• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.7-14
• /
• 2009

In this paper, the effects of annealing conditions on the structural ((002) intensity, FWHM, d-spacing, grain size, (002) peak position), optical (UV peak, UV peak position) and electrical properties (carrier concentrations, resistivity, mobility) of ZnO films were investigated. ZnO films were deposited onto SiO$_2$/si substrates by RF magnetron sputtering from a ZnO target. The substrate was not heated during deposition. ZnO films were annealed in temperature ranges of $500\sim650^{\circ}C$ in the O$_2$ flow for 5$\sim$20 min. The film average thicknesses were in the range of 291 nm. The surface morphologies and structures of the samples were characterize by SEM and XRD, respectively. The optical properties were evaluated by photoluminescence (PL) measurement at room temperature (RT) using a He-Cd 325 nm laser. As the annealing temperature and time vary, the following relations were also observed: (1) proportional relationships among UV intensity (002) intensity, and grain size exist, (2) UV intensity is inversely proportional to FWHM, (3) there is no special relationship between UV intensity and electron carrier concentrations, (4) d-spacing is inversely proportional to (002) peak position, (5) UV peak position in the range of 3.20$\sim$3.24 eV means that ZnO films have a n-type conductivity which was consistent with that obtained from the electrical property, (6) the optimal conditions for the best optical and structural characteristics were found to be oxygen fraction, (O$_2$/(O$_2$+Ar)) of 0.2, RF power of 240W, substrate temperature of RT, annealing condition of 600$^{\circ}C$ for 20 min, and sputtering pressure of 20 mTorr.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.552-558
• /
• 2014

This paper suggests how to design a ZigBee-chip-based communication module to remotely measure radiation level. The suggested communication module consists of two control processors for the chip as generally required to configure a ZigBee system, and one chip module to configure a ZigBee RF device. The ZigBee-chip-based communication module for remote radiation measurement consists of a wireless communication controller; sensor and high-voltage generator; charger and power supply circuit; wired communication part; and RF circuit and antenna. The wireless communication controller is to control wireless communication for ZigBee and to measure radiation level remotely. The sensor and high-voltage generator generates 500 V in two consecutive series to amplify and filter pulses of radiation detected by G-M Tube. The charger and power supply circuit part is to charge lithium-ion battery and supply power to one-chip processors. The wired communication part serves as a RS-485/422 interface to enable USB interface and wired remote communication for interfacing with PC and debugging. RF circuit and antenna applies an RLC passive component for chip antenna to configure BALUN and antenna impedance matching circuit, allowing wireless communication. After configuring the ZigBee-chip-based communication module, tests were conducted to measure radiation level remotely: data were successfully transmitted in 10-meter and 100-meter distances, measuring radiation level in a remote condition. The communication module allows an environment where radiation level can be remotely measured in an economically beneficial way as it not only consumes less electricity but also costs less. By securing linearity of a radiation measuring device and by minimizing the device itself, it is possible to set up an environment where radiation can be measured in a reliable manner, and radiation level is monitored real-time.

• Journal of Environmental Health Sciences
• /
• v.18 no.2
• /
• pp.3-18
• /
• 1992

This research was carried out on 1,017 production workers for four months from May to August, 1991, to search more effective management method of their health by grasping their knowledge and attitude on industrial health. The results of this study can be summarized as follows: 1. As for general characteristics, 74.2% were male and 25.8% were female among the 1,017 workers. The two largest age groups were 30~39, 38.7%. As for education level, graduation from high school was 58.6%, 61.2% were married, 35.9% owned their house, and workers who worked more than 1 year less than 5 years was 52.9%, workers who worked 8 hours a day was 46.7%, the largest group income level was 60~69 thousand won 21.2%, and the degree of satisfaction with work was ordinary, 45.6%. 2. The degree of recognition concerning occupational diseases was 92.5% at a very high rate. Causes of occupational diseases under the present work field were in order of noise, dust, heavy metal. The largest group of the counterplan for prevention was an improvement of working environment, 62.0%. 3. The major cause that threatens worker's health was poor working environment, 31.4%. As the best method for workers' health management, working environment management was pointed. 4. As for health examination result, the response that it is of use to health management was 53.8%. As for examination method and result, 42.7% responded that they are formal. The practice period was more than once every six months as the largest group, and the highest desire for improvement was that they wants an exact information of the result. 5. 49.3% of the respondents know about the measurement of working environment an the response that the measurement is necessary to improve working environment was 57.9%, and that the results from the measurement were reflected on improvement an management 57.5%. Appropriate period to take a measurement was more than once per six months, 40.2% and per three months, 29.1%. 6. As for safety and halth instruction, 34.5% were educated for both, 38.2% for only safety education and just 4.6% for only health education. 51.9% responded that they had never been educated out of work place. The period of its practice was more than once a month, 39.5% and every three months, 21.3%. 7. The importance of safety and health showed that the one is equal to the other, 59.8%, that the one is more important, 29.6%, and that other is more important, 7.6%. 67.7% said the necessity of a safety and health manager. 8. In spite of more or less health obstacle of work environment, 14.9% of the respondents wanted to overwork to gain an allowance for over-time work, 39.9% didn't, and 40.2% according to condition and state. 9. As the most important cause of industrial accident, 40.2% indicated unsafe behavior. As for the individual protective instrument, 66.1% of all the respondents said they have worn it to protect industrial diseases. 10. As for the degree of understanding of the contents in Industrial Safety and Health Law and Industrial Law of Accident Insurance, an affirmative response was respectively 49.3% and 50.8% and the sources of safety-health information were televisions and radios, 28.0%. Therefore, it is necessary that we do positive working environmental improvement, continuous management and health education's inforcement to increase their health and prevent occupational diseases.

