• Proceedings of the IEEK Conference
• /
• 2002.06e
• /
• pp.319-322
• /
• 2002

In this Paper, we suggested the Half-Bridge inverter for the automotive HID electronic ballast. electronic ballast for automotive HID lamp should be supplied by low-frequency square wave avoiding the acoustic resonance(11kHz ∼ 825kHz). When the HID lamp is hot state, the electronic ballast should supply the sufficient current for a few milli-second to the lamp at the re-strike ignition state. that is called take-over current. We have introduced the new take-over current control method that could have reduced the peak current and supplied the sufficient take-over current.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.3
• /
• pp.140-146
• /
• 2003

In this paper, we suggested electronic ballast with the half bridge inverter for the automotive HID lamp. The electronic ballast for the automotive HID lamp should be supplied by the low-frequency square wave avoiding the acoustic resonance. When the HID lamp is hot state, the electronic ballast should supply the sufficient current to the take over to the lamp at the re-strike ignition state for a few milli-second. We have introduced the new take-over current control method that could have control operating frequency and minimize circuits to the take over current circuits.

• The Journal of the Korea Contents Association
• /
• v.22 no.4
• /
• pp.70-82
• /
• 2022

At the current stage of a semi-autonomous vehicle, there are situations in which the vehicle has to request take-over control to the driver quickly. However, current self-driving cars use only simple messages and warning sounds to notify drivers when handing over control, so they do not adequately convey considerations of individual characteristics or explanations of various emergent situations. This study investigated how visual and auditory information and the efficacy of drivers in self-driving cars can improve efficient take-over requests between the car and the driver. We found that there were significant differences in driver's cognitive load, reliability, safety, usability, and usefulness according to the combination of three visual and auditory information provided in the experiment of the take-over request situation. The results of this study are expected to help design self-driving vehicles that can communicate more safely and efficiently with drivers in urgent control transition situations.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1871-1873
• /
• 1997

The conventional current transformers are often take faults and out of order that for detect to over current of electric power lines because electromagnetic interference. But, it is possible to implement protection relay of high reliability using optical magnetic field sensor which are immunity and small size. The optical magnetic field sensor is possible to rapidly detect to over current and recover when electric power line have fault. And it is not necessary to make with capacitance of electric power lines as optical magnetic field sensor is have linearity from 0 to about 20kA. In this study, we designed and constructed compensative feedback circuit in order to minimize of optical power intensity variation with environ- mental variations(temperature, drive current) of light source. And this system have highest optical advantages and reliability.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.3
• /
• pp.52-58
• /
• 2008

The importance of. identifying the causes of electrical faults cannot be overstated because of the accidents caused by over-current that take place at the home, the office and electrical facilities due to misuse, poor products and system faults. It is necessary to gather objective, scientific data pertaining to electrical fault investigation in a product liability(PL) environment. To date, no database(DB) has been built concerning the accurate cause analysis of faultyfacilities. In this paper, accident hazard and arc scattering when over-current flows in copper wire was investigated. It was found that when over-current flows in a copper wire, the copper wire became heated and bent and beads were scattered around the wire with a flash. It was determinedthat the fusing current and time was related to the current rise per second. For example, when the current rise per second was largethe fusing current was higher than when the current rise per second was small, and the beads dispersed along a wide area. Fusing time, however, was shorter. The possibility of electrical fault became highest when the fusing current was higher. As the current rise per second is short, the dendrite structure is distributed in the surface of the copper wire. These experimental results can be utilized for a fault process DB system in the investigation and the prevention of electrical faults.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.273-274
• /
• 2008

According to current RRC procedures, network does not know either how long it will take the RRC reconfiguration message (such as Physical Channel Reconfiguration (PCR)/Transport Channel Reconfiguration (TCR)/Radio Bearer Reconfiguration (RBR)) to be transmitted over the source cell or how long the UE will take to reconfigure on receiving the message, it has to assume the worst-case. Thus, it typically indicates a conservative activation time, leading to potentially large interruption for voice traffic, particularly if the source cell signal strength has degraded. This proposals allow the UE to receive the serving cell related information (carried today in PCR/RBR/TCR message) in an Active Set Update message.

