottom gate structure is investigated in detail for bottom gate voltage and bottom oxide thickness. To obtain the analytical subthreshold swing, the analytical potential distribution is derived from Possion's equation, and Gaussian distribution function is used as doping profile. As a result, subthreshold swing is sensitively changed according to top and bottom gate voltage, channel doping concentration and channel dimension.

• Archives of Craniofacial Surgery
• /
• v.19 no.1
• /
• pp.1-2
• /
• 2018

Theoretically, panfacial bone fractures involve all three areas of the face: frontal bone, midface, and mandible. In practice, when two out of these three areas are involved, the term "panfacial bone fracture" has been applied. We can use physical examination, simple radiologic examination, and computed tomography study for diagnosis. Linear fracture are treated by conservative treatment. But, most of panfacial bone fracture patients need to be treated by open reduction and internal fixation. Facial width is most important thing that we need to care during operation. There are many ways about sequence like "top to bottom," "bottom to top," "outside to inside," or "inside to outside" and the authors prefer "top to bottom" and "outside to inside" ways. The authors apply arch bar from the first of surgery and then, set frontal bone fracture, midface fracture and mandible fracture in sequence. Usually, we remove the stitches for 5 days after surgery and the intraoral stitch removed after 2 weeks. Usually arch bar is going to be removed 4 weeks after surgery. We could get acceptable results with the above way.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.179-183
• /
• 2000

For a ground plane in high-temperature superconducting ramp-edge junction devices, YBa$_2$Cu$_3$O$_{7-{\delta}}$/SrTiO$_3$/YBa$_2$Cu$_3$O$_{7-{\delta}}$ multilayer structures were fabricated using pulsed laser deposition and ECR ion milling. Various process parameters were adjusted to enhance the device characteristics. By etching the STO layer to form a tapered edge of about 15$^{\circ}$ and in-situ RF plasma treatment of bottom YBCO surface prior to deposition of top YBCO, the top-to-bottom YBCO showed T$_c$ of 75${\sim}$80 K and I$_c$ of about 40 mA through holes. It was found that the deposition of bottom YBCO at a reduced laser repetition rate of 1Hz increased the T$_c$ of top YBCO to 79.9 K. The resistivity of 570 layer was about 10$^6$ ${\Omega}$cm at 60 K, which ensures good electrical isolation between successive YBCO layers.

• Journal of Power System Engineering
• /
• v.15 no.1
• /
• pp.45-50
• /
• 2011

The effect of Mn and Ti contents in filler wire on the microstructure and mechanical property of weld metal has been investigated after hybrid welding with ultra fine grained (UFG) steel. The microstructure and distribution of alloy compositions at the top region of weld zone were quite different with those at the bottom region after hybrid welding. The bottom region of weld zone contained higher Mn and Ti contents, and consequently the hardness of bottom region was higher than that of top region. With the increase of Mn and Ti contents in filler wire, the volume percent of acicular ferrite in weld metal decreased, and the weld zone showed higher hardness and better impact property.

• Journal of Korean Society of Rural Planning
• /
• v.23 no.4
• /
• pp.111-126
• /
• 2017

This study analyzes the impacts of agricultural water shortages in Korea using a combined top-down and bottom-up model. A multi-region multi-output agricultural sector model with detailed descriptions of production technologies and water and land resource constraints has been combined with a standard CGE model. The impacts of four different water shortage scenarios were simulated. It is shown that an active adaptation of crop choices occurs in even the regions with relatively abundant water resources in order to respond to the change in relative output prices caused by water shortages. We found that although the losses in production values are not quite large despite water shortages due to the price feedbacks, the loss in GDP is substantial. We show that our combined approach has advantages in deriving region and product specific production effects as well as the overall GDP loss effect of water shortages.

• New & Renewable Energy
• /
• v.3 no.1 s.9
• /
• pp.75-82
• /
• 2007

Aluminum was used as metallic bipolar plate material to reduce a stack weight. The functional materials such as conductive material, Au and nonconductive material, PTFE [polytetrafluoroethylene] were coated on the bipolar plate to enhance electrical contact and corrosion prevention in PEMFC. The active area of bipolar plate is divided into the top layer part that electric current mainly passes, and the bottom layer part that gas and water pass. The bottom layer part in the flow channel needs not to have electrical conductivity because it doesn't pass electric current directly. In this reason, Au on the top layer and PTFE on the bottom layer were coated to apply high electrical conductivity and/or good corrosion resistance. Although the single cell performance using Au-PTFE/Al bipolar plate was shown 78% in comparison with that of graphite, specific power of Au-PTFE/Al bipolar plate(0.4 W/g) was twice as much as graphite bipolar plate.