• Journal of the Korean earth science society
• /
• v.33 no.4
• /
• pp.329-336
• /
• 2012

In September 2009, a perfectly preserved fossil of a dinosaur egg nest was discovered in the Cretaceous formations of the Aphaedo area in Shinan, Jeollanam-do, South Korea. In order to estimate the age of dinosaur eggshells and the depositional age of the Cretaceous sediments in Aphaedo area, a whole-rock K-Ar dating was carried out on volcanic pebbles showing a sedimentary structure contemporaneous with the Aphaedo strata, acidic tuffs overlaying the strata conformably, and acidic dike rocks intrude to both of them. Volcanic rocks observed in the strata are 3-20 cm in diameter as pebbles found in lenticular conglomerate and pebble bearing mudstone strata. K-Ar whole-rock dating was performed on six different volcanic pebbles which show a sedimentary structure contemporaneous with the dinosaur egg nest contained in the strata, and all samples show Late Cretaceous ages: Cenomanian ($97.6{\pm}1.9$Ma), Coniacian ($87.6{\pm}1.7$ Ma), Santonian ($84.5{\pm}1.7$Ma) or Campanian ($82.5{\pm}1.6$, $77.3{\pm}1.5$, $75.7{\pm}1.5$ Ma). The K-Ar whole-rock age of acidic tuffs overlaying the Cretaceous formation conformably was estimated to be Campanian ($79.2{\pm}1.6$ or $77.3{\pm}1.5$Ma), when the dating was carried out under the same conditions. The acidic dike intruding both Cretaceous formation and acidic tuff showed a K-Ar whole-rock age of $70.9{\pm}1.4$Ma (Campanian). Therefore, the depositional age of the Cretaceous formation in the Aphaedo area and the time when dinosaurs lived in the study area are considered to be 77-83 Ma. Such results indicate that the ages of dinosaur eggshells from Aphaedo area can be correlated with the ages of the Seonso Formation (81Ma) with dinosaur egg nest fossils and the Uhangri Formation (79-81Ma) with dinosaur, pterosaur and web-footed bird tracks.

• Journal of Korean Home Economics Education Association
• /
• v.24 no.1
• /
• pp.21-36
• /
• 2012

The purpose of this study was to determine the direction of dietary education in school. A questionnaire that identified nutrition knowledge, dietary behavior, help degree to real-life of dietary education, and dietary education satisfaction were developed based on a review of the literature. The subjects consisted of 409 high school female students in Daegu and Gyeongbuk area. The total mean score of nutrition knowledge was 9.2/15.0. The score of nutrition knowledge was correlated with school type, grade, number of brothers and sisters, and school record(p<0.05). The dietary behavior was 3.30/5.00, showing difference from school type, father's occupation, and economic level(p<0.05). It was also found that the higher the score in nutrition knowledge, the higher the score in dietary behavior(p<0.001). The total mean score of the dietary education satisfaction and help degree to real-life of dietary education for high school female students were same as 3.39/5.00. The biggest reason of unsatisfaction on dietary education was lack of class time. The form of instruction they want to get was the class for experiment and practice. The score of the dietary education satisfaction was correlated with help degree to real-life of dietary education, nutrition knowledge, and dietary behavior(p<0.01). Therefore, more active dietary education should be give to high school female students to meet the intellectual need and successful dietary behavior. Also dietary education would be needed to relate with their home.

