• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.40-45
• /
• 2011

Design and fabrication of a TCRR (Triple-coupler Ring Resonator) filter which can provide a doubled FSR (Free Spectral Range) compared with a conventional DCRR (Double-coupler Ring Resonator) filter, are discussed. Through the use of a polymer material with a good thermo-optic property and with high contrast between core and cladding polymer, a compact TCRR filter composed of straight and curved buried waveguides of small radius is designed and fabricated. The transmission characteristics from the through and drop ports are measured using a tunable laser and a fiber array block, and the FSR is observed to be 4.4 nm, about twice that of DCRR filter, and almost the same as that obtained from the analysis using a transfer matrix method.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.10
• /
• pp.51-56
• /
• 2004

We propose and fabricate an 1${\times}$2 asymmetric optical switch by TOE using SOI wafer based on silicon which has very large TOE figure and it is a good material for optical devices. SOI wafer consists of 3 layers; upper Si layer for device(waveguide;core, n=3.5), buried oxide layer for insulator(clad, n=1.5) and Si substrate layer. We designed 1${\times}$2 asymmetric y-branched single mode optical waveguide switch by BPM simulation and metal heater by heat transfer simulation. Fabricated switch shows about 3.5 watts of power consumption and over 20dB of crosstalk between output channels.

• Current Optics and Photonics
• /
• v.3 no.5
• /
• pp.401-407
• /
• 2019

Polymeric optical waveguide devices with Bragg gratings have been investigated, for implementing tunable lasers and wavelength filters used in wavelength-division-multiplexed optical communication systems. Owing to the excellent thermo-optic effect of these polymers, wavelength tuning is possible over a wide range, which is difficult to achieve using other optical materials. In this study the phase-mask technology, which has advantages over the conventional interferometeric method, was introduced to facilitate the fabrication of Bragg gratings in polymeric optical waveguide devices. An optical setup capable of fabricating multiple Bragg gratings simultaneously on a 4-inch silicon wafer was constructed, using a 442-nm laser and phase mask. During fabrication, some of the diffracted light in the phase mask was totally reflected inside the mask, which affected the quality of the Bragg grating adversely, so experiments were conducted to solve this issue. To verify grating uniformity, two types of wavelength-filtering devices were fabricated using the phase-mask lithography, and their reflection and transmission spectra were measured. From the results, we confirmed that the phase-mask method provides good uniformity, and may be applied for mass production of polymer Bragg-grating waveguide devices.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.475-479
• /
• 2006

An integrated photonic K-band microwave bandpass filter has been proposed and demonstrated by incorporating a polymeric ring resonator. Its transfer characteristics were adjusted by shilling the resonance wavelength of the ring resonator via the thermooptic effect. The achieved performance of the filter includes the center frequency of 20 GHz, the attenuation of ${\sim}15dB$, the bandwidth of 2 GHz, and the corresponding quality factor of 10. The microwave output power within the passband of the device was adjusted at the rate of about 6.7 dB/mW in the range of 27 dB. This kind of device with electrically controllable transfer characteristics can be applied to implement microwave switches and other devices.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1220-1225
• /
• 2009

In this paper, a tunable fiber feedback laser based on the use of Sagnac loop filter and fiber Bragg grating (FBG) is proposed. The Sagnac loop filter using a high birefringence fiber provides precise 0.33-nm channel spacing as a multi-wavelength grid filter. Ni-Cr wire wound on the FBG is useful to induce the thermo-optic effect of the fiber. Two types of FBG structures, which have a different length of wire, are demonstrated to show the wavelength shift and separation. To tune FBG by resistant heat, some current is supplied into the wire. When the wavelength matched with one of the cavity modes of Sagnac loop filter, the mode-locked lasing is occurred. The electrical power sensitivity of the resonant wavelength is measured to 1.75pm/mW. This laser configuration can be applied the electrical power system for monitoring the power fluctuation.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.254-260
• /
• 2005

By incorporating large core polymer waveguides, which have been developed for increased alignment tolerance in passive fiber attachment, highly efficient variable optical attenuators are proposed. In order to find optimum device structures, 3-dimensional beam propagation method (BPM) simulations are performed. Heat distribution over the polymer film is calculated to find the 3-dimensional index profile data for the BPM simulation. Due to the small index contrast between the core and cladding materials in the large core waveguide, heat-induced radiation occurs for small heating power. While the ordinary VOA needs the temperature to change over $150^{\circ}C$ for 20 dB attenuation, the large core VOA requires only $70^{\circ}C$. In addition to the merit of passive fiber attachment, the proposed VOA has enhanced attenuation efficiency for the lower temperature change.

