• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.151-156
• /
• 2015

In order to improve the properties of high-temperature superconducting wire for superconducting cable system, we optimized the electro-polishing (EP), ion-beam assisted deposition (IBAD), superconducting (SC) layer, and baking (heat) treatment. The buffer layer was deposited on electro-polished substrate with RMS roughness ($R_{RMS}$) less than 5 nm. The IBAD process was carried out at $V_{beam}$: 1100 V and $V_{accel}$: 850 V that resulted in highly crystalline film of $LaMnO_3$. Chemical composition of SC layer is key to higher critical current, and we found that composition can be determined by surface color of SC layer. We adopt a proprietary contorl system based on RGB analysis of the surface and achieved critical current of 150 A/4 mm-width. The proposed baking treatment resulted in decreasing of about 10% of fraction defects.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.169-169
• /
• 2012

The high-temperature superconductor YBa2Cu3O7-x (YBCO) have attached attentions because of a high superconducting transition temperature, low surface resistance, high superconducting critical current density (Jc), and superior superconducting capability under magnetic field. Moreover, the Jc of YBCO superconductors can be enhanced by adding impurities to the YBCO films for vortex-pinning. Understanding and controlling pinning centers are key factors to realize high Jc superconductors. We synthesized vertically-aligned ZnO nanorods on SrTiO3 (STO) substrates by catalyst-free metal-organic chemical vapor deposition (MOCVD), and subsequently, deposited YBCO films on the ZnO nanorods/STO templates using pulsed laser deposition (PLD). The various techniques were used to analyze the structural and interfacial properties of the YBCO/ZnO nanorods/STO hybrid structures. SEM, TEM, and XRD measurements demonstrated that YBCO films on ZnO nanorods/STO were well crystallized with the (001) orientation. EXAFS measurements from YBCO/ZnO nanorods/STO at Cu K edge demonstrated that the local structural properties around Cu atoms in YBCO were quite similar to those of YBCO/STO.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.34-37
• /
• 1999

We have fabricated YBCO/STO/YBCO multilayer by the pulsed laser deposition method varing the deposition condition of insulating STO layer. Superconducting properties of both YBCO layers are sensitively affected by the deposition condition of STO layer. We obtained the upper YBCO layer of T$_{c(zero)}\;{\sim}\;$90 K with a good reproducibility, however, T$_{c(zero)}$ of lower YBCO layer was decreased to about 80 K maybe due to the oxygen loss during the deposition of STO layer. Superconducting properties of both YBCO layers at every fabrication step were measured in order to study the reason for the deterioration of superconducting properties.

• Progress in Superconductivity and Cryogenics
• /
• v.3 no.2
• /
• pp.1-4
• /
• 2001

For the practical use of a superconducting wire to magnet application, it is important to assess the Young modulus and other mechanical properties of HTS tapes. In order to establish a test method of mechanical properties for oxide composite superconductors. tensile tests of Bi-2223 multi- filamentary tapes were carried out at room temperature, as an activity of the International round robin test proposed by the committee of VAMAS/TWA 16-Subrgroup. The tapes consisting of mutli-filamentary showed a three stage tensile behavior. At the initial stage of the stress-streain curve. The elastic deformation existed in a quite nattrow strain region. But the plastic deformation was observed in a wide strain region due to the platic flow of the Ag alloy matrix. The results of RRT were also reported and discussed.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.26-29
• /
• 2002

Polyimide-epoxysilane (coupling agent) composites were reacted with oligomeric PDMS, a condensation product of difunctional silane, by a sol-gel process and were then dried into films. And then, the surface, mechanical, and electric properties were measured. The study showed that PDMS existed in the polymide matrix by the use of FT-IR. In the mechanical properties, the maximum elongation and toughness was increased in the polyimide with silane-groups. But the maximum tensile strength was slightly decreased. And the intensive dispersion of the silane-groups on the surface of polyimide was ascertained through XPS measurement. In the electric properties. AC break down voltage was increased by increasing the amount of difunctional silane. This experiment showed that PDMS added polyimide had better mechanical and electric properties than classical materials.

• Journal of Magnetics
• /
• v.13 no.4
• /
• pp.128-131
• /
• 2008

We have investigated the electronic structures and magnetic properties of both undoped and doped bcc Ni using the full-potential linearized augmented plane wave (FLAPW) band method. A ferromagnetic ground state is obtained at the equilibrium volume of bcc Ni. When the system is under strain, the nonmagnetic ground state is stabilized. When the Ni is doped with V, the $Ni_{16-x}V_x$ material loses its magnetic properties when x > 2. We have also discussed the possible superconducting properties of $Ni_{16-x}V_x$.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1219-1221
• /
• 2005

We improved quench properties of a superconducting fault current limiter(SFCL) components based on YBCO thin films. This consists of three components with nearly identical properties and one with slightly difference properties. The units were connected in series and first of parallel to increase the current and voltage ratings. It have caused significantly imbalanced power distribution. The imbalance remarkably improved by connecting a shunt reactor to the SFCL component in parallel.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.511-517
• /
• 2001

We evaluated the electrical properties of 37 multifilamentary jointed tapes processed by superconducting joint. In the superconducting joining method, a lap-joint was used. Tapes were selectively etched, and exposed superconducting cores of the two tapes were brought into contact with each other and then only the joined region was uniaxially pressed in the range of 1,000 to 2,50 MPa. The critical current ratio(CCR) and n-value of the jointed tape were evaluated as a function of uniaxial pressure and number of step in the contacting region. It was observed that the CCR was dependent on the number of step, but almost independent of uniaxial pressure. The highest critical current ratio and n-value were obtained to be 58% and 26%, respectively, for the jointed tape to the tape itself.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.122-125
• /
• 1991

This paper deals with hysteresis losses on the superconducting slap by using type II superconducting theory and classical maxwell equations. Transport current is transmitted to the longitudual direction and applied magnetic field is perpendicular to the slap length and simultaneously parallel to the plat. And the sinusoidal transport currents and the magnetic fields are applied to the slap. Properties of hysteresis loss can be understood, using computer simulation with apply field, transport current and phasor difference. From this result the efficiency and the stability of superconducting system can be enhanced.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.182-183
• /
• 2006

An electromagnetic memory effect observed in superconducting YBCO system was studied. From the measurement of differential conductance, it was cleared that the mechanism of electromagnetic memory can not be explained by using conventional flux flow model. By changing the density of external magnetic flux, changes m inductance of a coil in which a superconducting bar is inserted were also measured. It was concluded that the electromagnetic memory effect aries from the interaction between the trapped magnetic flux and the weak link of the filament formed in the superconducting bar.