• Korea Journal of Hospital Management
• /
• v.3 no.1
• /
• pp.1-33
• /
• 1998

The purpose of this thesis is to study theoretical access to the methods that have been used for the research of occupational stress, thereby providing management methods of occupational stress of hospital workers. With a stress model of hospital workers set up from the viewpoint of organization management, 929 sets of questionnaires were collected from intern doctors, resident doctors, nurses, nursing aides, pharmacists, medical technicians, workers in patient affairs(reception and medical insurance workers), administrators and clerks from the 8 hospitals in Seoul with more than 500 beds. Upon variance analysis, correlation analysis and regression analysis of the collected questionnaires, this work examined how differences in stress caused by specific occupations and formulated a method of stress management for the hospital workers. The results are as follows. 1) If some duties of the nurses suffering from role-overloaded stress are transferred to the nursing aides dissatisfied with insufficient role, the two grunting groups can be satisfied at the same time. It is also necessary to transfer some jobs of the overloaded workers in patient affairs to the administrators, or the other way around. To reduce stress of conflict and ambiguity of role caused by the obscure division of roles between the workers, the role of each occupation should be delineated and the clear division of roles should be translated into action strictly according to that delineated. 2) Stress of inefficiency of organization from which the student doctors suffer can be relieved by management of participation. If they have access to the process of decision-making in general hospital affairs and consequently their understanding and the autonomy of job performance are promoted, such stress will be reduced. 3) To cope with stress of career development from which nurses, medical technicians, administrators, workers in patient affairs suffer, it is necessary to establish whether they have a chance to revive their careers, whether there are any ways of remotivation for less contributive workers, and whether they encourage each other to develope their careers. If they are given a chance to develope their careers, such stress will be relieved. 4) Pharmacists, suffering from stresses of living and personal relations, have strong cohesive power among themselves and organize a well-integrated team; thereby reducing the stress of personal relations and increasing productivity. 5) For administrators and student doctors confined to lesser social supports and for nurses and workers in patient affairs whose recognition of stress and job satisfaction are affected by social supports, emotional and informational supports for job performance help alleviate an individual's mental, and physical stress. 6) In addition to the above-mentioned stress-management methods, if an organizational coping strategy is provided according to the types of stress from the general viewpoint of the whole group of hospital workers, it would be of great help to managing stress. For example, the redesign of jobs, the management of objective, the improvement of working environment, the formation of an autonomous working group and various working plans can be set up for those who suffer from stress related to inappropriate role, while career counseling and development of career process can be provided for those dissatisfied with career development. Participation in the process of decision-making and the restructuring of the organization are needed for those who suffer from stress of malfunctioning organization, whereas creation of a supportive organizational atmosphere is desired for those who feel stressed due to personal relations. As well, such organizational coping strategies. as the increase of welfare facilities, seminars and educational programs and provision of health-promotion facilities can be provided.

• The Journal of Korean Academy of Prosthodontics
• /
• v.51 no.1
• /
• pp.11-19
• /
• 2013

Purpose: The aim of this study was to evaluate the heat generation in bone in vitro during the guided flapless drilling procedure and the effect of drilling methods on the heat generation. Materials and methods: A model that has missing the first and second mandibular molars bilaterally was used. In group A, classical flap implant surgery was performed. In group B, flapless implant surgery using surgical guide was performed. In group C, flapless implant surgery using surgical guide without up-and-down pumping motion was performed. Temperature was measured with k-type thermocouple and a real-time digital thermometer. The thermocouples were placed at 0.5 mm away from the osteotomy area at the depths of 3 mm and 6 mm. The measured values were evaluated with independent t-test. Results: The mean temperature generated was $27.2^{\circ}C$ ($SD{\pm}2.1^{\circ}C$) and $27.5^{\circ}C$ ($SD{\pm}2.3^{\circ}C$) for groups A and B, respectively. These differences were not statistically significant. In group C, the mean temperature was $37.0^{\circ}C$ ($SD{\pm}3.4^{\circ}C$). There were statistically significant differences between groups B and C with respect to the mean temperature. Conclusion: These findings suggest that guided flapless drilling with up-and-down pumping motion may not significantly increase the bone temperature.