• Journal of Power Electronics
• /
• v.4 no.2
• /
• pp.87-95
• /
• 2004

A new fast-response high-current clamp DC-DC converter circuit design is presented that will meet the requirements and features of the new generation of microprocessors and digital systems. The clamp in the proposed converter amplifies the current in case of severe load changes and is able to produce high slew rate of output current and capability to keep constant the output voltage. This proposed high-current clamp technique is theoretically loss less, low cost and easy to implement with simple control scheme. This is modified from a basic buck topology by replacing the output inductor with two magnetically coupled inductors. Inductors are difference in inductance, one has large inductance and other has small inductance. The inductor with small inductance will take over the output inductor during fast load transient. It speedup the output current slew rate and reduce the output voltage drop in the case of heavy burden load changes.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.6
• /
• pp.565-573
• /
• 2007

The effect of wave and current interactions on irregular wave transformation over a submerged elliptic shoal is investigated based on numerical simulations of the Vincent and Briggs experiment [Vincent, C.L., Briggs, M.J., 1989. Refraction-diffraction of irregular waves over a mound. Journal of Waterway, Port, Coastal and Ocean Engineering, 115(2), pp. 269-284]. The numerical simulations are conducted by a combination of REF/DIF S(a wave model) and SHORECIRC(a current model) and a time dependent phase-resolving wavecurrent model, FUNWAVE. In the simulations, the breaking-induced currents defocus waves behind the shoal and bring on a wave shadow zone that shows relatively low wave height distributions. The computed results of the combined model system agree better with the measurements than the computed results obtained by neglecting wave-current interaction do. In addition, the results of FUNWAVE show a good agreement with the measurements. The agreement indicates that it is necessary to take into account the effect of breaking-induced current on wave refraction when wave-breaking occurs over a submerged shoal.

• Ocean Systems Engineering
• /
• v.5 no.2
• /
• pp.125-138
• /
• 2015

In this study, hydrodynamic performance of a 400 mm diameter horizontal axis marine current turbine model was tested in a cavitation tunnel with 1.21 m x 0.8 m cross-section for over a range of tip speed ratios. Torque and thrust data, as well as cavitation visualizations, for certain operating conditions were acquired. Experimental results indicated that the turbine can be exposed to significant amount of sheet and cloud cavitation over the blades along with vortex cavitation at the blade tips. Inception and distribution of cavitation along the blades of the model turbine were then modelled numerically for design operating conditions using a vortex lattice method. The method was also applied to a turbine tested previously and obtained results were compared with the data available. The comparison between simulation results and experimental data showed a slight difference in terms of span-wise extent of the cavitation region. The cloud and tip vortex cavity observed in experiments cannot be modelled due to the fact that the VLM lacks the ability to predict such types of cavitation. Notwithstanding, the use of such prediction methods can provide a reasonably accurate approach to estimate, therefore take the hydrodynamic effects of cavitation into account in design and analysis of marine current turbines.

• Korean Journal of Construction Engineering and Management
• /
• v.4 no.1 s.13
• /
• pp.114-121
• /
• 2003

The precise quantity of materials is not yet taken off by the CAD system although it has Influenced in design productivity and automatic estimate. And various estimate systems developed so far deal with the quantity take-off of building members separately, which caused to over-estimate the part of each member. Therefore, the purpose of this paper is to develop algorithms of more precise estimate than that of current estimate by solving boundary conditions of the connection parts of building members, such as column, girder, beam, wall and slab. The algorithms are proposed to take off the quantity of concrete and form work and they will be used for the estimate of building structure more precisely and automatically than ever.