• Korean Journal of Optics and Photonics
• /
• v.16 no.6
• /
• pp.494-499
• /
• 2005

We have demonstrated a fiber short-wavelength filter with a good cut-off property using dissimilar dispersive properties between? a thermally expanded cored fiber and an external medium. Side-polishing is applied to coupling between the fiber and the external medium. The experimental results revealed that the bend edge wavelength can be adjusted by controlling the degree of core expansion. Futhermore, the sharpness of wavelength response? was significantly? improved by employing expanded core fiber instead of a conventional single mode fiber. Tuning range of the band edge wavelength exceeded 400 m based on thermo-optic effect of the external medium.

• Korean Journal of Optics and Photonics
• /
• v.18 no.1
• /
• pp.79-83
• /
• 2007

A reconfigurable photonic microwave (MW) channel selective filter was demonstrated incorporating a $1{\times}2$ switch based on two tunable polymeric resonators with different free spectral ranges. Each resonator, consisting of two cascaded rings with an electrode formed on one of them, plays a role as an on/off switch through the thermooptic effect. The optical signal carrying the MW signal is routed to either port of the switch and detected to show the filtered output at the frequency determined by the free spectral range of the corresponding resonator. When the channel centered at 10 GHz was chosen, the extinction ratio was ${\sim}30dB$, the bandwidth 1 GHz, and the electrical power consumption 4.1 mW. For the other channel located at 20 GHz, we have achieved the extinction ratio of ${\sim}30dB$, the bandwidth of 2 GHz, and the required power of 8.0 mW. Finally the crosstalk between the selected and blocked channels was higher than 24 dB.

• Current Optics and Photonics
• /
• v.8 no.2
• /
• pp.162-169
• /
• 2024

This study investigates the temperature sensitivities of fiber Bragg grating (FBG) across a broad temperature spectrum ranging from -196 ℃ to 900 ℃. We developed the FBG temperature measurement system using a high-temperature tubular furnace and liquid nitrogen to supply consistent high and low temperatures, respectively. Our research showed that the FBG temperature sensitivity changed from 1.55 to 10.61 pm/℃ in the range from -196 ℃ to 25 ℃ when the FBG was packaged with a quartz capillary. In the 25-900 ℃ range, the sensitivity varied from 11.26 to 16.62 pm/℃. Contrary to traditional knowledge, the FBG temperature sensitivity was not constant. This inconsistency primarily stems from the nonlinear shifts in the thermo-optic coefficient and thermal expansion coefficient across this temperature spectrum. The theoretically predicted and experimentally determined temperature sensitivities of FBGs encased in quartz capillary were remarkably consistent. The greatest discrepancy, observed at 25 ℃, was approximately 1.3 pm/℃. Furthermore, it was observed that at 900 ℃, the FBG was rapidly thermally erased, exhibiting variable reflected intensity over time. This study focuses on the advancement of precise temperature measurement techniques in environments that experience wide temperature fluctuations, and has considerable potential application value.

• Journal of Biosystems Engineering
• /
• v.41 no.2
• /
• pp.108-115
• /
• 2016

Purpose: Radio frequency (RF) heating is a promising thawing method, but it frequently causes undesirable problems such as non-uniform heating. This can occur because of the food shape, component distribution, and initial temperature differences between food parts. In this study, RF heating was applied to the thawing of cylindrically shaped pork sirloin by changing the shape of electrodes and the surrounding temperature. Methods: Curved electrodes were utilized to increase the thawing uniformity of cylindrically shaped frozen meat. Pork sirloin in the shape of a half-circle column was frozen in a deep freezer at $-70^{\circ}C$ and then thawed by RF heating with flat and curved electrodes. In order to prevent fast defrosting of the food surface by heat transfer from air to the food, the temperature of the thawing chamber was varied by -5, -10, and $-20^{\circ}C$. The temperature values of the frozen pork sirloin during RF thawing were measured using fiber-optic thermo sensors. Results: After multiple applications of curved electrodes resembling the food shape, and a cooled chamber at $-20^{\circ}C$ the half-cylindrically shaped meat was thawed without surface burning, and the temperature values of each point were similarly increased. However, with the parallel electrode, the frozen meat was partially burned by RF heating and the temperature values of center were overheated. The uniform heating rate and heat transfer prevention from air to the food were crucial factors for RF thawing. In this study, these crucial factors were accomplished by using a curved electrode and lowering the chamber temperature. Conclusions: The curved shape of the electrode and the equipotential surface calculated from the modeling of the parallel capacitor showed the effect of uniform heating of cylindrically shaped frozen food. Moreover, the low chamber temperature was effective on the prevention of the surface burning during RF thawing.