• Journal of Periodontal and Implant Science
• /
• v.37 no.sup2
• /
• pp.447-463
• /
• 2007

Periodontal ligament (PDL) cells have been known as multipotential cells, and as playing an important rolesin periodontal regeneration. The PDL cells are composed of heterogeneous cell populations which have the capacity to differentiate into either cementoblasts or osteoblasts, depending on needs and conditions. Therefore, PDL cells have the capacity to produce mineralized nodules in vitro in mineralization medium which include ascorbic acid, ${\beta}$-glycerophosphate and dexamethasone. In spite of these well-known osteoblast like properties of PDL cells, very little is known about the molecules involved in the formation of the mineralized nodules in the PDL cells. In the present study, we analysed gene-expression profiles during the mineralization process of cultured PDL cells by means of a cDNA microarray consisting of 3063 genes. Nodules of mineralized matrix were strongly stained with alizarin red S on the PDL cells cultured in the media with mineralization supplements. Among 3,063 genes analyzed, 35 were up-regulated more than two-fold at one or more time points in cells that developed matrix mineralization nodules, and 38 were down-regulated to less than half their normal level of expression. In accord with the morphological change we observed, several genes related to calcium-related or mineral metabolism were induced in PDL cells during osteogenesis, such as IGF-II and IGFBP-2. Proteogycan 1, fibulin-5, keratin 5, ,${\beta}$-actin, ${\alpha}$-smooth muscle actin and capping protein, and cytoskeleton and extracellular matrix proteins were up-regulated during mineralization. Several genes encoding proteins related to apoptosis weredifferentially expressed in PDL cells cultured in the medium containing mineralization supplements. Dkk-I and Nip3, which are apoptosis-inducing agents, were up-regulated, and Btf and TAXlBP1, which have an anti-apoptosis activity, were down-regulated during mineralization. Also periostin and S100 calciumbinding protein A4 were down-regulated during mineralization.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.3
• /
• pp.471-479
• /
• 2001

The purpose of this study was to compare the effect of the high intensity halogen light $(850\sim1000mW/cm^2)$ with that of the conventional halogen light $(400mW/cm^2)$ on the hardness of composite resin. Three resin composites (Z-100, 3M, U.S.A. : Tetric Ceram, Vivadent, Liechtenstein; SureFil, Dentsply, U.S.A.) were filed in the stainless steel moulds which were 4mm in diameter and 2, 3, 4, and 5mm in depth, respectively. They were cured under the four different modes : (1) conventional mode, 40 seconds at $400mW/cm^2$; (2) 'ramp' mode, 10 seconds at 100 to $1000mW/cm^2$ plus 10 seconds at $1000mW/cm^2$; (3) 'boost' mode, 10 seconds at $1000mW/cm^2$; and (4) 'standard' mode, 20 seconds at $850mW/cm^2$. The surface hardnesses of the top and the bottom of the resin samples were measured with a microhardness tester (MXT70, Matsuzawa, Japan). The top surface hardness was not significantly different among the curing modes. The bottom surface hardness was generally the highest in the conventional mode and the lowest in the high intensity boost mode. There was no significant difference in the bottom surface hardness between the conventional mode and the high intensity standard mode in 2mm depth. The results suggest that the curing time of the high intensity halogen light $(850mW/cm^2)$ should be at least 20 seconds to produce the equal level of the bottom surface hardness of 2mm resin composite as compared to the hardness produced by the conventional halogen light $(400mW/cm^2)$.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.2
• /
• pp.254-262
• /
• 2003

Dental caries has a multifactorial aetiology in which there is an interplay of three principal factors: the host(saliva and teeth), the microflora(dental plaque) and the substrate(diet), and a fourth factor time. There is no single test that takes into consideration all these factors and can accurately predict an individual's susceptibility to dental caries. The risk of dental caries can be evaluated by analysing and integrating several causative factors. The objective of the study was to clarify the relationship between caries activity and the status of caries of primary teeth and the relationship between the quantity of S. mutans in the dental plaque and the status of dental caries. Forty nine children ages 5 were examined with caries indices, Dentocult-SM and quantity of S. mutans. The results were as follows: All the survey results were similar with national means of 5-6 years Korean preschool children. The deft index of subjects was 5.46 and defs index was 9.81. There was 8.6% of negative, 10.9% of mild, 28.1% of moderate and 52.3% of active results at screening strip test. 8.6% was negative, 17.2% was mild, 33.6% was moderate and 40.6% was active in site strip test. The Spearman correlation coefficient was 0.775, and overall kappa index was 0.496 between screening strip test and site strip test. There also was a high correlation between caries incidence, Dentocult-SM test, and quantity of S. mutans. Dentocult-SM test as a caries activity test is a reliable method for measuring the status of dental caries in primary teeth.